the i/o regions of the vnode data space. The implementation is quite
simple-minded, it uses the list of the lock requests, ordered by
arrival time. Each request may be for read or for write. The
implementation is fair FIFO.
MFC after: 2 month
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
Tested by: sbruno
MFC after: 5 weeks
via `camcontrol tags ... -N ...`. There is no need to tune it in
usual cases, but some users want to have it for debugging purposes.
MFC after: 2 weeks
DEVICE_RESUME() should be done before AcpiLeaveSleepState() because
PCI config space evaluation can be occurred during control method
executions.
This should fix one of the hang up problems on resuming.
MFC after: 3 days
compiled into the kernel. This allows us to boot the same kernel on
machines with different master clock frequencies, so long as we can
determine the main clock frequency accurately. Cleanup the pmc clock
init function so it can be called in early boot so we can use the
serial port just after we call cninit.
# We have two calls to at91_pmc_clock_init for reasons unknown, that will
# be fixed later -- it is harmless for now.
to this pmap.c. This new r/w lock is used primarily to synchronize access
to the TTE lists. However, it will be used in a somewhat unconventional
way. As finer-grained TTE list locking is added to each of the pmap
functions that acquire this r/w lock, its acquisition will be changed from
write to read, enabling concurrent execution of the pmap functions with
finer-grained locking.
Reviewed by: attilio
Tested by: flo
MFC after: 10 days
DataFlash.
- Add a mapping for the Nut/OS configuration DataFlash partition according
to the board manual (but not known to either Linux or U-Boot (patches).
since batch_len is unused by Linux driver, it seems that it is sometimes
gets passed wrong. This causes command buffer corruption and GPU hung.
Old GEMified DDX drivers that needs this workaround are not supported.
MFC after: 1 month
Currently, 'ifconfig laggX down' does not remove members from this
lagg(4) interface. So, 'service netif stop laggX' followed by
'service netif start laggX' will choke, because "stop" will leave
interfaces attached to the laggX and ifconfig from the "start" will
refuse to add already-existing interfaces.
The real-world case is when I am bundling together my Ethernet and
WiFi interfaces and using multiple profiles for accessing network in
different places: system being booted up with one profile, but later
this profile being exchanged to another one, followed by 'service
netif restart' will not add WiFi interface back to the lagg: the
"stop" action from 'service netif restart' will shut down my main WiFi
interface, so wlan0 that exists in the lagg0 will be destroyed and
purged from lagg0; the "start" action will try to re-add both
interfaces, but since Ethernet one is already in lagg0, ifconfig will
refuse to add the wlan0 from WiFi interface.
Since adding the interface to the lagg(4) when it is already here
should be an idempotent action: we're really not changing anything,
so this fix doesn't change the semantics of interface addition.
Approved by: thompsa
Reviewed by: emaste
MFC after: 1 week
headers for TSO but also for generic checksum offloading. Ideally we
would only have one common function shared amongst all drivers, and
perhaps when updating them for IPv6 we should introduce that.
Eventually we should provide the meta information along with mbufs to
avoid (re-)parsing entirely.
To not break IPv6 (checksums and offload) and to be able to MFC the
changes without risking to hurt 3rd party drivers, duplicate the v4
framework, as other OSes have done as well.
Introduce interface capability flags for TX/RX checksum offload with
IPv6, to allow independent toggling (where possible). Add CSUM_*_IPV6
flags for UDP/TCP over IPv6, and reserve further for SCTP, and IPv6
fragmentation. Define CSUM_DELAY_DATA_IPV6 as we do for legacy IP and
add an alias for CSUM_DATA_VALID_IPV6.
This pretty much brings IPv6 handling in line with IPv4.
TSO is still handled in a different way and not via if_hwassist.
Update ifconfig to allow (un)setting of the new capability flags.
Update loopback to announce the new capabilities and if_hwassist flags.
Individual driver updates will have to follow, as will SCTP.
Reported by: gallatin, dim, ..
Reviewed by: gallatin (glanced at?)
MFC after: 3 days
X-MFC with: r235961,235959,235958
to this pmap.c. This new r/w lock is used primarily to synchronize access
to the PV lists. However, it will be used in a somewhat unconventional
way. As finer-grained PV list locking is added to each of the pmap
functions that acquire this r/w lock, its acquisition will be changed from
write to read, enabling concurrent execution of the pmap functions with
finer-grained locking.
X-MFC after: r236045
There are currently no in-tree consumers; I'm adding it now for use by
vendor code. This matches the change OpenBSD made while implementing
MPLS in gif(4).
- Fix some math errors in mmc_decode_csd_sd().
- Fix incorrect arguments to mmc_send_app_op_cond() in mmc_go_discovery().
- Add reporting of CSD for debug purposes.
- Add detection (and skipping) of password-locked cards.
- Add setting of block length on card if necessary.
Submitted by: Patrick Kelsey
MFC after: 3 days
1948 zpool list should show more detailed pool information
Display per-vdev information with "zpool list -v".
The added expandsize property has currently no value on FreeBSD.
This changeset allows adding expansion support to individual vdevs
in the future.
References:
https://www.illumos.org/issues/1948
Obtained from: illumos (issue #1948)
MFC after: 2 weeks
