all new devices added between our r211022 and their git revision
93ad03d60b5b18897030038234aa2ebae8234748
Also correct a Foxconn entry.
MFC after: 1 week
bus_dma(9)'s capability which honors boundary restrictions of DMA
tag for dynamic buffers. However it seems this does not work well
and it triggered watchodg timeouts on controller that has the
hardware bug. It's not clear whether there is still another
hardware bug not mentioned in errata. This should be revisited
since this change shall make use of bounce buffers which in turn
reduces performance a lot on systems that have more than 4GB
memory.
Reported by: Michael L. Squires (mikes <> siralan dot org)
Tested by: Michael L. Squires (mikes <> siralan dot org)
MFC after: 3 days
mechanical change. This opens the door for using PV device drivers
under Xen HVM on i386, as well as more general harmonisation of i386
and amd64 Xen support in FreeBSD.
Reviewed by: cperciva
MFC after: 3 weeks
After controller updates control word in a RX LE, driver converts
it to host byte order. The checksum value in the control word is
stored in big endian form by controller. r205091 didn't account for
the host byte order conversion such that the checksum value was
incorrectly interpreted on big endian architectures which in turn
made all TCP/UDP frames dropped. Make RX checksum offload work
on any architectures by swapping the checksum value.
Reported by: Sreekanth M. ( kanthms <> netlogicmicro dot com )
Tested by: Sreekanth M. ( kanthms <> netlogicmicro dot com )
supposed to be APs and the later 24 are pre-configured as STAs. A wrong
condition during initialization is responsible for not configuring the last
8 array members. This is results in being able to create more than 8,
possible uninitialized, AP-VAPs.
PR: kern/153549
Submitted by: Erik Fonnesbeck <efonnes at gmail.com>
MFC after: 2 weeks
The controller is commonly found on DM&P Vortex86 x86 SoC. The
driver supports all hardware features except flow control. The
flow control was intentionally disabled due to silicon bug.
DM&P Electronics, Inc. provided all necessary information including
sample board to write driver and answered many questions I had.
Many thanks for their support of FreeBSD.
H/W donated by: DM&P Electronics, Inc.
modification of memory which was already free'd and eventually in:
wpi0: could not map mbuf (error 12)
wpi0: wpi_rx_intr: bus_dmamap_load failed, error 12
and an usuable device.
PR: kern/144898
MFC after: 3 days
md(4) to using M_WAITOK malloc calls.
M_NOWAITOK allocations may fail when enough memory could be freed, but not
immediately. E.g. SU UFS becomes quite unhappy when metadata write return
error, that would happen for failed malloc() call.
Reported and tested by: pho
MFC after: 1 week
table is present, then the acpi_ec(4) driver will allocate its resources
from nexus0 before the acpi0 device reserves resources for child devices.
Reviewed by: jkim
manual 1000BASE-T modes of DP83865 only work together with other National
Semiconductor PHYs.
- Spell 10BASE-T correctly
- Remove some redundant braces.
condition in proc_rwmem() and to (2) simplify the implementation of the
cxgb driver's vm_fault_hold_user_pages(). Specifically, in proc_rwmem()
the requested read or write could fail because the targeted page could be
reclaimed between the calls to vm_fault() and vm_page_hold().
In collaboration with: kib@
MFC after: 6 weeks
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
controller with Card Read Host Controller. These controllers are
multi-function devices and have the same ethernet core of
JMC250/JMC260. Starting from REVFM 5(chip full mask revision)
controllers have the following features.
o eFuse support
o PCD(Packet Completion Deferring)
o More advanced PHY power saving
Because these controllers started to use eFuse, station address
modified by driver is permanent as if it was written to EEPROM. If
you have to change station address please save your controller
default address to safe place before reprogramming it. There is no
way to restore factory default station address.
Many thanks to JMicron for continuing to support FreeBSD.
HW donated by: JMicron
a 2GHz channel with appropriate flags set to sc->config. Due to not zeroing
sc->config for auth/assoc those flags are still set while trying to connect
on a 5GHz channel.
MFC after: 3 days
