Now an interface name can be specified for nptv6 instance instead of
ext_prefix. The module will track if_addr_ext events and when suitable
IPv6 address will be added to specified interface, it will be configured
as external prefix. When address disappears instance becomes unusable,
i.e. it doesn't match any packets.
Reviewed by: 0mp (manpages)
Tested by: Dries Michiels <driesm dot michiels gmail com>
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D17765
Make it clear that ipfw action set for layer2 frames it a bit limited.
PR: 59835
Reviewed by: yuripv
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D17719
to switch the output method in run-time. Also document some sysctl
variables that can by changed for NAT64 module.
NAT64 had compile time option IPFIREWALL_NAT64_DIRECT_OUTPUT to use
if_output directly from nat64 module. By default is used netisr based
output method. Now both methods can be used, but they require different
handling by rules.
Obtained from: Yandex LLC
MFC after: 3 weeks
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D16647
returns error.
Now -q option only makes it quiet. And when -f flag is specified, the
command will ignore errors and continue executing with next batched
command.
MFC after: 2 weeks
"record-state" is similar to "keep-state", but it doesn't produce implicit
O_PROBE_STATE opcode in a rule. "set-limit" is like "limit", but it has the
same feature as "record-state", it is single opcode without implicit
O_PROBE_STATE opcode. "defer-action" is targeted to be used with dynamic
states. When rule with this opcode is matched, the rule's action will
not be executed, instead dynamic state will be created. And when this
state will be matched by "check-state", then rule action will be executed.
This allows create a more complicated rulesets.
Submitted by: lev
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D1776
sockstat(1), ugidfw(8)
These are the last of the jail-aware userland utilities that didn't work
with names.
PR: 229266
MFC after: 3 days
Differential Revision: D16047
ip_reass() expects IPv4 packet and will just corrupt any IPv6 packets
that it gets. Until proper IPv6 fragments handling function will be
implemented, pass IPv6 packets to next rule.
PR: 170604
MFC after: 1 week
This is similar to the TCP case. where a TCP RST segment can be sent.
There is one limitation: When sending an ABORT in response to an incoming
packet, it should be tested if there is no ABORT chunk in the received
packet. Currently, it is only checked if the first chunk is an ABORT
chunk to avoid parsing the whole packet, which could result in a DOS attack.
Thanks to Timo Voelker for helping me to test this patch.
Reviewed by: bcr@ (man page part), ae@ (generic, non-SCTP part)
Differential Revision: https://reviews.freebsd.org/D13239
The module is designed for modification of a packets of any protocols.
For now it implements only TCP MSS modification. It adds the external
action handler for "tcp-setmss" action.
A rule with tcp-setmss action does additional check for protocol and
TCP flags. If SYN flag is present, it parses TCP options and modifies
MSS option if its value is greater than configured value in the rule.
Then it adjustes TCP checksum if needed. After handling the search
continues with the next rule.
Obtained from: Yandex LLC
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Yandex LLC
No objection from: #network
Differential Revision: https://reviews.freebsd.org/D10150
Since the state name is an optional argument, it often can conflict
with other options. To avoid ambiguity now the state name must be
prefixed with a colon.
Obtained from: Yandex LLC
MFC after: 2 week
Sponsored by: Yandex LLC
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
The keep-state, limit and check-state now will have additional argument
flowname. This flowname will be assigned to dynamic rule by keep-state
or limit opcode. And then can be matched by check-state opcode or
O_PROBE_STATE internal opcode. To reduce possible breakage and to maximize
compatibility with old rulesets default flowname introduced.
It will be assigned to the rules when user has omitted state name in
keep-state and check-state opcodes. Also if name is ambiguous (can be
evaluated as rule opcode) it will be replaced to default.
Reviewed by: julian
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6674
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
to obtain IPv4 next hop address in tablearg case.
Add `fwd tablearg' support for IPv6. ipfw(8) uses INADDR_ANY as next hop
address in O_FORWARD_IP opcode for specifying tablearg case. For IPv6 we
still use this opcode, but when packet identified as IPv6 packet, we
obtain next hop address from dedicated field nh6 in struct table_value.
Replace hopstore field in struct ip_fw_args with anonymous union and add
hopstore6 field. Use this field to copy tablearg value for IPv6.
Replace spare1 field in struct table_value with zoneid. Use it to keep
scope zone id for link-local IPv6 addresses. Since spare1 was used
internally, replace spare0 array with two variables spare0 and spare1.
Use getaddrinfo(3)/getnameinfo(3) functions for parsing and formatting
IPv6 addresses in table_value. Use zoneid field in struct table_value
to store sin6_scope_id value.
Since the kernel still uses embedded scope zone id to represent
link-local addresses, convert next_hop6 address into this form before
return from pfil processing. This also fixes in6_localip() check
for link-local addresses.
Differential Revision: https://reviews.freebsd.org/D2015
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
re-links dynamic states to default rule instead of
flushing on rule deletion.
This can be useful while performing ruleset reload
(think about `atomic` reload via changing sets).
Currently it is turned off by default.
MFC after: 2 weeks
Sponsored by: Yandex LLC
Setting DSCP support is done via O_SETDSCP which works for both
IPv4 and IPv6 packets. Fast checksum recalculation (RFC 1624) is done for IPv4.
Dscp can be specified by name (AFXY, CSX, BE, EF), by value
(0..63) or via tablearg.
Matching DSCP is done via another opcode (O_DSCP) which accepts several
classes at once (af11,af22,be). Classes are stored in bitmask (2 u32 words).
Many people made their variants of this patch, the ones I'm aware of are
(in alphabetic order):
Dmitrii Tejblum
Marcelo Araujo
Roman Bogorodskiy (novel)
Sergey Matveichuk (sem)
Sergey Ryabin
PR: kern/102471, kern/121122
MFC after: 2 weeks
Instead, add protocol specific mbuf flags M_IP_NEXTHOP and
M_IP6_NEXTHOP. Use them to indicate that the mbuf's chain
contains the PACKET_TAG_IPFORWARD tag. And do a tag lookup
only when this flag is set.
Suggested by: andre
