Much of the code was common to begin with. There is one nit, which is likely
not an issue at all. With the old code, the AIM machdep would __syncicache()
the entire kernel core at setup. However, in the unified setup, that seems to
hang on the MPC7455, perhaps because it's running later than before. Removing
this allows it to boot just fine. Examining the code, the FreeBSD loader
already does syncicache of the full kernel, and each module loaded, so this
doesn't appear to be an actual problem.
Initial code by Nathan Whitehorn.
Summary:
Book-E and AIM trap.c are almost identical, except for a few bits. This is step
1 in unifying them.
This also renumbers EXC_DEBUG, to not conflict with AIM vector numbers. Since
this is the only one thus far that is used in the switch statement in trap(),
it's the only one renumbered. If others get added to the switch, which conflict
with AIM numbers, they should also be renumbered.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2215
A couple of internal functions used by malloc(9) and uma truncated
a size_t down to an int. This could cause any number of issues
(e.g. indefinite sleeps, memory corruption) if any kernel
subsystem tried to allocate 2GB or more through malloc. zfs would
attempt such an allocation when run on a system with 2TB or more
of RAM.
Note to self: When this is MFCed, sparc64 needs the same fix.
Differential revision: https://reviews.freebsd.org/D2106
Reviewed by: kib
Reported by: Michael Fuckner <michael@fuckner.net>
Tested by: Michael Fuckner <michael@fuckner.net>
MFC after: 2 weeks
executables. The goal here, not yet accomplished, is to let the e500 kernel
run under QEMU by setting KERNBASE to something that fits in low memory and
then having the kernel relocate itself at runtime.
have the same meaning and occupy the same memory address in the trapframe
courtesy of union. Avoid some pointless #ifdef by spelling them both 'DAR'
in the trapframe.
this change is to improve concurrency:
- Drop global state stored in the shadow overflow page table (and all other
global state)
- Remove all global locks
- Use per-PTE lock bits to allow parallel page insertion
- Reconstruct state when requested for evicted PTEs instead of buffering
it during overflow
This drops total wall time for make buildworld on a 32-thread POWER8 system
by a factor of two and system time by a factor of three, providing performance
20% better than similarly clocked Core i7 Xeons per-core. Performance on
smaller SMP systems, where PMAP lock contention was not as much of an issue,
is nearly unchanged.
Tested on: POWER8, POWER5+, G5 UP, G5 SMP (64-bit and 32-bit kernels)
Merged from: user/nwhitehorn/ppc64-pmap-rework
Looked over by: jhibbits, andreast
MFC after: 3 months
Relnotes: yes
Sponsored by: FreeBSD Foundation
and POWER8. This instruction set unifies the 32 64-bit scalar floating
point registers with the 32 128-bit vector registers into a single bank
of 64 128-bit registers. Kernel support mostly amounts to saving and
restoring the wider version of the floating point registers and making
sure that both scalar FP and vector registers are enabled once a VSX
instruction is executed. get_mcontext() and friends currently cannot
see the high bits, which will require a little more work.
As the system compiler (GCC 4.2) does not support VSX, making use of this
from userland requires either newer GCC or clang.
Relnotes: yes
Sponsored by: FreeBSD Foundation
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
every possible trap address by default. This also makes sure the kernel
notices (and panics at) traps from newer CPUs that the kernel was not
expecting rather than executing gibberish memory.
A "size" symbol with its address set to the length of handler would be
shifted forward with all other addresses when relocations are processed.
Instead, just note the end and do the subtraction at runtime.
mostly a no-op since all currently-supported instances of these CPUs give
the number of SLB slots in the device tree, but keep it here as well just
in case.
instructions to call through pointers instead. In general, these are set
implicitly through relocation processing. One has to be set explicitly in
machdep.c, however, to fit one handler in the tiny (8 instruction) space
available.
Reviewed by: andreast
Differential revision: D1554
Tested on: UP and SMP G5, Cell, POWER5+
sequences, like are used to read the HIDs. This is both easier to read
and avoids a miscompilation by GCC in certain circumstances. Also avoid
double restoration of HID4 and HID5.
MFC after: 2 weeks
PVO pool size. The default errs on the exceedingly large side, so absent
any intelligent automatic tuning, at least let the user set it to save
RAM on memory-constrained systems.
MFC after: 2 weeks
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
the Open Firmware, as provided by petitboot, for example. Note that this is
not quite complete, since RTAS instantiation still depends on callable
firmware.
MFC after: 2 weeks
It's redundant at the moment since it can be obtained from the trapframe
on the architectures where DTrace is supported, but this won't be the case
with ARM.
Summary:
Revert the initial FBT-with-KDB changes for trap_subr*.S, and instead use the
db_trap filter function to handle dtrace trap filtering. With this, the MMU is
enabled by the support code, simplifying the codepath altogether.
Test Plan: Tested on my G4 PowerBook
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1207
MFC after: 3 weeks
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
When the FreeBSD kernel is loaded from Xen the symtab and strtab are
not loaded the same way as the native boot loader. This patch adds
three new global variables to ddb that can be used to specify the
exact position and size of those tables, so they can be directly used
as parameters to db_add_symbol_table. A new helper is introduced, so callers
that used to set ksym_start and ksym_end can use this helper to set the new
variables.
It also adds support for loading them from the Xen PVH port, that was
previously missing those tables.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
ddb/db_main.c:
- Add three new global variables: ksymtab, kstrtab, ksymtab_size that
can be used to specify the position and size of the symtab and
strtab.
- Use those new variables in db_init in order to call db_add_symbol_table.
- Move the logic in db_init to db_fetch_symtab in order to set ksymtab,
kstrtab, ksymtab_size from ksym_start and ksym_end.
ddb/ddb.h:
- Add prototype for db_fetch_ksymtab.
- Declate the extern variables ksymtab, kstrtab and ksymtab_size.
x86/xen/pv.c:
- Add support for finding the symtab and strtab when booted as a Xen
PVH guest. Since Xen loads the symtab and strtab as NetBSD expects
to find them we have to adapt and use the same method.
amd64/amd64/machdep.c:
arm/arm/machdep.c:
i386/i386/machdep.c:
mips/mips/machdep.c:
pc98/pc98/machdep.c:
powerpc/aim/machdep.c:
powerpc/booke/machdep.c:
sparc64/sparc64/machdep.c:
- Use the newly introduced db_fetch_ksymtab in order to set ksymtab,
kstrtab and ksymtab_size.
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
by the combination of r268591 and r269134: When we attempt to add the
wired attribute to an existing mapping, moea{,64}_pvo_enter() do nothing.
(They only set the wired attribute on newly created mappings.)
Tested by: andreast
pmap_unwire(), the call to MOEA64_PVO_TO_PTE() must be performed before
any changes are made to the PVO. Otherwise, MOEA64_PVO_TO_PTE() will
panic.
Reported by: andreast
calling mmap on /dev/mem and add a handler for the possible userland
machine checks that may result. Remove some pointless and wrong copy/paste
that has been in here for a decade as well.
This results in a /dev/mem with identical semantics to the x86 version.
MFC after: 1 week
the upstream implementation and helps ensure that a trap induced by tracing
fbt::trap:entry is handled without recursively generating another trap.
This makes it possible to run most (but not all) of the DTrace tests under
common/safety/ without triggering a kernel panic.
Submitted by: Anton Rang <anton.rang@isilon.com> (original version)
Phabric: D95
entry was being tested. We were incrementing and decrementing the pmap's
wired mapping count based on whether the physical page being mapped or
unmapped was cache coherent, not whether it was a wired mapping.
Reviewed by: nwhitehorn
