The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
Remove old bits of data concat for 'ascii' field.
Remove special SIOCGIFSTATUS handling from if.c (which Coverity yells at).
Reported by: Coverity
Coverity CID: 1147174
MFC after: 2 weeks
WARNING: icl_pdu_check_data_digest: data digest check failed; got 0xf23b,
should be 0xdb7f23b
Tested by: Darcy Birkbeck
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
value. The "Intel Lynx Point" XHCI controller found in the MBP2013 has
been observed to not always set the event interrupt bit while there
are events to consume in the event ring.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
the spoofed identify data into the user buffer rather than issuing the
command to the controller, since Chatham IDENTIFY data is always spoofed.
While here, fix a bug in the spoofed data for Chatham submission and
completion queue entry sizes.
Sponsored by: Intel
MFC after: 3 days
Most relevant features:
- netmap emulation on any NIC, even those without native netmap support.
On the ixgbe we have measured about 4Mpps/core/queue in this mode,
which is still a lot more than with sockets/bpf.
- seamless interconnection of VALE switch, NICs and host stack.
If you disable accelerations on your NIC (say em0)
ifconfig em0 -txcsum -txcsum
you can use the VALE switch to connect the NIC and the host stack:
vale-ctl -h valeXX:em0
allowing sharing the NIC with other netmap clients.
- THE USER API HAS SLIGHTLY CHANGED (head/cur/tail pointers
instead of pointers/count as before). This was unavoidable to support,
in the future, multiple threads operating on the same rings.
Netmap clients require very small source code changes to compile again.
On the plus side, the new API should be easier to understand
and the internals are a lot simpler.
The manual page has been updated extensively to reflect the current
features and give some examples.
This is the result of work of several people including Giuseppe Lettieri,
Vincenzo Maffione, Michio Honda and myself, and has been financially
supported by EU projects CHANGE and OPENLAB, from NetApp University
Research Fund, NEC, and of course the Universita` di Pisa.
freeing them.
The current code would walk the list and call the buffer free, which
didn't remove it from any lists before pushing it back on the free list.
Tested: AR9485, STA mode
Noticed by: dillon@apollo.dragonflybsd.org
related to setting up static device mappings. Since it was only used by
arm/mv/mv_pci.c, it's now just static functions within that file, plus
one public function that gets called only from arm/mv/mv_machdep.c.
obsolete. This involves the following pieces:
- Remove it entirely on PowerPC, where it is not used by MD code either
- Remove all references to machine/fdt.h in non-architecture-specific code
(aside from uart_cpu_fdt.c, shared by ARM and MIPS, and so is somewhat
non-arch-specific).
- Fix code relying on header pollution from machine/fdt.h includes
- Legacy fdtbus.c (still used on x86 FDT systems) now passes resource
requests to its parent (nexus). This allows x86 FDT devices to allocate
both memory and IO requests and removes the last notionally MI use of
fdtbus_bs_tag.
- On those architectures that retain a machine/fdt.h, unused bits like
FDT_MAP_IRQ and FDT_INTR_MAX have been removed.
static device mappings.
This SoC relied heavily on the fact that all devices were static-mapped
at a fixed address, and it (rather bogusly) used bus_space read and write
calls passing hard-coded virtual addresses instead of proper bus handles,
relying on the fact that the virtual addresses of the mappings were known
at compile time, and relying on the implementation details of arm
bus_space never changing. All such usage was replaced with calls to
bus_space_map() to obtain a proper bus handle for the read/write calls.
This required adjusting some of the #define values that map out hardware
registers, and some of them were renamed in the process to make it clear
which were defining absolute physical addresses and which were defining
offsets. (The ones that just define offsets don't appear to be referenced
and probably serve no value other than perhaps documentation.)
Using unmapped BIOs causes failure inside bus_dmamap_sync, since
this function requires valid MVA address, which is not present
if mapping is not set up.
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Atmel boards I have.
# All Samsung, Toshiba and SanDisk parts will need to be in this table
# since they don't conform to the ONFI specification (they are all Toggle
# parts). There's some standards for the additional bytes so there's some hope
# to decode them automatically on a per-vendor basis, but even that has
# problems (and is what motivated the ONFI parameter page).
header is split out into its own BD for processing by the firmware. When
this split occurred the data length in the BD was not being set correctly
resulting in packet corruption.
Approved by: davidcd (mentor)
by receive code waiting for data digest even when the data segment was
empty. It didn't actually read it, but it waited until those four bytes
become available in the socket buffer, i.e. until any other PDU (such as NOP)
came in.
PR: kern/185240
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
hw.ral.msi_disable (defaulting to using MSI).
- Probe with BUS_PROBE_DEFAULT instead of 0.
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Release resources again in case attaching fails.
- Quiesce the interrupt before detaching.
- Sprinkle const.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Trim headers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
- #if 0 the currently unused paired port linking and unlinking of dual
adapters.
- Simplify MSI/MSI-X allocation and release. For a single one, we don't need
to fiddle with the MSI/MSI-X count and pci_release_msi(9) is smart enough
to just do nothing in case of INTx.
- Canonicalize actions taken on attach failure and detach.
- Remove the remainder of incomplete support for older FreeBSD versions.
MFC after: 1 week
- Simplify MSI allocation and release. For a single one, we don't need to
fiddle with the MSI count and pci_release_msi(9) is smart enough to just
do nothing in case of INTx.
- Don't allocate MSI as RF_SHAREABLE.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Based on lessons learnt with dc(4) (see r185750), add bus space barriers to
the MII bitbang read and write functions as well as to instances of page
switching.
- Add missing locking to ed_ifmedia_{upd,sts}().
- Canonicalize some messages.
- Based on actual functionality, ED_TC5299J_MII_DIROUT should be rather named
ED_TC5299J_MII_DIRIN.
- Remove unused headers.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
