needed in later changes where we may not be able to lock the pic list lock
to perform a lookup, e.g. from within interrupt context.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
universal.
(1) New struct intr_map_data is defined as a container for arbitrary
description of an interrupt used by a device. Typically, an interrupt
number and configuration relevant to an interrupt controller is encoded
in such description. However, any additional information may be encoded
too like a set of cpus on which an interrupt should be enabled or vendor
specific data needed for setup of an interrupt in controller. The struct
intr_map_data itself is meant to be opaque for INTRNG.
(2) An intr_map_irq() function is created which takes an interrupt
controller identification and struct intr_map_data as arguments and
returns global interrupt number which identifies an interrupt.
(3) A set of functions to be used by bus drivers is created as well as
a corresponding set of methods for interrupt controller drivers. These
sets take both struct resource and struct intr_map_data as one of the
arguments. There is a goal to keep struct intr_map_data in struct
resource, however, this way a final solution is not limited to that.
(4) Other small changes are done to reflect new situation.
This is only first step aiming to create stable interface for interrupt
controller drivers. Thus, some temporary solution is taken. Interrupt
descriptions for devices are stored in INTRNG and two specific mapping
function are created to be temporary used by bus drivers. That's why
the struct intr_map_data is not opaque for INTRNG now. This temporary
solution will be replaced by final one in next step.
Differential Revision: https://reviews.freebsd.org/D5730
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
The ci20 port (by kan@) is going to reuse almost all of the intrng code
since the SoC in question looks suspiciously like someone took an ARM
SoC design and replaced the ARM core with a MIPS core.
* migrate out the code;
* rename ARM_ -> INTR_;
* rename arm_ -> intr_;
* move the interrupt flush routine from intr.c / intrng.c into
arm/machdep_intr.c - removing the code duplication and removing
the ARM specific bits from here.
Thanks to the Star Wars: The Force Awakens premiere line for allowing
me a couple hours of quiet time to finish the universe builds.
Tested:
* make universe
TODO:
* The structure definitions in subr_intr.c still includes machine/intr.h
which requires one duplicates all of the intrng definitions in
the platform code (which kan has done, and I think we don't have to.)
Instead I should break out the generic things (function declarations,
common intr structures, etc) into a separate header.
* Kan has requested I make the PIC based IPI stuff optional.
variable during mp_start() which is too late. Move this to mp_setmaxid()
where other architectures set it and move x86 assertions to MI code.
Reviewed by: kib (x86 part)
the name the function will have when the new ARM_INTRNG code is integrated,
and doing this rename first will make it easier to toggle the new interrupt
handling code on/off with a config option for debugging.
consumers can configure clock frequency
- Add ti_prcm_clk_set_source_freq wrapper for clk_set_source_freq
- Add am335x_clk_set_arm_disp_freq function to control pixel clock
frequency for LCD and HDMI output. Both of them are sensitive
to frequency skews and we need to get pixel clock matching requested
frequency as close to possible
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
to be present. Thsi creates a new per-SoC driver that handles probe and
setting/getting the gpio flags.
Differential Revision: https://reviews.freebsd.org/D943
Reviewed by: loos, rpaulo
MFC after: 1 week
description was eaten by the dog (or an editor crash or something).
Add variable-frequency support to the arm mpcore eventtimer driver.
This allows a platform's early init code to tell the mpcore driver that the
clock frequency can vary. That causes the mpcore driver to register an
eventtimer, but not a timecounter. The platform has to provide a time
counter using some other fixed-frequency clock, but can still use the
per-cpu goodness of the mpcore hardware for event timers.
When the platform support code does something to change the frequency of
the CPU clocks (power saving, thermal management) it must tell the mpcore
driver code about it using arm_tmr_change_frequency().
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.
Thanks to alc@ for pointing this out.
- Add pl310.disable tunable to disable L2 cache altogether. In
order to make sure that it's 100% disabled we use cache event
counters for cache line eviction and read allocate events
and panic if any of these counters increased. This is purely
for debugging purpose
- Direct access DEBUG_CTRL and CTRL might be unavailable in
unsecure mode, so use platform-specific functions for
these registers
- Replace #if 1 with proper erratum numbers
- Add erratum 753970 workaround
- Remove wait function for atomic operations
- Protect cache operations with spin mutex in order to prevent race condition
- Disable instruction cache prefetch and make sure data cache
prefetch is enabled in OMAP4-specific intialization
