so that code shared between imx5 and imx6 can work with OIDs under that node.
Add last_reset_status (integer) and last_reset_reason (string) OIDs that
provide info about the last chip reset (power-on, software reset, watchdog
timeout).
Replace tlb_flush_local() by tlb_flush() as even not global mappings
could be fetched to TLB(s) on other cores by speculative table walk.
From OS point of view, it was not a problem as either such mappings
were not used anymore or they were flushed from TLB(s) when reused.
However, from hardware point of view, it was a problem. Not flushed
mappings could be a target for speculative reads or prefetches (which
might be quite aggresive on ARM cores). As speculative read can fill
cacheline, it can cause a real problem, when physical page is reused,
but mapped with different memory attributes.
Anyhow, it's good to have only valid mappings in TLB(s).
Approved by: kib (mentor)
of the SRS (software reset) bit in the watchdog control register. Despite
what the manual seems to imply, this bit DOES trigger an immediate reset, as
opposed to simply flagging the type of reset as software-triggered.
created for bus_dma_tag_t tag, bounce pages should be allocated
only if needed.
Before the fix, they were allocated always if BUS_DMA_COULD_BOUNCE flag
was set but BUS_DMA_MIN_ALLOC_COMP not. As bounce pages are never freed,
it could cause memory exhaustion when a lot of such tags together with
their maps were created.
Note that there could be more maps in one tag by current design.
However BUS_DMA_MIN_ALLOC_COMP flag is tag's flag. It's set after
bounce pages are allocated. Thus, they are allocated only for first
tag's map which needs them.
Approved by: kib (mentor)
Drivers can request DMA to buffers that are not in memory represented
in the vm page arrays. Because of this, store KVA of already mapped
buffer to synclist and use it in dma_dcache_sync().
Reviewed by: jah
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D4120
This structure must be binary compatible regardless of PMAP
version being used. Create reserved section for NEW_PMAP to
make other variables be placed exactly in the same memory
addresses. This fixes kgdb/gdb behavoiur, which uses pcb.h stuctures.
The NEW_PMAP is kernel flag, so it does not propagate to the buildworld,
what makes the tools using pcb.h unable to parse PCB data.
Reviewed by: mmel, kib
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4011
Use proper size of exynos_ehci_softc, not the generic one.
Reviewed by: andrew
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4189
Zybo needs its own DTB and has a different PHY, so add it to
the base kernel. Details on building bootable SD images at
http://www.thomasskibo.com/zedbsd/
Submitted By: Thomas Skibo
since it isn't used for my application. Add back the md device since
it's needed for NanoBSD support. Add in many of the small memory
footprint options from the access points.
With these changes we go from having ~8MB to having ~20MB free,
though free + inactive only goes from ~35MB to ~42MB. We can
also boot a nanobsd image mostly (I had to hand tweak what was
built to represent the final goal).
Move the FDT stuff to the top. We're almost ready to pull the trigger
to moving over to FDT, but something in the MCI driver is freaking out
when we do and that needs fixing first.
Allow manipulation with PSR_A bit on ARMv6+.
Remove declaration of unused functions.
This effectively enables asynchronous aborts on early bootstrap stage,
which previously was not enabled due to an error in enable_interrupts().
PR: 201434
Reported by: Gregory Soutade <soutade at gmail.com>
Approved by: kib (mentor)
function which checks an address for privileged (PL1) write access.
The function is inlined so it does not bring any cost, but makes
function set for checking privileged access complete.
Approved by: kib (mentor)
little-endian configuration for 64-bit variant is supported.
Reviewed by: mmel
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D4113
- boot page table is not allocated in data section, so must be
cleared before use
- map only one section (1 MB) for SOCDEV mapping (*)
- DSB must be used for ensuring of finishing TLB operations
- Invalidate BTB when appropriate
PR: 198360
Reported by: Daisuke Aoyama <aoyama at peach.ne.jp> (*)
Approved by: kib (mentor)
as of r288992 use it to manage the CCNT.
Use the CNNT for get_cyclecount() instead of binuptime() when device pmu
is compiled in; if it fails to attach, fall back to the former method.
Enable by default for the BeagleBoneBlack configuration.
Optained from: Cambridge/L41
Sponsored by: DARPA/AFRL
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3837
variable during mp_start() which is too late. Move this to mp_setmaxid()
where other architectures set it and move x86 assertions to MI code.
Reviewed by: kib (x86 part)
"rmii", use rmii mode for the MAC, otherwise use MII mode. The code is
somewhat duplicated between these drivers for this.
Also, add AT91RM9200 compatibility strings to the ate driver. In the
future, there's a good chance that ate will lose the MACB support and
only attach to the AT91RM9200 EMAC device since the macb works now
that RMII support has been added to it.
driver. This is taken from the MAC at boot, but can be overridden with
'options AT91_MACB_USE_RMII'.
Switch to macb for HL201 and SAM9G20EK boards. It now works both
places. Also start to sneak up on FDT for the SAM9G20EK board, but
leave disabled due to issues with MMC that haven't been resolved.
Add early debug support for the SAM9G20EK since that is required
for FDT to work presently on these SoC.
