- redo the "at" configuration system so that it just syntax checks
to make sure the device you're configuring something "at" appears to
exist. Nuke a bunch of complexity that was responsible for creating
"clones" of wildcard devices and some wierd stuff in a few places
including the scbus config tables etc.
- merge "controller" and "device" - there is no difference as far as
the kernel is concernend, it's just something there to make life
difficult for config file writers. "controller" is now an alias for
"device".
- emit full scsi config into the resource tables. We could trivially
change cam to use that rather than it's own "special" table for wiring
and static configuration. ATA could use this too for static wiring.
- try and emulate some of the quirks of the old system where it made
sense. Some were too strange though and I'd be very suprised if they
were features and not outright bugs. nexus handling is still strange.
One thing in particular is that some of the wierd entries in the
newbus devtables is now gone as it was a quirk side effect of the
wildcard/question-mark cloning above.
GENERIC and LINT still build etc.
${GEN_CFLAGS} and -U_KERNEL became negative when all all the
genassym.c's were converted to be cross-built.
Makefile.*:
- Cleanups associated with the old genassym.
- Fixed deprecated spelling of ${.IMPSRC} as "$<".
known option, unknown options following the known option were not
removed. Now I think only unknown options in unknown options files
are not removed. This is harmless because unknown options files should
not be used, but removing the files would be cleaner.
now you can dynamically create rate-limited queues for different
flows using masks on dst/src IP, port and protocols.
Read the ipfw(8) manpage for details and examples.
Restructure the internals of the traffic shaper to use heaps,
so that it manages efficiently large number of queues.
Fix a bug which was present in the previous versions which could
cause, under certain unfrequent conditions, to send out very large
bursts of traffic.
All in all, this new code is much cleaner than the previous one and
should also perform better.
Work supported by Akamba Corp.
It seems that the IDE system uses 0x3f6 for itself, which conflicts with
fdc's default 0x3f0-3f7 allocation range. Sigh. Work around this.
Use bus_set_resource() rather than allocating specific areas, it makes
the code a little cleaner.
Based on work by: dfr
Note: the .INF file for LinkSys's driver says the vendor ID is 0x66b,
however this does not agree with the vendor ID listed for LinkSys in
the company list from www.usb.org. In fact, 0x66b doesn't seem to appear
in the company list at all. Furthermore, this same vendor ID crops
up in some of the D-Link .INF files. Frankly I don't know what the heck
is going on here, but I need to add 0x66b to usbdevs and call it
something, so here we are.
certain PHY addresses in aue_miibus_readreg(). Not all adapters based
on the Pegasus chip may have their PHYs wired for the same MII bus
addresses: the logic that I used for my ADMtek eval board might not
apply to other adapters, so make sure to only use it if this is really
an ADMtek eval board (check the vendor/device ID).
This will hopefully make the LinkSys USB100TX adapter work correctly.
makes it a little easier to notice that parity checking an 8bit sram
isn't working.
Turn on scb and internal data-path parity checking for all pci chips types.
We were only doing this for ultra2 chips.
After clearing the parity interrupt status, clear the BRKADRINT. This
avoids seeing a bogus BRKADRINT interrupt after external SCB probing
once normal interrupts are enabled.
an URB before sending ZLP) set to the default. Choosing a bad value
can apparently cause a lockup on some machines/controllers.
Reported by: Doug Ambrisko
93cx6.c:
Make the SRAM dump output a little prettier.
aic7xxx.c:
Store all SG entries into our SG array in kernel space.
This makes data-overrun and other error reporting more
useful as we can dump all SG entries. In the past,
we only stored the SG entries that the sequencer might
need to access, which meant we skipped the first element
that is embedded into the SCB.
Add a table of chip strings and replace ugly switch
statements with table lookups.
Add a table with bus phase strings and message reponses
to parity errors in those phases. Use the table to
pretty print bus phase messages as well as collapse
another switch statement.
Fix a bug in target mode that could cause us to unpause
the sequencer early in bus reset processing.
Add the 80MHz/DT mode into our syncrate table. This
rate is not yet used or enabled.
Correct some comments, clean up some code...
aic7xxx.h:
Add U160 controller feature information.
Add some more bit fields for various SEEPROM formats.
aic7xxx.reg:
Add U160 register and register bit definitions.
aic7xxx.seq:
Make phasemis state tracking more straight forward. This
avoids the consumption of SINDEX which is a very useful register.
For the U160 chips, you must use the 'mov' instruction to
update DFCNTRL. Using 'or' to set the PRELOADED bit is
completely ineffective.
At the end of the command phase, wair for our ACK signal
to de-assert before disabling the SCSI dma engine. For
slow devices, this avoids clearing the ACK before the
other end has had a chance to see it and lower REQ.
controllers will run at U2 speeds until I can complete the U160 support
for this driver.
Correct a termination buglet for the 2940UW-Pro.
Be more paranoid in how we probe and enable external ram, fast external
ram timing and external ram parity checking. We should now work on
20ns and 8bit SRAM parts.
Perform initial setup for the DT feature on cards that support it.
Factorize and clean up code. Use tables where it makes sense, etc.
Add some delays in dealing with the board control logic. I've never
seen this code fail, but with the ever increasing speed of processors,
its better to insert deterministic delays just to be safe. This stuff
is only touched during probe and attach, so the extra delay is of no
concern.
ethernet adapters that are supported by the aue and kue drivers.
There are actually a couple more out there from Accton, Asante and
EXP Computer, however I was not able to find any Windows device
drivers for these on their servers, and hence could not harvest
their vendor/device ID info. If somebody has one of these things
and can look in the .inf file that comes with the Windows driver,
I'd appreciate knowing what it says for 'VID' and 'PID.'
Additional adapters include: the D-Link DSB-650 and DSB-650TX, the
SMC 2102USB, 2104USB and 2202USB, the ATen UC10T, and the Netgear EA101.
These are all mentioned in the man pages, relnotes and LINT.
Also correct the date in the kue(4) man page. I wrote this thing
on Jan, 4 2000, not 1999.
. add Xrs to hosts.equiv(5), auth.conf(5), services(5) to some pages
. sort Xrs in SEE ALSO sections
Patches based on PR: docs/15680
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
