controller with Card Read Host Controller. These controllers are
multi-function devices and have the same ethernet core of
JMC250/JMC260. Starting from REVFM 5(chip full mask revision)
controllers have the following features.
o eFuse support
o PCD(Packet Completion Deferring)
o More advanced PHY power saving
Because these controllers started to use eFuse, station address
modified by driver is permanent as if it was written to EEPROM. If
you have to change station address please save your controller
default address to safe place before reprogramming it. There is no
way to restore factory default station address.
Many thanks to JMicron for continuing to support FreeBSD.
HW donated by: JMicron
a 2GHz channel with appropriate flags set to sc->config. Due to not zeroing
sc->config for auth/assoc those flags are still set while trying to connect
on a 5GHz channel.
MFC after: 3 days
Use pci_enable_busmaster instead of setting PCIM_CMD_BUSMASTEREN
directly. There's no need to set PCIM_CMD_MEMEN. The bit is set when a
SYS_RES_MEMORY resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Write 1 byte instead of 4 when setting the HIFN_TRDY_TIMEOUT register.
It is only 1 byte according to the specification.
Reviewed by: jhb
Approved by: kib (mentor)
configuration registers directly.
Remove pci_enable_io calls where they are redundant. The PCI bus driver
will set the right bits when the corresponding bus resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Reviewed by: jhb
Approved by: kib (mentor)
experimental NFSv4 server. The first was a bogus use of VOP_ISLOCKED()
in a KASSERT() and the second was the need to lock the vnode for the
nfsrv_checkremove() call. Also, delete a "__unused" that was bogus,
since the argument is used.
Reviewed by: zack.kirsch at isilon.com
MFC after: 2 weeks
In this case we call target function only on a single CPU and do not
need any synchronization at the setup stage.
It's a bit non-obvious but setup function of NULL means that
smp_rendezvous_cpus waits for all CPUs to arrive at the rendezvous
point, but without doing any actual setup. While using
smp_no_rendevous_barrier means that each CPU proceeds on its own
schedule without any synchronization whatsoever.
MFC after: 3 weeks
earlier commit. While here, move the thread lock down in rtp_to_pri().
It is not needed for all of the priority value checks and the computation
of newpri.
Reported by: swell.k @ gmail
MFC after: 3 days
This is based on the patch submitted by Yuri Skripachov.
Overview of the changes:
- clarify double-use of some ACPI_BATT_STAT_* definitions
- clean up undefined/extended status bits returned by _BST
- warn about charging+discharging bits being set at the same time
PR: kern/124744
Submitted by: Yuri Skripachov <y.skripachov@gmail.com>
Tested by: Yuri Skripachov <y.skripachov@gmail.com>
MFC after: 2 weeks
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.
delete the IRQ resource from the psmcpnp device completely.
- Don't allocate the IRQ resource shared. It is not a shareable interrupt
on ISA. The bus driver can set RF_SHAREABLE if the IRQ is actually
shareable on a non-ISA bus.
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
- Remove the -shared flag for the trampoline binary, generate an
ELF executable instead of a shared object.
- No need to generate tmphack.S, move the code to sys/mips/mips/inckern.S
- No need generate opt_kernname.h, KERNNAME can be passed with -D
Reviewed by: gonzo, imp
Keep three lines disabled which I am unsure if they had been used at all.
This will allow us to seek testers and possibly bring it all back.
Discussed with: rwatson
MFC after: 7 weeks
a 32-bit one. This can cause weird timeout issues, as the copying reads
garbage from the user.
Code by: Deepak Veliath <deepak dot veliath at isilon dot com>
MFC after: 1 week
in devfs_vmkdir() while adding the entry to de_list of the parent.
- Apply devfs rules to newly created directories and symbolic links.
PR: kern/125034
Submitted by: Mateusz Guzik (original version)
function always returned the nominal frequency instead of current frequency
because we use RDTSC instruction to calculate difference in CPU ticks, which
is supposedly constant for the case. Now we support cpu_get_nominal_mhz()
for the case, instead. Note it should be just enough for most usage cases
because cpu_est_clockrate() is often times abused to find maximum frequency
of the processor.
