Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
- Add data structuress for doing 64-bit scatter/gather
- Move busdma tag creations around so that only the parent is
created in aac_pci.c.
- Retrieve the capabilities word from the firmware before setting
up command structures and tags. This allows the driver to decide
whether to do 64-bit commands, and if work-arounds are needed for
systems with >2GB of RAM.
- Only enable the SCSI passthrough if it's enabled in the capabilities
word in the firmware.
This should fix problems with the 2120S and 2200S cards in systems with more
than 2GB of RAM. Full 64-bit support is forthcoming.
MFC-After: 1 week
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
- the mutex aac_io_lock protects the main codepaths which handle queues and
hardware registers. Only one acquire/release is done in the top-half and
the taskqueue. This mutex also applies to the userland command path and
CAM data path.
- Move the taskqueue to the new Giant-free version.
- Register the disk device with DISKFLAG_NOGIANT so the top-half processing
runs without Giant.
- Move the dynamic command allocator to the worker thread to avoid locking
issues with bus_dmamem_alloc().
This gives about 20% improvement in most of my benchmarks.
field for holding driver-dependant data. Instead of putting the pointer
to the driver command struct in there, take advantage of these structs
being a (virtually) contiguous array and just put the array index in the
field.
retain symetry with aac_alloc_commans(). Since aac_alloc_commands()
allocates fib maps and places them onto the fib lists, aac_free_commands()
should reverse those operations.
o Combine two ifs with the same body with an ||.
o Switch from uintptr_t to uint32_t for fib map load operations.
The target is a uint32_t so using this type for the map load call
avoids an extra cast. uintptr_t should only be used when you need
an "int sized the same as the machine's poitner size" which is not
the case here.
o Removed the commented out M_WAITOK flag in the allocation in
aac_alloc_commands(). The kernel will only block in the allocator
if it can grow the size of the kernel. This usually results in a
page-out which could involve this aac device. Thus, sleeping here
could deadlock the machine. Assuming this operation is occurring outside
of attach time, we have enough fibs to operate anyway, so waiting for
fibs to free up is okay if not optimal.
o In aac_alloc_commands(), if we cannot dmamem_alloc additional fib
space, free the fib map.
o In aac_alloc_commands(), if we cannot create per-command dmamaps, don't
lose track of the fib map that is mapping all of the commands that we
have already released into the free pool. Instead, just cut out of
the loop and modify aac_free_commands to not attempt to free maps that
have not been allocated.
o Don't use a magic number when pre-allocating fibs.
o Use PAGE_SIZE to allocate in page sized chunks instead of an
architecture specific constant.
Submitted by: gibbs
blocks now, which should eliminate problems with the driver failing to
attach due to insufficient contiguous RAM. Allow the FIB pool to grow
from the default of 128 to the max of 512 as demand grows. Also pad the
adapter init struct to work around the 2120/2200 DMA bug now that there
is no longer a FIB slab.
- Move the command timeout check from a separate repeating timeout to the
kthread since the kthread is already running periodically.
- Move printing the hardware print buffer to the kthread.
- Properly shut down the kernel thread on detach.
- Detach the child array devices on detach.
- Don't issue a controller halt command on detach. Doing so requires a PCI
reset to wake the controller back up. The driver can now be unloaded as
long as CAM support is not enabled.
Rename diskerr() to disk_err() for naming consistency.
Drop the by now entirely useless struct disklabel argument.
Add a flag argument for new-line termination.
Fix a couple of printf-format-casts to %j instead of %l.
Correctly print the name of all bio commands.
Move the function from subr_disklabel.c to subr_disk.c,
and from <sys/disklabel.h> to <sys/disk.h>.
Use the new disk_err() throughout, #include <sys/disk.h> as needed.
Bump __FreeBSD_version for the sake of the aac disk drivers #ifdefs.
Remove unused disklabel members of softc for aac, amr and mlx, which seem
to originally have been intended for diskerr() use, but which only rotted
and got Copy&Pasted at least two times to many.
Sponsored by: DARPA & NAI Labs.
ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
check is complicated by the fact that the Adaptec 5400S cards claim to use
1.x firmware also. PERC2/QC 1.x firmware is not compatible with this driver
and will cause a system hang.
MFC after: 3 days
released management apps.
1. Implement poll(). This will check for queued aif's so that a
subsequent ioctl call to retrieve the next aif will not block.
2. Don't catch signals when sleeping on a fib sent from userland. This
causes a race and panic due to the pthread context switcher waking
up the tsleep at inopportune times.
3. Fix some whitespace nits.
MFC after: 3 days
1. Correctly handle commands initiated by the adapter. These commands
are defered to a kthread responsible for their processing, then are
properly returned to the controller.
2. Add/remove disk devices when notified by the card that a container was
created/deleted/offline.
3. Implement crashdump functionality.
4. Support all ioctls needed for the management CLI to work. The linux
version of this app can be found at the Dell or HP website. A native
version will be forthcoming.
MFC-after: 4.4-RELEASE
interrupt handler from the upper half, etc. This fixes some serious stability
problems that we were seeing on our production server. These patches have
been tested for almost 6 months and are a highly recommended MFC candidate.
Reviewed by: gibbs, merry, msmith
MFC after: 4 days
Add the AAC_DEBUG option to enable debugging in the aac driver.
Correct a race condition in the interrupt handler where the
controller may queue a fib to a response queue after the driver
has serviced the queue but before the interrupt is cleared.
This could leave a completed fib stranded in the response queue
unless another I/O completed and generated another interrupt.
Reviewed by: msmith
with the driver locking up under load.
- Restructure so that we use a static pool of commands/FIBs, rather than
allocating them in clusters. The cluster allocation just made things
more complicated, and allowed us to waste more memory in peak load
situations.
- Make queueing macros more like my other drivers. This adds queue stats
for free. Add some debugging to take advantage of this.
- Reimplement the periodic timeout scan. Kick the interrupt handler
and the start routine every scan as well, just to be safe. Track busy
commands properly.
- Bring resource cleanup into line with resource allocation. We should
now clean up correctly after a failed probe/unload/etc.
- Try to start new commands when old ones are completed. We weren't doing
this before, which could lead to deadlock when the controller was full.
- Don't try to build a new command if we have found a deferred command.
This could cause us to lose the deferred command.
- Use diskerr() to report I/O errors.
- Don't bail if the AdapterInfo structure is the wrong size. Some variation
seems to be normal. We need to improve our handing of 2.x firmware sets.
- Improve some comments in an attempt to try to make things clearer.
- Restructure to avoid some warnings.
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
