doing suspend check. This restores the pre-r251684 behaviour, to
retry once after the signal is detected.
PR: kern/192918
Submitted by: Elliott Rabe, Dell Inc., Eric van Gyzen <eric@vangyzen.net>
Obtained from: Dell Inc.
MFC after: 1 week
- Retire long time unused (basically always unused) sys__umtx_lock()
and sys__umtx_unlock() syscalls
- struct umtx and their supporting definitions
- UMUTEX_ERROR_CHECK flag
- Retire UMTX_OP_LOCK/UMTX_OP_UNLOCK from _umtx_op() syscall
__FreeBSD_version is not bumped yet because it is expected that further
breakages to the umtx interface will follow up in the next days.
However there will be a final bump when necessary.
Sponsored by: EMC / Isilon storage division
Reviewed by: jhb
- When looping, check for the pending suspension. Otherwise, other
usermode thread which races with the looping one, could try to
prevent the process from stopping or exiting.
- Add missed checks for the faults from casuword*(). The code is
structured in a way which makes the loops exit if the specified
address is invalid, since both fuword() and casuword() return -1 on
the fault. But if the address is mapped readonly, the typical value
read by fuword() is different from -1, while casuword() returns -1.
Absent the checks for casuword() faults, this is interpreted as the
race with other thread and causes non-interruptible spinning in the
kernel.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Programs often do not expect an [EINTR] return from sem_wait() and POSIX
only allows it if the signal was installed without SA_RESTART. The timeout
in sem_timedwait() is absolute so it can be restarted normally.
The umtx call can be invoked with a relative timeout and in that case
[ERESTART] must be changed to [EINTR]. However, libc does not do this.
The old POSIX semaphore implementation did this correctly (before r249566),
unlike the new umtx one.
It may be desirable to avoid [EINTR] completely, which matches the pthread
functions and is explicitly permitted by POSIX. However, the kernel must
return [EINTR] at least for signals with SA_RESTART clear, otherwise pthread
cancellation will not abort a semaphore wait. In this commit, only restore
the 8.x behaviour which is also permitted by POSIX.
Discussed with: jhb
MFC after: 1 week
UMTX_PROFILING should really analyze the distribution of locks as they
index entries in the umtxq_chains hash-table.
However, the current implementation does add/dec the length counters
for *every* thread insert/removal, measuring at all really userland
contention and not the hash distribution.
Fix this by correctly add/dec the length counters in the points where
it is really needed.
Please note that this bug brought us questioning in the past the quality
of the umtx hash table distribution.
To date with all the benchmarks I could try I was not able to reproduce
any issue about the hash distribution on umtx.
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff, davide
MFC after: 2 weeks
- Use u_int values for length and max_length values
- Add a way to reset the max_length heuristic in order to have the
possibility to reuse the mechanism consecutively without rebooting
the machine
- Add a way to quick display top5 contented buckets in the system for
the max_length value.
This should give a quick overview on the quality of the hash table
distribution.
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff, davide
application destroys semaphore after sem_wait returns. Just enter
kernel to wake up sleeping threads, only update _has_waiters if
it is safe. While here, check if the value exceed SEM_VALUE_MAX and
return EOVERFLOW if this is true.
a mutex after a thread has unlocked it, it event writes data to the mutex
memory to clear contention bit, there is a race that other threads
can lock it and unlock it, then destroy it, so it should not write
data to the mutex memory if there isn't any waiter.
The new operation UMTX_OP_MUTEX_WAKE2 try to fix the problem. It
requires thread library to clear the lock word entirely, then
call the WAKE2 operation to check if there is any waiter in kernel,
and try to wake up a thread, if necessary, the contention bit is set again
by the operation. This also mitgates the chance that other threads find
the contention bit and try to enter kernel to compete with each other
to wake up sleeping thread, this is unnecessary. With this change, the
mutex owner is no longer holding the mutex until it reaches a point
where kernel umtx queue is locked, it releases the mutex as soon as
possible.
Performance is improved when the mutex is contensted heavily. On Intel
i3-2310M, the runtime of a benchmark program is reduced from 26.87 seconds
to 2.39 seconds, it even is better than UMTX_OP_MUTEX_WAKE which is
deprecated now. http://people.freebsd.org/~davidxu/bench/mutex_perf.c
according to POSIX document, the clock ID may be dynamically allocated,
it unlikely will be in 64K forever. To make it future compatible, we
pack all timeout information into a new structure called _umtx_time, and
use fourth argument as a size indication, a zero means it is old code
using timespec as timeout value, but the new structure also includes flags
and a clock ID, so the size argument is different than before, and it is
non-zero. With this change, it is possible that a thread can sleep
on any supported clock, though current kernel code does not have such a
POSIX clock driver system.
UMTX_OP_WAIT. Upper 16bits is enough to hold a clock id, and lower
16bits is used to pass flags. The change saves a clock_gettime() syscall
from libthr.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
use sched_lend_user_prio to set lent priority.
- Improve pthread priority-inherit mutex, when a contender's priority is
lowered, repropagete priorities, this may cause mutex owner's priority
to be lowerd, in old code, mutex owner's priority is rise-only.
- Add flags CVWAIT_ABSTIME and CVWAIT_CLOCKID for umtx kernel based
condition variable, this should eliminate an extra system call to get
current time.
- Add sub-function UMTX_OP_NWAKE_PRIVATE to wake up N channels in single
system call. Create userland sleep queue for condition variable, in most
cases, thread will wait in the queue, the pthread_cond_signal will defer
thread wakeup until the mutex is unlocked, it tries to avoid an extra
system call and a extra context switch in time window of pthread_cond_signal
and pthread_mutex_unlock.
The changes are part of process-shared mutex project.
a 32-bit one. This can cause weird timeout issues, as the copying reads
garbage from the user.
Code by: Deepak Veliath <deepak dot veliath at isilon dot com>
MFC after: 1 week
It is possible a lower priority thread lending priority to higher priority
thread, in old code, it is ignored, however the lending should always be
recorded, add field td_lend_user_pri to fix the problem, if a thread does
not have borrowed priority, its value is PRI_MAX.
MFC after: 1 week
rwlock to protect the table. In old code, thread lookup is done with
process lock held, to find a thread, kernel has to iterate through
process and thread list, this is quite inefficient.
With this change, test shows in extreme case performance is
dramatically improved.
Earlier patch was reviewed by: jhb, julian
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
Reviewed by: kib, jhb
