I guess that means that microcode update has never worked for AMD CPUs.
Please also note that only older AMD CPUs and micrcode file format are
supported anyway (pre 10h family).
MFC after: 1 week
Interface routes are refcounted as packets move through the stack,
and there's garbage collection tied to it so that route changes can
safely propagate while traffic is flowing. In our setup, we weren't
changing or deleting any routes, but the refcounting logic in
ip6_input() was wrong and caused a reference leak on every inbound
V6 packet. This eventually caused a 32bit overflow, and the resulting
0 value caused the garbage collection to run on the active route.
That then snowballed into the panic.
Reviewed by: scottl
MFC after: 3 days
- Make the device description match the driver name.
- Identify the chip variant based on the JEDEC and use that information
to use the proper values for page count, offset and size instead of
hardcoding a AT45DB642x with 2^N byte page support disabled.
- Take advantage of bioq_takefirst().
- Given that CONTINUOUS_ARRAY_READ_HF (0x0b) command isn't even mentioned
in Atmel's DataFlash Application Note, as suggested by the previous
comment may not work on all all devices and actually doesn't properly
on at least AT45DB321D (JEDEC 0x1f2701), rewrite at45d_task() to use
CONTINUOUS_ARRAY_READ (0xe8) for reading instead. This rewrite is laid
out in a way allowing to easily add support for BIO_DELETE later on.
- Add support for reads and writes not starting on a page boundary.
- Verify the flash content after writing.
- Let at45d_task() gracefully handle errors on SPI transfers and the
device not becoming ready afterwards again. [1]
- Use DEVMETHOD_END. [1]
- Use NULL instead of 0 for pointers. [1]
Additional testing by: Ian Lepore
Submitted by: Ian Lepore [1]
MFC after: 1 week
- Move DMA tag and map creature to at91_spi_activate() where the other
resource allocation also lives. [1]
- Flesh out at91_spi_deactivate(). [1]
- Work around the "Software Reset must be Written Twice" erratum.
- For now, run the bus at the slowest speed possible in order to work
around data corruption on transit even seen with 9 MHz on ETHERNUT5
(15 MHz maximum) and AT45DB321D (20 MHz maximum). This also serves as
a poor man's work-around for the "NPCSx rises if no data data is to be
transmitted" erratum of RM9200. Being able to use the appropriate bus
speed would require:
1) Adding a proper work-around for the RM9200 bug consisting of taking
the chip select control away from the SPI peripheral and managing it
directly as a GPIO line.
2) Taking the maximum frequencies supported by the actual board and the
slave devices into account and basing the whole thing on the master
clock instead of hardcoding a divisor as previously done.
3) Fixing the above mentioned data corruption.
- KASSERT that TX/RX command and data sizes match on transfers.
- Introduce a mutex ensuring that only one child device is running a SPI
transfer at a time. [1]
- Add preliminary, #ifdef'ed out support for setting the chip select. [1]
- Use the RX instead of the TX commando size when setting up the RX side
of a transfer.
- For controllers having SPI_SR_TXEMPTY, i.e. !RM9200, also wait for the
completion of the TX part of transfers before stopping the whole thing
again.
- Use DEVMETHOD_END. [1]
- Use NULL instead of 0 for pointers. [1, partially]
Additional testing by: Ian Lepore
Submitted by: Ian Lepore [1]
MFC after: 1 week
locked xchg instruction. IA32 memory model guarantees that store has
release semantic, since stores cannot pass loads or stores.
Reviewed by: bde, jhb
Tested by: pho
MFC after: 2 weeks
The stat structures returned on pipes seems to contain all the
information required by POSIX. Especially the wording "and thus to a
pipe" makes little sense, because it seems to imply a certain
relationship between sockets and pipes that simply isn't there.
MFC after: 2 weeks
Make the default role NONE if target mode is selected. This
allows ctl(8) to switch to/from target mode via knob settings.
If we default to role 'none', this causes a reset of the
24XX f/w which then causes initiators to wake up and notice
when we come online.
Reviewed by: kdm
MFC after: 2 weeks
Sponsored by: Spectralogic
figure out domain, etc..
Zero ATIO and INOTify allocations. It makes for much
less guesswork when looking at the structure and
seeing 'deadc0de' present.
Reviewed by: kdm
MFC after: 2 weeks
Sponsored by: Spectralogic
Currently this dumps the status of any error bits in the PCI status register
and PCI-express device status register. It also lists any errors indicated
by version 1 of PCI-express Advanced Error Reporting (AER).
MFC after: 1 week
Add source of documentation for this driver.
Thanks to Warren Block for the suggestions for readability.
Note that strict_rx_mtu in inverted in stable/7/8/9 and is
named loose_rx_mtu. Ensure that this is converted over when MFC'd
hw.bce.rx_ticks
hw.bce.rx_ticks_int
hw.bce.rx_quick_cons_trip
hw.bce.rx_quick_cons_trip_int
hw.bce.tx_ticks
hw.bce.tx_ticks_int
hw.bce.tx_quick_cons_trip
hw.bce.tx_quick_cons_trip_int
hw.bce.strict_rx_mtu
hw.bce.hdr_split
hw.bce.tx_pages
hw.bce.rx_pages
hw.bce.tso_enable
hw.bce.verbose
Reviewed by: Warren Block <wblock@wonkity.com>
MFC after: 3 days
to SYSINIT routines if they can be resolved via symbol look up in DDB.
To avoid false positives, only honor a name if the symbol resolves
exactly to the pointer value (no offset).
MFC after: 1 week
