- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
consumers can configure clock frequency
- Add ti_prcm_clk_set_source_freq wrapper for clk_set_source_freq
- Add am335x_clk_set_arm_disp_freq function to control pixel clock
frequency for LCD and HDMI output. Both of them are sensitive
to frequency skews and we need to get pixel clock matching requested
frequency as close to possible
charger configuration and provide some basic control knobs to
set charger voltage and dump config on boot. Two loader tunables
have been added:
o hw.am335x_pmic.bootverbose set to 1 to get more info on the
boot;
o hw.am335x_pmic.vo: set to charger voltage to be applied on
kernel initialization time, supported values are "4.10V",
"4.15V", "4.20V" and "4.25V".
Cleanup code a bit in general, move TPS65217 register
definitions into a separate header, convert bit-banging
defines into bitmap structures.
Also threat the case when power source is neither "AC" nor "USB"
as "Battery", not "Unknown".
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
ntpd is hard-coded to use /dev/ppsN, and typically when multiple PPS sources
are available the sysadmin will symlink the right one(s) to /dev/ppsN, so
it's best to not usurp those names directly.
both the post-filter and post-thread callbacks.
Also eliminate a completely unecessary write to INTC_ISR_CLEAR register,
which clears a software-generated interrupt that can only happen with a
write to INTC_ISR_SET (which nothing does).
The DISP DPLL clock is slower and was making the PRU programs slower
on FreeBSD than on Linux.
Submitted by: Manuel Stuehn <freebsdnewbie at freenet.de>
MFC after: 1 week
Minimum LCDC is 2 so clock freq shouild be 2*max_pixel_clock. Maximum pixel
clock for HDMI is 148500 (1920x1080). But AM335x can not run in this mode
due to bandwidth and clock limitations
1 second is not enugh for TDA19988 HDMI framer (e.g. on Beaglebone Black)
- Add per-device i2c_timout sysctl (dev.iichb.X.i2c_timeout) to control
I2C bus timeout manually
- Pass softc instead of device_t to all sysctl handlers
While in theory this should have been a transparent change (and was for all
other drivers), cpsw(4) never used the proper accessor macros in a few
places but spelt the indirect m_hdr.mh_* out itself. Convert those to
use m_len and m_data and unbreak the driver build.
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
According to http://e2e.ti.com/support/arm/sitara_arm/f/791/t/210729 the
USB reset pulse has an undocumented duration of 200ns and during this
period the module must not be acessed.
We wait for 100us to take into account for some imprecision of the early
DELAY() loop.
This fixes the eventual 'External Non-Linefetch Abort (S)' that happens at
boot while resetting the musb subsystem.
While here, enable the USB subsystem clock before the first access.
Discussed with: ian, adrian
MFC after: 2 weeks
