detailed information under the sound debug. To make it easier accessible,
export that information through the set of sysctls like dev.hdaa.X.nidY.
Also tune some output to make it both more compact and informative.
from HDMI/DisplayPort devices in form of general connection status and
sound(4)-style channel matrix. Now that information is only reported in
readable form to verbose logs, but potentially could be used by sound(4)
to correctly choose default devices and configure vchans.
Fix rear and side channels swap on analog 7.1 outputs. As soon as there is
a huge mess in industry about naming and using of these channels, duplicate
rear channels of 4 and 5.1 streams to both read and side speakers.
if unused in that configuration mixer at NID 15 is muted. Probably CODEC
incorrectly reports its internal connections. Hide that muter from the
driver to avoid muting and make built-in speaker work.
There are several different CODECs sharing this ID and I have not enough
information about them and the bug to implement more universal solution.
Tested by: Big Yuuta <init.py@gmail.com>
MFC after: 2 weeks
with the real value in regular way if sensing is supported. This fixes
minor inconsistency when playback redirection appeared in undefined state
on boot if headphones were not connected.
device drivers that used to provide this feature.
This is a subset of 241856 (which was reverted)
Reviewed by: des
Approved by: cperciva (implicit)
MFC after: 1 week
make analog input loopback and dual-stream playback work by enabling
signal mixing by nid 22, as it should be according to info returned by
the CODEC. Otherwise pin nid 28 receives only signal from DAC nid 16.
PR: kern/169124
MFC after: 1 week
at r230551.
Also while there, make sense polling use reported for each node separately
instead of reporting accumulated total status.
Submitted by: Barbara <barbara.freebsd@gmail.com> (1)
MFC after: 3 days
names to shorten them. PulseAudio reported to have problems with names
longer then 63 chars and at least in XMMS long names are inconvinient.
Reported by: hselasky
MFC after: 3 days
The cs driver requires a table with firmware values. An
alternative firmware is available in a similar Open Sound
System driver. This is actually a partial revert of
Revision 77504.
Special thanks to joel@ for patiently testing several
replacement attempts.
The csa driver and the complete sound system are now free
of the GPL.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
Remove unneeded temporary variable (data) to better match the OSS code.
Remove some unused constants and type definitions.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
- add "+HP" in case of headphones redirection;
- add device type for analog devices, if all pins have the same.
As result now it may look like "Analog 5.1+HP/2.0" or "Front Analog Mic".
I hope it will be more useful than long and confusing.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
(HDMI and HBR bits set) and needed (AC3 format used with 8 channels).
This should allow DTS-HD/TrueHD pass-through with rates above 6.144Mbps.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
widgets. I am not sure if S/PDIF supports 32bit samples, but my Marantz
SR4001 doesn't, producing only single clicks on playback start/stop.
Because HDA controller requires 32bit alignment for all samples above 16bit,
we can't handle this situation in regular way and have to set 32bit format
in sound(4) for anything above 16bit. To workaround the problem, prefer
to setup hardware to use 24/20bit samples when 32bit format requested. Add
dev.pcm.X.play.32bit and dev.pcm.X.rec.32bit sysctls to control what format
really use for 32bit samples.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
maximal from 64K to 256K.
We usually don't need 750 sound interrupts per second (1.3ms latency)
when playing 192K/24/8 stream. 187 should be better. On usual 48K/16/2
it is just enough for hw.snd.latency=9 at hw.snd.latency_profile=1 with
23 and 6 interrupts per second.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Previous code was relatively dumb. During CODEC probe it was tracing signals
and statically binding amplifier controls to the OSS mixer controls. To set
volume it just set all bound amplifier controls proportionally to mixer
level, not looking on their hierarchy and amplification levels/offsets.
New code is much smarter. It also traces signals during probe, but mostly
to find out possible amplification control rages in dB for each specific
signal. To set volume it retraces each affected signal again and sets
amplifiers controls recursively to reach desired amplification level in dB.
It would be nice to export values in dB to user, but unluckily our OSS mixer
API is too simple for that.
As result of this change:
- cascaded amplifiers will work together to reach maximal precision.
If some input has 0/+40dB preamplifier with 10dB step and -10/+10dB mixer
with 1dB step after it, new code will use both to provide 0/+40dB control
with 1dB step! We could even get -10/+50dB range there, but that is
intentionally blocked for now.
- different channels of multichannel associations on non-uniform CODECs
such as VIA VT1708S will have the same volume, not looking that control
ranges are different. It was not good when fronts were 12dB louder.
- for multiplexed recording, when we can record from only one source at
a time, we can now use recording amplifier controls to set different
volume levels for different inputs if they have no own controls of they
are less precise. If recording source change, amplifiers will be
reconfigured.
To improve out-of-the-box behavior, ignore default volume levels set by
sound(4) and use own, more reasonable: +20dB for mics, -10dB for analog
output volume and 0dB for the rest of controls. sound(4) defaults of 75%
mean absolutely random things for different controls of different CODECs
because of very different control ranges.
Together with further planned automatic recording source selection this
should allow users to get fine playback and recording without touching
mixer first.
Note that existing users should delete /var/db/mixer*-state and reboot
or trigger CODEC reconfiguration to get new default values.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
versions derived from /usr/ports/audio/oss.
The particular headers used were taken from the
attic/drv/oss_allegro directory and are mostly identical
to the previous files.
The Maestro3 driver is now free from the GPL.
NOTE: due to lack of testers this driver is being
considered for deprecation and removal.
PR: kern/153920
Approved by: jhb (mentor)
MFC after: 2 weeks
