Always use sys/conf/kern.mk when building kernel/modules.
<bsd.kern.mk> is only preserved for sys/boot/pc98/boot2
for now, but this will be fixed. If there are other
users of <bsd.kern.mk>, please let me know.
Reminded by: bde
Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Move <sys/conf.h> before <sys/disk.h>.
No need for raidread()/raidwrite(), we have generic code for that.
Remove non-functional dump code.
Make raidinit() return the softc, not the dev_t.
Move to "struct disk*" centric API.
Fix printfs' to get name from struct disk instead of dev_t.
OK'ed by: scottl
don't end up freezing the box. This makes VTY locking useless
in the DDB case but a box which is supposed to be physically
secure shouldn't compile DDB anyway.
Reviewed by: silence on -audit
To do this, initialize the d_maj member of the cdevsw to MAJOR_AUTO.
When the cdevsw is first passed to make_dev() a free major number
will be assigned.
Until we have a bit more experience with this a printf will announce
this fact.
Major numbers are not reclaimed, so loading/unloading the same
device driver which uses MAJOR_AUTO will eventually deplete the
pool of free major numbers and the system will panic when it can
not allocate one. Still undecided who to invonvenience with the
solution to this.
Improve SBP device probeing:
- Wait 2 sec before issuing LOGIN ORB expecting the reconnection
hold timer expires.
- Serialize management ORB and scanning LUN by CAM on each target.
This should fix the problem for devices which have multiple LUNs.
Test device is donated by: Jaye Mathisen <mrcpu@internetcds.com>
- Freeze SIM queue for 2 sec after BUS RESET.
- Retry with LOGIN rather than RECONNECT after LOGIN is not completed for
BUS RESET.
- Use appropriate CAM status for BUS RESET and DEVICE RESET.
- Let CAM to scan targets after BUS REST.
- Implement CAM scan target function.
- Keep our own devq freeze count.
- Let CAM to know that SBP does tagged queuing.
These should be merged to RELENG_4 before 4.8-RELEASE.
