would sometimes result in a corrupted file was reported via email.
This problem appears to have been caused by r251719 (reverting
r251719 fixed the problem). Although I have not been able to
reproduce this problem, I suspect it is caused by another thread
increasing np->n_size after the mtx_unlock(&np->n_mtx) but before
the vnode_pager_setsize() call. Since the np->n_mtx mutex serializes
updates to np->n_size, doing the vnode_pager_setsize() with the
mutex locked appears to avoid the problem.
Unfortunately, vnode_pager_setsize() where the new size is smaller,
cannot be called with a mutex held.
This patch returns the semantics to be close to pre-r251719 (actually
pre-r248567, r248581, r248567 for the new client) such that the call to
vnode_pager_setsize() is only delayed until after the mutex is
unlocked when np->n_size is shrinking. Since the file is growing
when being written, I believe this will fix the corruption.
A better solution might be to replace the mutex with a sleep lock,
but that is a non-trivial conversion, so this fix is hoped to be
sufficient in the meantime.
Reported by: David G. Lawrence (dg@dglawrence.com)
Tested by: David G. Lawrence (to be done soon)
Reviewed by: kib
MFC after: 1 week
is initialized with !ND6_IFF_AUTO_LINKLOCAL && !ND6_IFF_ACCEPT_RTADV
regardless of net.inet6.ip6.accept_rtadv and net.inet6.ip6.auto_linklocal.
To configure an autoconfigured link-local address (RFC 4862), the
following rc.conf(5) configuration can be used:
ifconfig_bridge0_ipv6="inet6 auto_linklocal"
- if_bridge(4) now removes IPv6 addresses on a member interface to be
added when the parent interface or one of the existing member
interfaces has an IPv6 address. if_bridge(4) merges each link-local
scope zone which the member interfaces form respectively, so it causes
address scope violation. Removal of the IPv6 addresses prevents it.
- if_lagg(4) now removes IPv6 addresses on a member interfaces
unconditionally.
- Set reasonable flags to non-IPv6-capable interfaces. [*]
Submitted by: rpaulo [*]
MFC after: 1 week
system has svnliteversion.
- If svnliteversion is not found, look for svnversion in /usr/bin
and /usr/local/bin, since svnlite can be installed as svn if
WITH_SVN is set.[1]
- Remove /bin from binary search paths.[1]
Discussed with: kib [1]
MFC after: 3 days
Approved by: kib (mentor)
algorithm, which is based on the 2011 v0.1 patch release and described in the
paper "Revisiting TCP Congestion Control using Delay Gradients" by David Hayes
and Grenville Armitage. It is implemented as a kernel module compatible with the
modular congestion control framework.
CDG is a hybrid congestion control algorithm which reacts to both packet loss
and inferred queuing delay. It attempts to operate as a delay-based algorithm
where possible, but utilises heuristics to detect loss-based TCP cross traffic
and will compete effectively as required. CDG is therefore incrementally
deployable and suitable for use on shared networks.
In collaboration with: David Hayes <david.hayes at ieee.org> and
Grenville Armitage <garmitage at swin edu au>
MFC after: 4 days
Sponsored by: Cisco University Research Program and FreeBSD Foundation
If n fds were passed, it would receive the first one n times.
Reported by: Shawn Webb <lattera@gmail.com>, koobs, gleb
Tested by: koobs, gleb
Reviewed by: pjd
in gpart(8) and boot(8), adding references to gptboot(8) in both.
Reviewed by: jhb, ae, pjd, Paul Schenkeveld <bsdcan@psconsult.nl>, david_a_bright@dell.com (portions), gjb
MFC after: 1 week
Revert the simplification of the i_gen calculation.
It is still a good idea to avoid zero values and for the case
of old filesystems there is probably no advantage in using
the complete 32 bits anyways.
Discussed with: bde
MFC after: 4 weeks
will crash when doing a large write, since m_get2() would
return NULL. This patch fixes the problem, since nfsm_uiotombuf()
will allocate additional mbufs, as required.
Reported by: sbruno
Tested by: sbruno
Discussed with: glebius
While this prevents commands getting stuck forever there is no way to guarantee
that data from the command hasn't been committed to the device.
In addition older mfi firmware has a bug that would cause the controller to
frequently stall IO for over our timeout value, which when combined with
a forced timeout often resulted in panics in UFS; which would otherwise be
avoided when the command eventually completed if left alone.
For reference this timeout issue is resolved in Dell FW package 21.2.1-0000.
Fixed FW package version for none Dell controller will likely vary.
MFC after: 2 days
Further simplify the i_gen calculation for older disks.
Having a zero here is not really a problem and this is more
similar to what is done in newfs_random().
Reported by: Xin Li
MFC after: 4 weeks
defined by <sys/dirent.h>
Always start parsing at DIRBLKSIZ aligned offset, skip first entries if
uio_offset is not DIRBLKSIZ aligned. Return EINVAL if buffer is too
small for single entry.
Preallocate buffer for cookies. Cookies will be replaced with d_off
field in struct dirent at later point.
Skip entries with zero inode number.
Stop mangling dirent in ufs_extattr_iterate_directory().
Reviewed by: kib
Sponsored by: Google Summer Of Code 2011
In UFS, i_gen is a random generated value and there is not way for
it to be negative. Actually, the value of i_gen is just used to
match bit patterns and it is of not consequence if the values are
signed or not.
Following other filesystems, set it to unsigned and use it as such,
Discussed by: mckusick
Reviewed by: mckusick (previous version)
MFC after: 4 weeks
Issues were noted by Bruce Evans and are present on all architectures.
On i386, a counter fetch should use atomic read of 64bit value,
otherwise carry from the increment on other CPU could be lost for the
given fetch, making error of 2^32. If 64bit read (cmpxchg8b) is not
available on the machine, it cannot be SMP and it is enough to disable
preemption around read to avoid the split read.
On x86 the counter increment is not atomic on purpose, which makes it
possible for the store of the incremented result to override just
zeroed per-cpu slot. The effect would be a counter going off by
arbitrary value after zeroing. Perform the counter zeroing on the
same processor which does the increments, making the operations
mutually exclusive. On i386, same as for the fetching, if the
cmpxchg8b is not available, machine is not SMP and we disable
preemption for zeroing.
PowerPC64 is treated the same as amd64.
For other architectures, the changes made to allow the compilation to
succeed, without fixing the issues with zeroing or fetching. It
should be possible to handle them by using the 64bit loads and stores
atomic WRT preemption (assuming the architectures also converted from
using critical sections to proper asm). If architecture does not
provide the facility, using global (spin) mutex would be non-optimal
but working solution.
Noted by: bde
Sponsored by: The FreeBSD Foundation
instead of allocating new one each time
All limits are set to RLIM_INFINITY which sould be ok (even though we
care only about RLIMT_FSIZE in this case).
MFC after: 1 week
According to the standard, atomic_fetch_*() has to behave identical to
regular arithmetic. This means that for pointer types, we have to apply
the stride when doing addition/subtraction.
The GCC documentation seems to imply this is done for __sync_*() as
well. Unfortunately, both tests and Googling seems to reveal this is not
really the case. Fix this by performing the multiplication with the
stride manually.
- According to the standard, memory_order is a type. Use a typedef.
- atomic_*_fence() and atomic_flag_*() are described by the standard as
functions. Use inline functions to implement them.
- Only expose the atomic_*_explicit() functions in kernel space. We
should not use the short-hand functions, as they will always use
memory_order_seq_cst.
state. Previously it used to check if controller has sent a
PAUSE frame to the remote peer.
Reported by: David Imhoff via Brad Smith <brad@OpenBSD.org>
Submitted by: davidch (initial version)
Reviewed by: davidch, David Imhoff <dimhoff_devel@xs4all.nl>
