Xcpustop(). %es is used in at least the call to savectx() when savectx()
calls bcopy(), so not loading it was fatal if a stop IPI interrupts
user mode.
This reduces bugs starting and stopping CPUs for debuggers. CPUs are
stopped mainly in kdb_trap() and cpu_reset(). At reset time there is
a good chance that all the CPUs are in the kernel, so the bug was
probably harmless then.
This is just a cleanup here (modulo rev.1.108 of kern/tty.c), since the
input speed can be different from to output speed and extra code to
handle both speeds naturally handled all cases.
cd_setreg() were still using !(read_eflags() & PSL_I) as the condition
for the lock hidden by COM_LOCK() (if any) being held. This worked
when spin mutexes and/or critical_enter() used hard interrupt disablement,
but it has caused recursion on the non-recursive mutex com_mtx since
all relevant interrupt disablement became soft. The recursion is
harmless unless there are other bugs, but it breaks an invariant so
it is fatal if spinlocks are witnessed.
be gone in FreeBSD 6, so put BURN_BRIDGES around it. The TRB also
felt that if something better comes along sooner, it can be used to
replace this code.
Delayed by: BSDcon and subsequent disk crash.
Quick fix for calling DELAY() for ddb input in some (atkbd-based)
console drivers. ddb must not use any normal locks, but DELAY()
normally calls getit() which needs clock_lock. One problem with using
normal locks in ddb is that deadlock is possible, but deadlock on
clock_lock is unlikely becaluse clock_lock is bogusly recursive,
apparently just to hide the problem of ddb using it. The i8254 clock
hardware has mostly write-only registers so it is important for it to
use a lock that gives exclusive access. (atkbd hardware is also
unfriendly to reentrant software but that problem is more local and
already solved.) I mostly saw the symptoms of the bug caused by
unlocking in getit() running cpu_unpend(). cpu_unpend() should not
be called while in ddb and Debugger() calls for failing assertions
about this caused a breakpoint within ddb.
ddb must also not call getit() because ddb may be being used to step
through clock initialization code that has stopped or otherwise mangled
the clock. If the clock is stopped, then getit() always returns the
same value and DELAY() takes forever if it trusts getit().
The quick fix is implement DELAY(n) as (n * timer_freq / 1000000)
inb(0x84)'s if ddb is active.
machdep.c:
Don't permit recursion on clock_lock.
A timecounter will be selected when registered if its quality is
not negative and no less than the current timecounters.
Add a sysctl to report all available timecounters and their qualities.
Give the dummy timecounter a solid negative quality of minus a million.
Give the i8254 zero and the ACPI 1000.
The TSC gets 800, unless APM or SMP forces it negative.
Other timecounters default to zero quality and thereby retain current
selection behaviour.
ioctls.
In the particular case of ptrace(), this commit more-or-less reverts
revision 1.53 of sys_process.c, which appears to have been erroneous.
Reviewed by: iedowse, jhb
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
in the `video_state' structure, to larger ones (from u_char to
u_short). Each can now hold values at least as large as the
size of the array it is meant to point into.
This eliminates warnings printed by GCC 3.3.1 and hence makes
pcvt compilable using -Werror.
work when using a graphics chipset which identifies itself as
`VIA CLE266', used in some VIA EPIA boards. Two values need to be
patched in the VESA mode information structure: the widths of the modes
mentioned above are encoded in a format which was unknown to the VESA
module (and to my copy of the VBE spec.) whereas the window memory
segment values seem to be just incorrect.
I tested this on a VIA EPIA-M9000 and -M10000.
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
lot of work to make this driver work under current. In the past when
people wanted to remove xten, I was the only one in the way. After
talking to fsmp@ (last person to make real changes to this driver)
about this, I'm convinced it is better left in the dust-bin of history
Approved by: re@ (scottl)
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
