an override as a loader settable variable (fxp_iomap). fxp_iomap is
a bitmap of fxp units that should be configured to use PCI I/O space
in stead of PCI Memory space.
Reviewed by: Kees Jan Koster <dutchman@tccn.cs.kun.nl>, dg@freebsd.org
we must also inform the card of this change. Otherwise the sequencer
will traverse a corrupt list of SCBS. The side effects of this problem
were unknown SCBs completing in the qoutfifo or worse yet, panics due
to sequencer interrupts that referenced what, to the kernel, were invalid
SCB ids.
- Use proper atomic operations to make the run time initialization
controlled by svr_str_initialized be MP safe.
- Use appropriate queue(3) macros where needed.
Initialize rid to 0. This doesn't seem to make any difference
(the driver doesn't care what rid it gets and no-one seems to
check rid's value), but follows standard conventions.
Pass in our device_t to ahc_alloc(). We now use device_T
softc storage, so passing NULL results in a panic.
Set the unit number in our softc so that the driver core
can retrieve it.
ahc_pci.c:
Set the unit number in our softc so that the driver core
can retrieve it.
aic7770.c:
Insert our softc into the list of softcs when initialization
is successful.
aic7xxx.c:
Remove a workaround for an aic7895 bug we will never trigger.
Add additional diagnostic info to ahc_dump_card_state().
Always panic the system if a sequencer assertion fails.
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
Replace a hard coded number with a constant.
Guard against looping forever in ahc_pause_and_flushwork().
A hot eject or card failure may make the intstat register
return 0xFF, so limit the number of interrupts we'll process.
Correct the code in ahc_search_qinfifo() that guarantees that
the sequencer will see an abort collision if the qinfifo is
modified when a DMA is in progress. We now do this fixup
after modifying the queue. This guarantees that the HSCB
we place at the head of the queue is not the same as the
old head. Using "next hscb" (guaranteed not to be the
same as the first SCB) before clearing the queue could free
up the original head hscb to be used during a remove operation
placing it again at the head of the qinfifo.
aic7xxx.h:
Reduce the maximum number of outstanding commands to 253 from
254. To handle our output queue correctly on machines that only
support 32bit stores, we must clear the array 4 bytes at a
time. To avoid colliding with a DMA write from the sequencer,
we must be sure that 4 slots are empty when we write to clear
the queue. This reduces us to 253 SCBs: 1 that just completed
and the known three additional empty slots in the queue that
preceed it. Yahoo was able to force this race on one of their
systems. Interrupts were disabled for such a time that the
entire output queue was filled (254 entries complete without
any processing), and our 32bit write to clear the status clobbered
one entry.
Add a feature tag for devices that are removable.
aic7xxx.reg:
Never use the sequencer interrupt value of 0xF0. We need
to guanrantee that an INTSTAT value of 0xFF can only occur
during card failure or a hot-eject.
Align the busy targets table with the begining of scratch
space. This seems to appease a chip bug in the aic7895.
aic7xxx.seq:
Be sure to disable select-out after a bus free event that occurs
early in a selection. If we don't disable select-out, we will
believe that it is enabled even though a new selection will never
occur.
Move the clearing of SELDI to just before a jump. This appeases
another chip bug of the aic7895.
Make the target mode command loop a bit more efficient.
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
Properly cleanup the last SCB we tested against should we
fail to properly find an SCB for a reselection.
Add some additional sequencer debugging code.
aic7xxx_freebsd.c:
Limit the driver to 253 outstanding commands per adapter.
Guard against overflow in timeout handling.
aic7xxx_inline.h:
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
aic7xxx_pci.c:
Set the removable feature for the apa1480 cardbus and the 29160C
Compact PCI card.
Don't report high byte termination information for narrow cards.
Use a PCI read rather than a questionable delay when fetching/setting
termination settings.
MFC'ed i due time. I can't test it under current right now because
netgraph seems to do unethical things with mutexes.
musycc:
Add status per channel.
Reduce printf chattyness
Keep error counters line if_mn does.
Increase descriptor count.
if_mn:
Support experimental unframed E1 lines.
These two drivers should share more code relating to framed channelized
TDM media in general (T1/E1/E3/T3, Sonet). Anyone interested email me.
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
parts: isa and pccard. The isa one is known to work with an IBM
EtherJet ISA card. The pccard one isn't known to work because the
EtherJet pccard I purchased recently arrived DOA :-(. I'll commit the
pccard.conf entry when the replacement card arrives.
I plan on MFC this in a week or two.
o 1.111 imp Sync with FreeBSD.
o 1.110 nonaka Add Roland SCP-55
o 1.109 ichiro add NANOSPEED ROOT-RZ2000 WLAN Card
o 1.108 ichiro add EMTAC A2424i 11Mbps WLAN Card
o 1.107 haya Add IO Data CBIDE2 ata interface card.
o 1.106 jhawk s/NULL}/NULL }/
o 1.105 thorpej " " -> "&sp" in two entries, per Rafal Boni.
o 1.104 thorpej Add SMC 2632W. From Rafal Boni, kern/11775.
o 1.103 drochner add IBM microdrive
o 1.102 soren Typo.
o 1.101 hubertf Add ELSA WaveLAN card & a noname clone(?)
o 1.100 toddpw Socket Comm. PC Card Ethernet, and tidy up naming.
o 1.99 msaitoh MELCO LPC2-TX, Telecom Device TCD-HPC100,
MACNICA ME1-JEIDA
o 1.98 imp Sort BAY into numerical order. (already in FreeBSD)
if_vr: handle the case where vr_encap() returns failure: bust out of the
packet sending loop instead of panicking. Also add some missing
newlines to some printf()s.
if_dc: The miibus_read and miibus_write methods keep swapping in and
out of MII mode by fiddling with CSR6 for cards with MII PHYs.
This is a hack to support the original Macronix 98713 card which
has built-in NWAY that uses an MII-like management interface
even though it uses serial transceivers. Conditionalize this
so that we only do this on 98713 chips, since it does bad things
to genuine tulip chips (and maybe other clones).
