or stg driver. They are,
Macnica mPS110, PANASONIC(KME) KXLC004, Qlogic Fast SCSI,
Workbit Ultra Ninja-16, (ID based)
Future Domain SCSI2GO, IBM SCSI PCMCIA card, I-O DATA CBSC16,
Macnica mPS100, Newmedia BASICS-SCSI, RATOC REX-5536, RATOC REX-5536AM,
RATOC REX-5536M, RATOC REX5572, Workbit NinjaSCSI-3
(CIS based)
Note: We need vendor IDs WORKBIT2 and IODATA3 which is -1, since some
cards does not have IDs in the CIS and fails to be probed without
this fake vendor IDs.
o Change the strings of RATOC REX_R280 from REX-R280 to REX-R280/REX-9530.
This reminds us that REX-R280 and REX-R9530 have same ID (same product).
Reviewed by: imp
Approved by: re
Obtained from: /etc/defaults/pccard.conf,
List of CIS tupples by Toshihiko ARAI and PAO project:
http://www.linkclub.or.jp/~clover/cis/
Change suggestion by: HASEGAWA Tomoki <thasegawa@mta.biglobe.ne.jp>
for I-O DATA CBSC16 entry
There were no serious problem reports on this in spite of my concern.
To get debug output from acpi_pci_link, just enable bootverbose flag
in usual manner (boot -v).
Approved by: re
aicasm_gram.y:
Use a direct move from allzeros to emulate a
mvi of 0.
aicasm_insformat.h:
sync $Id$
aicasm_symbol.c:
Minor header change.
Approved by: re (blanket)
pci_get_ether accesor, which gets it from the CIS for cardbus cards
(and from other pci-like buses via whatever mechanism is used there).
Submitted by: sam
Approved by: re (blanket)
sometimes, so return it when requested and it does. Also a little
more infrastructure for a few other things.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
buses support querying the MAC address in a standard-for-that-bus way.
The base pci bus returns NULL for this IVAR always.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
- If a PCI device is not present, then a 32-bit read_config() is going to
return 0xffffffff not 0xffff.
- For the 82454NX chipset, the MIOC that we read the bus numbers of the
various host-PCI bridges from is at function (slot) 0x10 not 0x0.
Approved by: re (rwatson)
1. Detect the revision of the Rhine chip we're using.
2. Use the force reset command on revisions which support
it whenever the normal reset command fails.
This should solve a wide range of "my vr0 locks up with reset
failed messages" problems. (Although the root causes should
be eventually tracked down.)
Tested by: grenville armitage <garmitage@swin.edu.au>
Obtained from: Via's if_fet driver
MFC after: 3 days
Approved by: re
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
to PCI bridge can be read be evaluating the _BBN method of the host to PCI
device. Unfortunately, there appear to be some lazy/ignorant/moronic/
whatever BIOS writers that return 0 for _BBN for all host to PCI bridges in
the system. On a system with a single host to PCI bridge this is not a
problem as the child bus of that single bridge will be bus 0 anyway.
However, on systems with multiple host to PCI bridges and l/i/m/w BIOS
writers this is a major problem resulting in all but the first host to
PCI bridge failing to attach. So, this adds a workaround.
If the _BBN of a host to PCI bridge is zero and pcib0 already exists
and is not us, the we use _ADR to look up our PCI function and slot
(we currently assume we are on bus 0) and use that to call
host_pcib_get_busno() to try and extract our bus number from config
registers on the host to PCI bridge device. If that fails, then we make
an evil assumption that ACPI's _SB_ namespace lays out the host to PCI
bridges in ascending order and use our pcib unit number as our bus
number.
Approved by: re
after configure() has run. Only create the device if ofwcons is the
highest priority console. Make a dev alias with the same name as the
firmware output-device property.
trigger a breakpoint with this chip.
- Fiddle the right bits in the cn input and output routines to disable port
interrupts and enable visibility of the masked interrupt status bits.
- Register a shutdown final event handler to put the chip back in the mode
that the prom expects.
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
o Use 32-bit unsigned types for things that really are 32-bit quantities,
not bus_addr_t. These are not the same as a bus_addr_t, so don't use
that here. Harmless on i386, introduced problems on sparc64.
Submitted by: jhb
