The old version had a race between the time that the old file was
cp'ed to acct.0 and the time that 'sa -s' was run that prevented
the commands that occurred in the meantime from being backed up.
It's also arguable that the old version was inefficient in using
cp which can be a problem on a space-constrained system.
This version avoids both problems, albeit it's considerably more
complicated. The advantage of putting the log rotation in the rc.d
script is that it can handle the _enable and _file questions without
having to do gymnastics to discover either value in the periodic script.
As a side effect of reviewing the rc.d script I cleaned it up a bit.
A full featured groff is required during buildworld, so build it always
and don't rely on it being present on the host system.
vgrind(1) is tightly coupled to a roff processor and will not be
built/installed when groff is disabled. Also much of the roff'ed
documentation under share/doc will not be built/installed when
WITHOUT_GROFF is defined.
Reviewed by: ru (partial)
pc-sysinstall) a replacement for sysinstall in the 9.0 release and beyond.
Currently supported platforms are sparc64, pc98, i386, amd64, powerpc, and
powerpc64. Integration into the build system will occur in the coming
weeks.
Merging with pc-sysinstall will use this code as a frontend, while
temporarily retaining the interactive partition editor here. This work
will be done in parallel with improvements on this code and release
integration.
Thanks to all who have provided testing and comments!
zpool the output causes the script to bail out with syntax errors.
Since a scrub of a faulted zpool is pointless, just skip over any pools
marked as such.
PR: conf/150228
Submitted by: jpaetzel
Approved by: kib (mentor)
MFC after: 3 days
MFC note: only for RELENG_8
While I'm here, don't run the sysctl frob unconditionally, and
s/sysctl/$SYSCTL/
PR: conf/153460 [1]
Submitted by: Grigory Rechistov <ggg_mail@inbox.ru>
and configure minimal target addresses & notifications needed for bsnmpd(1)
to send SNMPv3 notifications.
Sponsored by: The FreeBSD Foundation
Reviewed by: philip
Approved by: philip
snmp_vacm modules and minimal user/view configurations needed to for
the modules to work properly.
Sponsored by: The FreeBSD Foundation
Reviewed by: philip@ (mostly)
Approved by: philip@
case user wants to implement his own actions and doesn't want the attributes to
vanish.
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 3 days
and add protocol entries for protocols which have SCTP port allocations.
These entries are according to
http://www.iana.org/assignments/port-numbers
as of today. Also add SCTP port allocation entires for the
echo, daytime, and chargen service.
Discussed with rwatson@
MFC after: 3 days.
group on a object has less permissions that everyone). These
permissions will not work reliably over NFS if you have more than
14 supplemental groups and are usually not what you mean.
MFC after: 1 week
Hardware donated by: Rusty Nejdl rnejdl at ringofsaturn dot com
Tested by: Rusty Nejdl rnejdl at ringofsaturn dot com
Tested by: Andrzej Tobola ato at iem dot pw dot edu dot pl
MFC after: 3 weeks
set to use DHCP have no carrier. This can cause grief as it may take
some time for link to be established, and defaultroute may terminate
before this happens.
Introduce a defaultroute_carrier_delay variable and then wait that long
in defaultroute before bailing if no interfaces have carrier. With the
default settings defaultroute will wait for five seconds for this, and
the original 30 second wait for a default route to appear is unchanged.
Note that there is in discussion an alternative approach to the broader
problem of waiting for DHCP-configured routes. However, this change
addresses a real problem in the current defaultroute script.
Discussed on: freebsd-rc@
- looking for partition with 'bootonce' attribute alone (without 'bootme'
attribute), removing it and logging that we successfully booted from this
partition.
- looking for partitions with 'bootfailed' attribute, removing it and
logging that we failed to boot from this partition.
Reviewed by: arch (Message-ID: <20100917234542.GE1902@garage.freebsd.pl>)
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 2 weeks
The $ip6addrctl_policy is a variable to choose a pre-defined address
selection policy set by ip6addrctl(8).
The keyword "ipv4_prefer" sets IPv4-preferred one described in Section 10.3,
the keyword "ipv6_prefer" sets IPv6-preferred one in Section 2.1 in RFC 3484,
respectively. When "AUTO" is specified, it attempts to read
/etc/ip6addrctl.conf first. If it is found, it reads and installs it as
a policy table. If not, either of the two pre-defined policy tables is
chosen automatically according to $ipv6_activate_all_interfaces.
When $ipv6_activate_all_interfaces=NO, interfaces which have no corresponding
$ifconfig_IF_ipv6 is marked as IFDISABLED for security reason.
The default values are ip6addrctl_policy=AUTO and
ipv6_activate_all_interfaces=NO.
Discussed with: ume and bz
