- Add a retry loop for the i2c sensor reading.
- Check on busy status of the chip and on invalid values.
- Fix a typo in a comment.
- Replace the constant 2732 with the ZERO_C_TO_K macro.
Approved by: nwhitehorn (mentor)
signalled when the attribute address for the CF is 0 in the octeon
sysinfo structure. In this mode, the DATA port is 16-bits, but the
other ports are 8-bits, but on a 16-bit bus (so you have to access it
a short at a time, but only believe the lower byte). See the code for
more details on this slightly odd arrangement. I'm still not 100%
happy with the abstractions here on many levels (starting with the
globals for these settings, on down to no bus_space use, etc), but the
driver had these problems before the change.
Also, clean up the code a bit to make this support easier, and the
code a bit easier to read. I tried to follow existing style, but may
have missed a few spots. Add some comments.
Fix probe/attach routine to return a proper error for the simulator.
With this change, my EBH5200 eval board now recognizes the CF well
enough to boot to the login prompt. Before it would say it never
became ready. My CN3010-EVB-HS5 still boots properly. My older
CN3860-based board won't load the 64-bit kernel, either before or
after the change, and I didn't chase that down.
module.
* If sc->sc_dodfs is set to 1 by the ath_dfs_radar_enable(),
set the relevant rx filter bit to begin receiving radar PHY
errors. The HAL code already knows how to set the relevant
error mask register to enable radar events.
* Add a missing call to ath_dfs_radar_enable() after ath_hal_reset()
* change ath_dfs_process_phyerr() to take a const char *buf for now,
rather than a descriptor. This way it can get access to the packet
buffer contents.
pmap_sync_icache() to sync random (possibly uncached or nonexisting!)
memory, causing kernel page faults or machine checks, most easily
triggered by using GDB. While here, add an additional safeguard to only
sync cacheable memory.
MFC after: 2 days
doesn't return an error when the underlying file system
lacks support for any of the four _PC_xxx values used, by
falling back to default values.
Tested by: avg
MFC after: 2 weeks
real owner of the device ID. Also rename the associated config
function while here.
- Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152
and Exar XR17C154.
Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl
MFC after: 1 week
- Add a retry loop for the i2c sensor reading.
- Update the sensor handling for sensors which do not have a location
entry. [1]
Submitted by: [1] Justin Hibbits.
Approved by: nwhitehorn (mentor)
They are media-dependent and may change in run-time, same as sectorsize
and/or mediasize.
SCSI devices return physical sector size and offset via READ CAPACITY(16)
command and so can not report it until media inserted or at least until
probe sequence completed. UNMAP support is also reported there.
due to m_uiotombuf() failing.
While here, trim unneeded error handling related to tuninit() since it
can never fail.
Submitted by: Martin Birgmeier la5lbtyi aon at
Reviewed by: glebius
MFC after: 1 week
(up to 2048 instead of 256 or even 64) of them with single TRIM request.
OCZ Vertex2/Vertex3 SSDs can handle no more then 64 ranges per TRIM request.
Due to lack of BIO_DELETE clustering now, it means that we could delete no
more then 2MB per request (on FS with 32K block) with limited request rate.
This change increases delete rate on Vertex2 from 250MB/s to 950MB/s.
Renovate and improve the AIM Open Firmware support:
- Add RTAS (Run-Time Abstraction Services) support, found on all IBM systems
and some Apple ones
- Improve support for 32-bit real mode Open Firmware systems
- Pull some more OF bits over from the AIM directory
- Fix memory detection on IBM LPARs and systems with more than one /memory
node (by andreast@)
These cause problems when trying to include the header in a C++ project.
Rename them to 'evt_class', and track the change in mfi and mfiutil.
Submitted by: Mark Johnston
Sponsored by: Sandvine Incorporated
Reviewed by: jhb@
MFC after: 1 week
crusty, and this still isn't perfect, but its at least a bit
more recent.
Secondly, a few improvements to the driver from Andrew Boyer,
support hint to allow devices to not attach, add VLAN_HWTSO
capability so vlans can use TSO, fix in the interrupt handler
to make sure the stack TX queue is processed. Oh, and also
make sure IPv6 does not cause a re-init in the ioctl routine.
Thanks for your efforts Andrew!
Thanks to Claudio Jeker for noticing the ixgbe_xmit() routine
was not correctly swapping the dma map from the first to the
last descriptor in a multi-descriptor transmission, corrected
this.
VM_PAGER_AGAIN to VM_PAGER_ERROR for the uwritten pages. Return
VM_PAGER_AGAIN for the partially written page. Always forward at least
one page in the loop of vm_object_page_clean().
VM_PAGER_ERROR causes the page reactivation and does not clear the
page dirty state, so the write is not lost.
The change fixes an infinite loop in vm_object_page_clean() when the
filesystem returns permanent errors for some page writes.
Reported and tested by: gavin
Reviewed by: alc, rmacklem
MFC after: 1 week
This is in no way a complete DFS/radar detection implementation!
It merely creates an abstracted interface which allows for future
development of the DFS radar detection code.
Note: Net80211 already handles the bulk of the DFS machinery,
all we need to do here is figure out that a radar event has occured
and inform it as such. It then drives the DFS state engine for us.
The "null" DFS radar detection module is included by default;
it doesn't require a device line.
This commit:
* Adds a simple abstracted layer for radar detection state -
sys/dev/ath/ath_dfs/;
* Implements a null DFS module which doesn't do anything;
(ie, implements the exact behaviour at the moment);
* Adds hooks to the ath driver to process received radar events
and gives the DFS module a chance to determine whether
a radar has been detected.
Obtained from: Atheros
Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.
The particulars:
* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.
The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.
Obtained from: Linux, Atheros
default dispatch method to NETISR_DISPATCH_DIRECT in order to force
direct dispatch. This adds a fairly negligble overhead without
changing default behavior, but in the future will allow deferred or
hybrid dispatch to other worker threads before link layer processing
has taken place.
For example, this could allow redistribution using RSS hashes
without ethernet header cache line hits, if the NIC was unable to
adequately implement load balancing to too small a number of input
queues -- perhaps due to hard queueset counts of 1, 3, or 8, but in
a modern system with 16-128 threads. This can happen on highly
threaded systems, where you want want an ithread per core,
redistributing work to other queues, but also on virtualised systems
where hardware hashing is (or is not) available, but only a single
queue has been directed to one VCPU on a VM.
Note: this adds a previously non-present assertion about the
equivalence of the ifnet from which the packet is received, and the
ifnet stamped in the mbuf header. I believe this assertion to
generally be true, but we'll find out soon -- if it's not, we might
have to add additional overhead in some cases to add an m_tag with
the originating ifnet pointer stored in it.
Reviewed by: bz
MFC after: 3 weeks
Sponsored by: Juniper Networks, Inc.
dynamic rules. We are doing forwarding in the following cases:
o For the simple ipfw fwd rule, e.g.
fwd 10.0.0.1 ip from any to any out xmit em0
fwd 127.0.0.1,3128 tcp from any to any 80 in recv em1
o For the dynamic fwd rule, e.g.
fwd 192.168.0.1 tcp from any to 10.0.0.3 3333 setup keep-state
When this rule triggers it creates a dynamic rule, but this
dynamic rule should forward packets only in forward direction.
o And the last case that does not work before - simple fwd rule which
triggers when some dynamic rule is already executed.
PR: kern/147720, kern/150798
MFC after: 1 month
In msgbuf_reinit() and msgbuf_init(), we weren't initializing the mutex.
Depending on the contents of memory, the LO_INITIALIZED flag might be
set on the mutex (either due to a warm reboot, and the message buffer
remaining in place, or due to garbage in memory) and in that case, with
INVARIANTS turned on, we would trigger an assertion that the mutex had
already been initialized.
Fix this by bzeroing the message buffer mutex for the _init() and _reinit()
paths.
Reported by: mdf
