zfs_getattr_fast() was missing a lock on the ZFS superblock which
could result in zfs_znode_dmu_fini() clearing the zp->z_sa_hdl member
while zfs_getattr_fast() was accessing the znode. The result of this
would usually be a panic.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes#431
While the existing implementation of .writepage()/zpl_putpage() was
functional it was not entirely correct. In particular, it would move
dirty pages in to a clean state simply after copying them in to the
ARC cache. This would result in the pages being lost if the system
were to crash enough though the Linux VFS believed them to be safe on
stable storage.
Since at the moment virtually all I/O, except mmap(2), bypasses the
page cache this isn't as bad as it sounds. However, as hopefully
start using the page cache more getting this right becomes more
important so it's good to improve this now.
This patch takes a big step in that direction by updating the code
to correctly move dirty pages through a writeback phase before they
are marked clean. When a dirty page is copied in to the ARC it will
now be set in writeback and a completion callback is registered with
the transaction. The page will stay in writeback until the dmu runs
the completion callback indicating the page is on stable storage.
At this point the page can be safely marked clean.
This process is normally entirely asynchronous and will be repeated
for every dirty page. This may initially sound inefficient but most
of these pages will end up in a few txgs. That means when they are
eventually written to disk they should be nicely batched. However,
there is room for improvement. It may still be desirable to batch
up the pages in to larger writes for the dmu. This would reduce
the number of callbacks and small 4k buffer required by the ARC.
Finally, if the caller requires that the I/O be done synchronously
by setting WB_SYNC_ALL or if ZFS_SYNC_ALWAYS is set. Then the I/O
will trigger a zil_commit() to flush the data to stable storage.
At which point the registered callbacks will be run leaving the
date safe of disk and marked clean before returning from .writepage.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When modifing overlapping regions of a file using mmap(2) and
write(2)/read(2) it is possible to deadlock due to a lock inversion.
The zfs_write() and zfs_read() hooks first take the zfs range lock
and then lock the individual pages. Conversely, when using mmap'ed
I/O the zpl_writepage() hook is called with the individual page
locks already taken and then zfs_putpage() takes the zfs range lock.
The most straight forward fix is to simply not take the zfs range
lock in the mmap(2) case. The individual pages will still be locked
thus serializing access. Updating the same region of a file with
write(2) and mmap(2) has always been a dodgy thing to do. This change
at a minimum ensures we don't deadlock and is consistent with the
existing Linux semantics enforced by the VFS.
This isn't an issue under Solaris because the only range locking
performed will be with the zfs range locks. It's up to each filesystem
to perform its own file locking. Under Linux the VFS provides many
of these services.
It may be possible/desirable at a latter date to entirely dump the
existing zfs range locking and rely on the Linux VFS page locks.
However, for now its safest to perform both layers of locking until
zfs is more tightly integrated with the page cache.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #302
There is at most a factor of 3x performance improvement to be
had by using the Linux generic_fillattr() helper. However, to
use it safely we need to ensure the values in a cached inode
are kept rigerously up to date. Unfortunately, this isn't
the case for the blksize, blocks, and atime fields. At the
moment the authoritative values are still stored in the znode.
This patch introduces an optimized zfs_getattr_fast() call.
The idea is to use the up to date values from the inode and
the blksize, block, and atime fields from the znode. At some
latter date we should be able to strictly use the inode values
and further improve performance.
The remaining overhead in the zfs_getattr_fast() call can be
attributed to having to take the znode mutex. This overhead is
unavoidable until the inode is kept strictly up to date. The
the careful reader will notice the we do not use the customary
ZFS_ENTER()/ZFS_EXIT() macros. These macro's are designed to
ensure the filesystem is not torn down in the middle of an
operation. However, in this case the VFS is holding a
reference on the active inode so we know this is impossible.
=================== Performance Tests ========================
This test calls the fstat(2) system call 10,000,000 times on
an open file description in a tight loop. The test results
show the zfs stat(2) performance is now only 22% slower than
ext4. This is a 2.5x improvement and there is a clear long
term plan to get to parity with ext4.
filesystem | test-1 test-2 test-3 | average | times-ext4
--------------+-------------------------+---------+-----------
ext4 | 7.785s 7.899s 7.284s | 7.656s | 1.000x
zfs-0.6.0-rc4 | 24.052s 22.531s 23.857s | 23.480s | 3.066x
zfs-faststat | 9.224s 9.398s 9.485s | 9.369s | 1.223x
The second test is to run 'du' of a copy of the /usr tree
which contains 110514 files. The test is run multiple times
both using both a cold cache (/proc/sys/vm/drop_caches) and
a hot cache. As expected this change signigicantly improved
the zfs hot cache performance and doesn't quite bring zfs to
parity with ext4.
A little surprisingly the zfs cold cache performance is better
than ext4. This can probably be attributed to the zfs allocation
policy of co-locating all the meta data on disk which minimizes
seek times. By default the ext4 allocator will spread the data
over the entire disk only co-locating each directory.
filesystem | cold | hot
--------------+---------+--------
ext4 | 13.318s | 1.040s
zfs-0.6.0-rc4 | 4.982s | 1.762s
zfs-faststat | 4.933s | 1.345s
Under Linux you may only disable USER xattrs. The SECURITY,
SYSTEM, and TRUSTED xattr namespaces must always be available
if xattrs are supported by the filesystem. The enforcement
of USER xattrs is performed in the zpl_xattr_user_* handlers.
Under Solaris there is only a single xattr namespace which
is managed globally.
The Linux kernel already has support for mandatory locking. This
change just replaces the Solaris mandatory locking calls with the
Linux equivilants. In fact, it looks like this code could be
removed entirely because this checking is already done generically
in the Linux VFS. However, for now we'll leave it in place even
if it is redundant just in case we missed something.
The original patch to update the code to support mandatory locking
was done by Rohan Puri. This patch is an updated version which is
compatible with the previous mount option handling changes.
Original-Patch-by: Rohan Puri <rohan.puri15@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#222Closes#253
The .get_sb callback has been replaced by a .mount callback
in the file_system_type structure. When using the new
interface the caller must now use the mount_nodev() helper.
Unfortunately, the new interface no longer passes the vfsmount
down to the zfs layers. This poses a problem for the existing
implementation because we currently save this pointer in the
super block for latter use. It provides our only entry point
in to the namespace layer for manipulating certain mount options.
This needed to be done originally to allow commands like
'zfs set atime=off tank' to work properly. It also allowed me
to keep more of the original Solaris code unmodified. Under
Solaris there is a 1-to-1 mapping between a mount point and a
file system so this is a fairly natural thing to do. However,
under Linux they many be multiple entries in the namespace
which reference the same filesystem. Thus keeping a back
reference from the filesystem to the namespace is complicated.
Rather than introduce some ugly hack to get the vfsmount and
continue as before. I'm leveraging this API change to update
the ZFS code to do things in a more natural way for Linux.
This has the upside that is resolves the compatibility issue
for the long term and fixes several other minor bugs which
have been reported.
This commit updates the code to remove this vfsmount back
reference entirely. All modifications to filesystem mount
options are now passed in to the kernel via a '-o remount'.
This is the expected Linux mechanism and allows the namespace
to properly handle any options which apply to it before passing
them on to the file system itself.
Aside from fixing the compatibility issue, removing the
vfsmount has had the benefit of simplifying the code. This
change which fairly involved has turned out nicely.
Closes#246Closes#217Closes#187Closes#248Closes#231
Under Linux the VFS handles virtually all of the mmap() access
checks. Filesystem specific checks are left to be handled in
the .mmap() hook and normally there arn't any.
However, ZFS provides a few attributes which can influence the
mmap behavior and should be honored. Note, currently the code
to modify these attributes has not been implemented under Linux.
* ZFS_IMMUTABLE | ZFS_READONLY | ZFS_APPENDONLY: when any of these
attributes are set a file may not be mmaped with write access.
* ZFS_AV_QUARANTINED: when set a file file may not be mmaped with
read or exec access.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The following functions were required for the OpenSolaris mmap
implementation. Because the Linux VFS does most the most heavy
lifting for us they are not required and are being removed to
keep the code clean and easy to understand.
* zfs_null_putapage()
* zfs_frlock()
* zfs_no_putpage()
Signed-off-by: Brian Behlendorf <behlendorf@llnl.gov>
Enable zfs_getpage, zfs_fillpage, zfs_putpage, zfs_putapage functions.
The functions have been modified to make them Linux friendly.
ZFS uses these functions to read/write the mmapped pages. Using them
from readpage/writepage results in clear code. The patch also adds
readpages and writepages interface functions to read/write list of
pages in one function call.
The code change handles the first mmap optimization mentioned on
https://github.com/behlendorf/zfs/issues/225
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Signed-off-by: Brian Behlendorf <behlendorf@llnl.gov>
Issue #255
According to Linux kernel commit 2c27c65e, using truncate_setsize in
setattr simplifies the code. Therefore, the patch replaces the call
to vmtruncate() with truncate_setsize().
zfs_setattr uses zfs_freesp to free the disk space belonging to the
file. As truncate_setsize may release the page cache and flushing
the dirty data to disk, it must be called before the zfs_freesp.
Suggested-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Closes#255
The comment in zfs_close() pertaining to decrementing the synchronous
open count needs to be updated for Linux. The code was already
updated to be correct, but the comment was missed and is now misleading.
Under Linux the zfs_close() hook is only called once when the final
reference is dropped. This differs from Solaris where zfs_close()
is called for each close.
Closes#237
This commit adds module options for all existing zfs tunables.
Ideally the average user should never need to modify any of these
values. However, in practice sometimes you do need to tweak these
values for one reason or another. In those cases it's nice not to
have to resort to rebuilding from source. All tunables are visable
to modinfo and the list is as follows:
$ modinfo module/zfs/zfs.ko
filename: module/zfs/zfs.ko
license: CDDL
author: Sun Microsystems/Oracle, Lawrence Livermore National Laboratory
description: ZFS
srcversion: 8EAB1D71DACE05B5AA61567
depends: spl,znvpair,zcommon,zunicode,zavl
vermagic: 2.6.32-131.0.5.el6.x86_64 SMP mod_unload modversions
parm: zvol_major:Major number for zvol device (uint)
parm: zvol_threads:Number of threads for zvol device (uint)
parm: zio_injection_enabled:Enable fault injection (int)
parm: zio_bulk_flags:Additional flags to pass to bulk buffers (int)
parm: zio_delay_max:Max zio millisec delay before posting event (int)
parm: zio_requeue_io_start_cut_in_line:Prioritize requeued I/O (bool)
parm: zil_replay_disable:Disable intent logging replay (int)
parm: zfs_nocacheflush:Disable cache flushes (bool)
parm: zfs_read_chunk_size:Bytes to read per chunk (long)
parm: zfs_vdev_max_pending:Max pending per-vdev I/Os (int)
parm: zfs_vdev_min_pending:Min pending per-vdev I/Os (int)
parm: zfs_vdev_aggregation_limit:Max vdev I/O aggregation size (int)
parm: zfs_vdev_time_shift:Deadline time shift for vdev I/O (int)
parm: zfs_vdev_ramp_rate:Exponential I/O issue ramp-up rate (int)
parm: zfs_vdev_read_gap_limit:Aggregate read I/O over gap (int)
parm: zfs_vdev_write_gap_limit:Aggregate write I/O over gap (int)
parm: zfs_vdev_scheduler:I/O scheduler (charp)
parm: zfs_vdev_cache_max:Inflate reads small than max (int)
parm: zfs_vdev_cache_size:Total size of the per-disk cache (int)
parm: zfs_vdev_cache_bshift:Shift size to inflate reads too (int)
parm: zfs_scrub_limit:Max scrub/resilver I/O per leaf vdev (int)
parm: zfs_recover:Set to attempt to recover from fatal errors (int)
parm: spa_config_path:SPA config file (/etc/zfs/zpool.cache) (charp)
parm: zfs_zevent_len_max:Max event queue length (int)
parm: zfs_zevent_cols:Max event column width (int)
parm: zfs_zevent_console:Log events to the console (int)
parm: zfs_top_maxinflight:Max I/Os per top-level (int)
parm: zfs_resilver_delay:Number of ticks to delay resilver (int)
parm: zfs_scrub_delay:Number of ticks to delay scrub (int)
parm: zfs_scan_idle:Idle window in clock ticks (int)
parm: zfs_scan_min_time_ms:Min millisecs to scrub per txg (int)
parm: zfs_free_min_time_ms:Min millisecs to free per txg (int)
parm: zfs_resilver_min_time_ms:Min millisecs to resilver per txg (int)
parm: zfs_no_scrub_io:Set to disable scrub I/O (bool)
parm: zfs_no_scrub_prefetch:Set to disable scrub prefetching (bool)
parm: zfs_txg_timeout:Max seconds worth of delta per txg (int)
parm: zfs_no_write_throttle:Disable write throttling (int)
parm: zfs_write_limit_shift:log2(fraction of memory) per txg (int)
parm: zfs_txg_synctime_ms:Target milliseconds between tgx sync (int)
parm: zfs_write_limit_min:Min tgx write limit (ulong)
parm: zfs_write_limit_max:Max tgx write limit (ulong)
parm: zfs_write_limit_inflated:Inflated tgx write limit (ulong)
parm: zfs_write_limit_override:Override tgx write limit (ulong)
parm: zfs_prefetch_disable:Disable all ZFS prefetching (int)
parm: zfetch_max_streams:Max number of streams per zfetch (uint)
parm: zfetch_min_sec_reap:Min time before stream reclaim (uint)
parm: zfetch_block_cap:Max number of blocks to fetch at a time (uint)
parm: zfetch_array_rd_sz:Number of bytes in a array_read (ulong)
parm: zfs_pd_blks_max:Max number of blocks to prefetch (int)
parm: zfs_dedup_prefetch:Enable prefetching dedup-ed blks (int)
parm: zfs_arc_min:Min arc size (ulong)
parm: zfs_arc_max:Max arc size (ulong)
parm: zfs_arc_meta_limit:Meta limit for arc size (ulong)
parm: zfs_arc_reduce_dnlc_percent:Meta reclaim percentage (int)
parm: zfs_arc_grow_retry:Seconds before growing arc size (int)
parm: zfs_arc_shrink_shift:log2(fraction of arc to reclaim) (int)
parm: zfs_arc_p_min_shift:arc_c shift to calc min/max arc_p (int)
Move 'bulk' and 'xattr_bulk' from the stack to the heap to minimize
stack space usage. These two arrays consumed 448 bytes on the stack
and have been replaced by two 8 byte points for a total stack space
saving of 432 bytes. The zfs_setattr() path had been previously
observed to overrun the stack in certain circumstances.
In the original implementation the zfs_open()/zfs_close() hooks
were dropped for simplicity. This was functional but not 100%
correct with the expected ZFS sematics. Updating and re-adding the
zfs_open()/zfs_close() hooks resolves the following issues.
1) The ZFS_APPENDONLY file attribute is once again honored. While
there are still no Linux tools to set/clear these attributes once
there are it should behave correctly.
2) Minimal virus scan file attribute hooks were added. Once again
this support in disabled but the infrastructure is back in place.
3) Most importantly correctly handle assigning files which were
opened syncronously to the intent log. Without this change O_SYNC
modifications could be lost during a system crash even though they
were marked synchronous.
Filesystems like ZFS must use what the kernel calls an anonymous super
block. Basically, this is just a filesystem which is not backed by a
single block device. Normally this block device's dev_t is stored in
the super block. For anonymous super blocks a unique reserved dev_t
is assigned as part of get_sb().
This sb->s_dev must then be set in the returned stat structures as
stat->st_dev. This allows userspace utilities to easily detect the
boundries of a specific filesystem. Tools such as 'du' depend on this
for proper accounting.
Additionally, under OpenSolaris the statfs->f_fsid is set to the device
id. To preserve consistency with OpenSolaris we also set the fsid to
the device id. Other Linux filesystem (ext) set the fsid to a unique
value determined by the filesystems uuid. This value is unique but
maintains no relationship to the device id. This may be desirable
when exporting NFS filesystem because it minimizes to chance of a
client observing the same fsid from two different servers.
Closes#140
Move 'tmpxvattr' from the stack to the heap to minimize stack
space usage. This is enough to get us below the 1024 byte stack
frame warning. That however is still a large stack frame and it
should be further reduced by moving the 'bulk' and 'xattr_bulk'
sa_bulk_attr_t variables to the heap in a future patch.
When I began work on the Posix layer it immediately became clear to
me that to integrate cleanly with the Linux VFS certain Solaris
specific things would have to go. One of these things was to elimate
as many Solaris specific types from the ZPL layer as possible. They
would be replaced with their Linux equivalents. This would not only
be good for performance, but for the general readability and health of
the code. The Solaris and Linux VFS are different beasts and should
be treated as such. Most of the code remains common for constructing
transactions and such, but there are subtle and important differenced
which need to be repsected.
This policy went quite for for certain types such as the vnode_t,
and it initially seemed to be working out well for the vattr_t. There
was a relatively small amount of related xvattr_t code I was forced to
comment out with HAVE_XVATTR. But it didn't look that hard to come
back soon and replace it all with a native Linux type.
However, after going doing this path with xvattr some distance it
clear that this code was woven in the ZPL more deeply than I thought.
In particular its hooks went very deep in to the ZPL replay code
and replacing it would not be as easy as I originally thought.
Rather than continue persuing replacing and removing this code I've
taken a step back and reevaluted things. This commit reverts many of
my previous commits which removed xvattr related code. It restores
much of the code to its original upstream state and now relies on
improved xvattr_t support in the zfs package itself.
The result of this is that much of the code which I had commented
out, which accidentally broke things like replay, is now back in
place and working. However, there may be a small performance
impact for getattr/setattr operations because they now require
a translation from native Linux to Solaris types. For now that's
a price I'm willing to pay. Once everything is completely functional
we can revisting the issue of removing the vattr_t/xvattr_t types.
Closes#111
ASSERT3P should be used instead of ASSERT3U when comparing
pointers. Using ASSERT3U with the cast causes a compiler
warning for 32-bit builds which is fatal with --enable-debug.
Because the secpolicy_* macros are all currently defined to (0).
And because the caller of this function does not check the return
code. The compiler complains that this statement has no effect
which is correct and OK. To suppress the warning explictly cast
the result to (void).
When changing the uid/gid of a file via zfs_setattr() use the
Posix id passed in iattr->ia_uid/gid. While the zfs_fuid_create()
code already had the fuid support disabled for Linux it was
returning the uid/gid from the credential. With this change
the 'chown' command which relies on setxattr is now working
properly.
Also remove a little stray white space which was in front of
zfs_update_inode() call and the end of zfs_setattr().
Under Linux sys_symlink(2) should result in a inode being created
with one reference for the inode itself, and a second reference on
the inode which is held by the new dentry. Under Solaris this
appears not to be the case. Their zfs_symlink() handler drops
the inode reference before returning.
The result of this under Linux is that the reference count for
symlinks is always one smaller than it should have been. This
results in a BUG() when the symlink is unlinked. To handle this
the Linux port now keeps the inode reference which differs from
the Solaris behavior. This results in correct reference counts.
Closes#96
This patch addresses three issues related to symlinks.
1) Revert the zfs_follow_link() function to a modified version
of the original zfs_readlink(). The only changes from the
original OpenSolaris version relate to using Linux types.
For the moment this means no vnode's and no zfsvfs_t. The
caller zpl_follow_link() was also updated accordingly. This
change was reverted because it was slightly gratuitious.
2) Update zpl_follow_link() to use local variables for the
link buffer. I'd forgotten that iov.iov_base is updated by
uiomove() so after the call to zfs_readlink() it can not longer
be used. We need our own private copy of the link pointer.
3) Allocate MAXPATHLEN instead of MAXPATHLEN+1. By default
MAXPATHLEN is 4096 bytes which is a full page, adding one to
it pushes it slightly over a page. That means you'll likely
end up allocating 2 pages which is wasteful of memory and
possibly slightly slower.
The new prefered inteface for evicting an inode from the inode cache
is the ->evict_inode() callback. It replaces both the ->delete_inode()
and ->clear_inode() callbacks which were previously used for this.
It's worth taking a moment to describe how mmap is implemented
for zfs because it differs considerably from other Linux filesystems.
However, this issue is handled the same way under OpenSolaris.
The issue is that by design zfs bypasses the Linux page cache and
leaves all caching up to the ARC. This has been shown to work
well for the common read(2)/write(2) case. However, mmap(2)
is problem because it relies on being tightly integrated with the
page cache. To handle this we cache mmap'ed files twice, once in
the ARC and a second time in the page cache. The code is careful
to keep both copies synchronized.
When a file with an mmap'ed region is written to using write(2)
both the data in the ARC and existing pages in the page cache
are updated. For a read(2) data will be read first from the page
cache then the ARC if needed. Neither a write(2) or read(2) will
will ever result in new pages being added to the page cache.
New pages are added to the page cache only via .readpage() which
is called when the vfs needs to read a page off disk to back the
virtual memory region. These pages may be modified without
notifying the ARC and will be written out periodically via
.writepage(). This will occur due to either a sync or the usual
page aging behavior. Note because a read(2) of a mmap'ed file
will always check the page cache first even when the ARC is out
of date correct data will still be returned.
While this implementation ensures correct behavior it does have
have some drawbacks. The most obvious of which is that it
increases the required memory footprint when access mmap'ed
files. It also adds additional complexity to the code keeping
both caches synchronized.
Longer term it may be possible to cleanly resolve this wart by
mapping page cache pages directly on to the ARC buffers. The
Linux address space operations are flexible enough to allow
selection of which pages back a particular index. The trick
would be working out the details of which subsystem is in
charge, the ARC, the page cache, or both. It may also prove
helpful to move the ARC buffers to a scatter-gather lists
rather than a vmalloc'ed region.
Additionally, zfs_write/read_common() were used in the readpage
and writepage hooks because it was fairly easy. However, it
would be better to update zfs_fillpage and zfs_putapage to be
Linux friendly and use them instead.
I appologize in advance why to many things ended up in this commit.
When it could be seperated in to a whole series of commits teasing
that all apart now would take considerable time and I'm not sure
there's much merrit in it. As such I'll just summerize the intent
of the changes which are all (or partly) in this commit. Broadly
the intent is to remove as much Solaris specific code as possible
and replace it with native Linux equivilants. More specifically:
1) Replace all instances of zfsvfs_t with zfs_sb_t. While the
type is largely the same calling it private super block data
rather than a zfsvfs is more consistent with how Linux names
this. While non critical it makes the code easier to read when
your thinking in Linux friendly VFS terms.
2) Replace vnode_t with struct inode. The Linux VFS doesn't have
the notion of a vnode and there's absolutely no good reason to
create one. There are in fact several good reasons to remove it.
It just adds overhead on Linux if we were to manage one, it
conplicates the code, and it likely will lead to bugs so there's
a good change it will be out of date. The code has been updated
to remove all need for this type.
3) Replace all vtype_t's with umode types. Along with this shift
all uses of types to mode bits. The Solaris code would pass a
vtype which is redundant with the Linux mode. Just update all the
code to use the Linux mode macros and remove this redundancy.
4) Remove using of vn_* helpers and replace where needed with
inode helpers. The big example here is creating iput_aync to
replace vn_rele_async. Other vn helpers will be addressed as
needed but they should be be emulated. They are a Solaris VFS'ism
and should simply be replaced with Linux equivilants.
5) Update znode alloc/free code. Under Linux it's common to
embed the inode specific data with the inode itself. This removes
the need for an extra memory allocation. In zfs this information
is called a znode and it now embeds the inode with it. Allocators
have been updated accordingly.
6) Minimal integration with the vfs flags for setting up the
super block and handling mount options has been added this
code will need to be refined but functionally it's all there.
This will be the first and last of these to large to review commits.
This code is used for snapshot and heavily leverages Solaris
functionality we do not want to reimplement. These files have
been removed, including references to them, and will be replaced
by a zfs_snap.c/zpl_snap.c implementation which handles snapshots.
For the moment we have left ZFS unchanged and it updates many values
as part of the znode. However, some of these values should be set
in the inode. For the moment this is handled by adding a function
called zfs_inode_update() which updates the inode based on the znode.
This is considered a workaround until we can systematically go
through the ZFS code and have it directly update the inode. At
which point zfs_update_inode() can be dropped entirely. Keeping
two copies of the same data isn't only inefficient it's a breeding
ground for bugs.
These compiler warnings were introduced when code which was
previously #ifdef'ed out by HAVE_ZPL was re-added for use
by the posix layer. All of the following changes should be
obviously correct and will cause no semantic changes.
