The ip6_output routine is missing L2 cache invalication as done
in ip_output. Even with that code, some problems with UDP over
IPv6 have been reported. Diabling L2 cache for that problem works
around the problem for now.
PR: 211872 211926
Reviewed by: gnn
Approved by: gnn (mentor)
MFC after: immediate
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
_prison_check_ip4 renamed to prison_check_ip4_locked
Move IPv6-specific jail functions to new file netinet6/in6_jail.c
_prison_check_ip6 renamed to prison_check_ip6_locked
Add appropriate prototypes to sys/sys/jail.h
Adjust kern_jail.c to call prison_check_ip4_locked and
prison_check_ip6_locked accordingly.
Add netinet/in_jail.c and netinet6/in6_jail.c to the list of files that
need to be built when INET and INET6, respectively, are configured in the
kernel configuration file.
Reviewed by: jtl
Approved by: sjg (mentor)
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D6799
- Re-write tcp_ctlinput6() to closely mimic the IPv4 tcp_ctlinput()
- Now that tcp_ctlinput6() updates t_maxseg, we can allow ip6_output()
to send TCP packets without looking at the tcp host cache for every
single transmit.
- Make the icmp6 code mimic the IPv4 code & avoid returning
PRC_HOSTDEAD because it is so expensive.
Without these changes in place, every TCP6 pmtu discovery or host
unreachable ICMP resulted in a call to in6_pcbnotify() which walks the
tcbinfo table with the write lock held. Because the tcbinfo table is
shared between IPv4 and IPv6, this causes huge scalabilty issues on
servers with lots of (~100K) TCP connections, to the point where even
a small percent of IPv6 traffic had a disproportionate impact on
overall throughput.
Reviewed by: bz, rrs, ae (all earlier versions), lstewart (in Netflix's tree)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D7272
- Move cr_canseeinpcb to sys/netinet/in_prot.c in order to separate the
INET and INET6-specific code from the rest of the prot code (It is only
used by the network stack, so it makes sense for it to live with the
other network stack code.)
- Move cr_canseeinpcb prototype from sys/systm.h to netinet/in_systm.h
- Rename cr_seeotheruids to cr_canseeotheruids and cr_seeothergids to
cr_canseeothergids, make them non-static, and add prototypes (so they
can be seen/called by in_prot.c functions.)
- Remove sw_csum variable from ip6_forward in ip6_forward.c, as it is an
unused variable.
Reviewed by: gnn, jtl
Approved by: sjg (mentor)
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D2901
r301217 re-added per-connection L2 caching from a previous change,
but it omitted caching in the fast path. Add it.
Reviewed By: gallatin
Approved by: gnn (mentor)
Differential Revision: https://reviews.freebsd.org/D7239
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
loaded, and syncthing is started, which uses setsockopt(IPV6_PKGINFO).
This is because pflog interfaces do not normally have an IPv6 address,
causing the ND_IFINFO() macro to dereference a NULL pointer.
Reviewed by: ae
PR: 210943
MFC after: 3 days
than removing the network interfaces first. This change is rather larger
and convoluted as the ordering requirements cannot be separated.
Move the pfil(9) framework to SI_SUB_PROTO_PFIL, move Firewalls and
related modules to their own SI_SUB_PROTO_FIREWALL.
Move initialization of "physical" interfaces to SI_SUB_DRIVERS,
move virtual (cloned) interfaces to SI_SUB_PSEUDO.
Move Multicast to SI_SUB_PROTO_MC.
Re-work parts of multicast initialisation and teardown, not taking the
huge amount of memory into account if used as a module yet.
For interface teardown we try to do as many of them as we can on
SI_SUB_INIT_IF, but for some this makes no sense, e.g., when tunnelling
over a higher layer protocol such as IP. In that case the interface
has to go along (or before) the higher layer protocol is shutdown.
Kernel hhooks need to go last on teardown as they may be used at various
higher layers and we cannot remove them before we cleaned up the higher
layers.
For interface teardown there are multiple paths:
(a) a cloned interface is destroyed (inside a VIMAGE or in the base system),
(b) any interface is moved from a virtual network stack to a different
network stack ("vmove"), or (c) a virtual network stack is being shut down.
All code paths go through if_detach_internal() where we, depending on the
vmove flag or the vnet state, make a decision on how much to shut down;
in case we are destroying a VNET the individual protocol layers will
cleanup their own parts thus we cannot do so again for each interface as
we end up with, e.g., double-frees, destroying locks twice or acquiring
already destroyed locks.
When calling into protocol cleanups we equally have to tell them
whether they need to detach upper layer protocols ("ulp") or not
(e.g., in6_ifdetach()).
Provide or enahnce helper functions to do proper cleanup at a protocol
rather than at an interface level.
Approved by: re (hrs)
Obtained from: projects/vnet
Reviewed by: gnn, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6747
The SIOCSIFALIFETIME_IN6 provided by the kame project is unused,
it can't really be used safely and has been completely removed from
NetBSD and OpenBSD.
Obtained from: NetBSD (kern/35897)
PR: 210148 (exp-run)
Reviewed by: ae, hrs
Relnotes: yes
Approved by: re (glebius)
Differential Revision: https://reviews.freebsd.org/D5491
Add accessor functions to toggle the state per VNET.
The base system (vnet0) will always enable itself with the normal
registration. We will share the registered protocol handlers in all
VNETs minimising duplication and management.
Upon disabling netisr processing for a VNET drain the netisr queue from
packets for that VNET.
Update netisr consumers to (de)register on a per-VNET start/teardown using
VNET_SYS(UN)INIT functionality.
The change should be transparent for non-VIMAGE kernels.
Reviewed by: gnn (, hiren)
Obtained from: projects/vnet
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6691
but removed due to other changes in the system. Restore the llentry pointer
to the "struct route", and use it to cache the L2 lookup (ARP or ND6) as
appropriate.
Submitted by: Mike Karels
Differential Revision: https://reviews.freebsd.org/D6262
Otherwise we transmit the first neighbour solicitation in the context of the
caller of nd6_dad_start(), which can easily result in lock recursion. When
DAD is to be started after some delay, we send the first NS from the DAD
callout handler, so just change the implementation to do this in the
non-delayed case as well.
Reviewed by: ae, hrs
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6639
specific order. VNET_SYSUNINITs however are doing exactly that.
Thus remove the VIMAGE conditional field from the domain(9) protosw
structure and replace it with VNET_SYSUNINITs.
This also allows us to change some order and to make the teardown functions
file local static.
Also convert divert(4) as it uses the same mechanism ip(4) and ip6(4) use
internally.
Slightly reshuffle the SI_SUB_* fields in kernel.h and add a new ones, e.g.,
for pfil consumers (firewalls), partially for this commit and for others
to come.
Reviewed by: gnn, tuexen (sctp), jhb (kernel.h)
Obtained from: projects/vnet
MFC after: 2 weeks
X-MFC: do not remove pr_destroy
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6652
This is required to signal connetion setup on non-blocking sockets
via becoming writable. This still allows for implicit connection
setup.
MFC after: 1 week
from mbuf when calculating path mtu. Remove now unused finaldst variable.
Also constify dst argument in ip6_getpmtu() and ip6_getpmtu_ctl().
Reviewed by: melifaro
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
icmp6.redirtimeout, icmp6.nd6_maxnudhint and ip6.rr_prune are left
undocumented as they appear to have no effect. Some existing sysctl
descriptions were modified for consistency and style, and the
ip6.tempvltime and ip6.temppltime handlers were rewritten to be a bit
simpler and to avoid setting the sysctl value before validating it.
MFC after: 3 weeks
nd6_prelist_add() sets *newp if and only if it is successful, so there's no
need for code that handles the case where the return value is 0 and
*newp == NULL. Fix some style bugs in nd6_prelist_add() while here.
MFC after: 1 week
chunk, enable UDP encapsulation for all those addresses.
This helps clients using a userland stack to support multihoming if
they are not behind a NAT.
MFC after: 1 week
interested in having tunneled UDP and finding out about the
ICMP (tested by Michael Tuexen with SCTP.. soon to be using
this feature).
Differential Revision: http://reviews.freebsd.org/D5875
Currently we don't keep zoneid in in6_ifaddr structure, because there
is still some code, that doesn't properly initialize sin6_scope_id,
but some functions use sa_equal() for addresses comparison. sa_equal()
compares full sockaddr_in6 structures and such comparison will fail.
For now use zero zoneid in in6ifa_ifwithaddr(). It is safe, because
used address is in embedded form. In future we will use zoneid, so mark it
with XXX comment.
Reported by: kp
Tested by: kp
