This allows boot to proceed on a real system until the issue
of calling back into certain OpenFirmware calls (e.g. finddevice)
in thread context is understood.
(this commit only affects psim users, of which I think I am the
only one...)
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
into single-user mode (as seen on sparc64 and PPC). Problems were due
to a minor oversight in the changes committed in revision 1.25.
Submitted by: grehan
Tested by: gad & yongari
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
for unknown events.
A number of modules return EINVAL in this instance, and I have left
those alone for now and instead taught MOD_QUIESCE to accept this
as "didn't do anything".
o Make debugging code conditional upon KDB instead of DDB.
o Call kdb_alt_break() instead of db_alt_break().
o Call kdb_enter() instead of breakpoint().
Ultra2 users may want to set OFWCONS_POLL_HZ to a value of '20'.
I have left default value at '4' as higher values can consume a more
than is acceptable amount of CPU, and we don't have a consensus yet
what is an optimal value.
Submitted by: Pyun YongHyeon <yongari@kt-is.co.kr>
identifiers, to openfirmio.h as OFIOCMAXNAME, so programs can use it
for buffer sizes etc.
Note: Although this is only a rough upper limit to make the code more
robust and to prevent the allocation of ridiculous amounts of memory,
the current limit of one page (8191 + '\0' in openfirm_getstr()) still
appears a bit high. The maximum length of OFW property names is 31.
I didn't find a maximum length for the device identifiers in the OFW
documentation but it certainly is much smaller than 8191, too.
- Enable the OFIOCSET ioctl, i.e. move it out from under #if 0.
- Don't use openfirm_getstr() for the property value in OFIOCSET, there
are also properties whose values aren't strings and it makes sense to
use a different maximum length for property values than OFW_NAME_MAX/
OFIOCMAXNAME. The maximum accepted property value is defined in
openfirmio.h as OFIOCMAXVALUE (currently the maximum size of the value
of the nvramrc property).
- Make OFIOCSET not return EINVAL when OF_setprop() returns a different
length for the written value than it was told to write, this is normal
for the text string values of the properties in the OFW /options node.
Instead, only return EINVAL if OF_setprop() returned -1 (value could
not be written or property could not be created). Add a comment about
the specialty of the OFW /options node.
- Make OFIOCSET return the length of the written value returned by
OF_setprop(), just like OF_getprop() does. Quite useful, at least for
debugging.
Reviewed by: tmm
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Add missing D_TTY flags to various drivers.
Complete asserts that dev_t's passed to ttyread(), ttywrite(),
ttypoll() and ttykqwrite() have (d_flags & D_TTY) and a struct tty
pointer.
Make ttyread(), ttywrite(), ttypoll() and ttykqwrite() the default
cdevsw methods for D_TTY drivers and remove the explicit initializations
in various drivers cdevsw structures.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
the psim simulator. Look for the "file" property which only exists
on psim disks, and as a bonus, print the contents of this at boot-time,
which is the host file being used for the disk image.
- remove remaining warnings.
provide no methods does not make any sense, and is not used by any
driver.
It is a pretty hard to come up with even a theoretical concept of
a device driver which would always fail open and close with ENODEV.
Change the defaults to be nullopen() and nullclose() which simply
does nothing.
Remove explicit initializations to these from the drivers which
already used them.
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
dev_t to the method functions.
The dev_t can still be found at struct consdev *->cn_dev.
Add a void *cn_arg element to struct consdev which the drivers can use
for retrieving their softc.
handy if the machine is on another floor. A minor issue with this is that
these functions are also used by the debugger, so its possible to break into
the debugger from the debugger.
PR: sparc64/47143
Reviewed by: benno
Approved by: jake (mentor)
name of the device that it creates. Update /etc/ttys accordingly.
An alias is created for the old name so that old /etc/ttys will continue to
work, but due to aliases being implemented as symlinks in devfs you cannot
login as root when using the alias device.
Discussed with: grehan
