is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
totally dynamic.
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
For those where it was easy, drivers were also fixed to call
dev_attach() during probe rather than attach (in keeping with the
new design articulated in a mail message five months ago). For
a few that were really easy, correct state tracking was added as well.
The `fd' driver was fixed to correctly fill in the description.
The CPU identify code was fixed to attach a `cpu' device. The code
was also massively reordered to fill in cpu_model with somethingremotely
resembling what identifycpu() prints out. A few bytes saved by using
%b to format the features list rather than lots of ifs.
Would you please commit this two-line patch to /sys/i386/isa/b004.c
(the Transputer driver) so that it at least compiles under 2.x
Haven't tried if the driver is working properly, but a kernel with
compiled-in driver has been running for two days now with no apparent
problems.
Submitted by: luigi
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
