usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
getpid, getuid, getgid and pipe, since they bootstrapped from
OSF/1 and never cleaned up. Switch to the native syscalls
on alpha so that the above functions work
MFC after: 7 days
extensively as none of my testboxes have speakers or an audio source at
present, but the chains built look correct and reading /dev/audio (ulaw,
translated from signed 16 bit little-endian) gives values within the
expected range for silence.
default format for the chosen subdevice cannot be obtained return an error
instead of returning success with an indeteterminate format selected.
note that this should never happen once the feederchain builder works for
recording.
which small and/or nearly full filesystems would fail with `file
system full' messages when trying to replace a number of existing
files (for example during a system installation). When the allocation
routines are about to fail with a file system full condition, they
make a call to softdep_request_cleanup() which attempts to accelerate
the flushing of pending deletion requests in an effort to free up
space. In the face of filesystem I/O requests that exceed the
available disk transfer capacity, the cleanup request could take
an unbounded amount of time. Thus, the softdep_request_cleanup()
routine will only try for tickdelay seconds (default 2 seconds)
before giving up and returning a filesystem full error. Under typical
conditions, the softdep_request_cleanup() routine is able to free
up space in under fifty milliseconds.
- Clear the cached destination before getting another cached route.
Otherwise, garbage in the padding space (which might be filled in if it was
used for IPv4) could annoy rtalloc.
Obtained from: KAME
ohci.c: -r1.69 to 1.71
ohcireg.h: -r1.14
Some of these deltas are based upon patches that we submitted back to
NetBSD. They got manifested slightly differently though, so I've brought
back those differences to bring our code bases closer together.
The logs from the NetBSD version of ohci.c:
revision 1.71
date: 2000/02/01 05:42:52; author: augustss; state: Exp; lines: +13 -2
Put some #ifdefs around power and shutdown hooks.
----------------------------
revision 1.70
date: 2000/01/31 22:35:13; author: augustss; state: Exp; lines: +7 -7
Rename TAILMASK to HEADMASK, since it really masks the head pointer.
From FreeBSD.
----------------------------
revision 1.69
date: 2000/01/31 22:09:13; author: augustss; state: Exp; lines: +18 -14
Change where the has table for physical-to-virtual address translation
is handled. Partly from FreeBSD.
ohci.c: -r1.68
ohcireg.h: -r1.13
date: 2000/01/31 20:17:25; author: augustss; state: Exp;
Fiddle with over-current protect when turning on port power to make
things work for some OHCI controllers.
uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
This allows obtaining crash dumps from the panics occured during late stages
of kernel initialisation before system enters into single-user mode.
MFC after: 2 weeks
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
replace mutex_lock calls on uidinfo with macro calls:
mtx_lock(&uidp->ui_mtx) -> UIDINFO_LOCK(uidp)
Terry Lambert <tlambert2@mindspring.com> helped with this.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
Integrated RAID driver, supported by <boji.t.kannanthanam@intel.com> and
<achim.leubner@intel.com>.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
This typo keeps us from properly routing an interrupt for CardBus
bridges on this machine. So, now we look for $PIR and then _PIR to
cope. With these changes, the Libretto L1 now works properly.
Evidentally, the idea comes from patch that the Japanese version of
RedHat (or against a Japanese version of Red Hat), but my Japanese
isn't good enough to to know for sure.
Reported by: Hiroyuki Aizu-san <eyes@navi.org>
# This may be an MFC candidate, but I'm not yet sure.
sleeping on a process object but changed the corresponding
wakeup()s to the thread object. The result was that non-raw
aio ops waited for an aio daemon to timeout before action
was taken. Now, we sleep on the thread object.
PR: kern/34016
operation. The vgonel() code has always called vclean() but until we
started proactively freeing vnodes it would never actually be called with
a dirty vnode, so this situation did not occur prior to the vnlru() code.
Now that we proactively free vnodes when kern.maxvnodes is hit, however,
vclean() winds up with work to do and improperly generates the warnings.
Reviewed by: peter
Approved by: re (for MFC)
MFC after: 1 day
a simple version of bcopy() so we avoid picking up the overly-complex
implementation in libc (via libstand). This is not necessary on
-current, but RELENG_4 has apparently just exceeded the 15-sector
limit for boot1.
Reviewed by: wilko
likely looking rate calculation.
Install interrupt handler before calling ich_init as the initialization
occasionally generates spurious interrupts.
These changes are derived from cg's work in progress version of this
driver.
socket so that routing daemons and other interested parties
know when an interface is attached/detached.
PR: kern/33747
Obtained from: NetBSD
MFC after: 2 weeks
db_machdep.h to fix the link failure (multiple definitions)
caused by disabling the emission of common symbols. As a result,
there were no definitions at all. While here, remove useless
declarations.
because the buffers we use could end up spanning a 64k boundary.
Unfortunately it causes too much bloat (228 -> 72 bytes free) to
just reinstate the old malloc() function.
Instead, define a structure that contains all 4 buffers which must
not cross 64k boundaries. We allocate a 64k-aligned instance in
main() using the magic that was in the old boot2 malloc() function.
This brings the free space down to 168 bytes, but that is still
better than it was before revision 1.35 (136 bytes).
Reported by: Mike Brancato <funnyguy@digitalsmackdown.net>
Pointy-hat to: iedowse
at insert time. When asking gibbs for approval for an MFC, this was
his reply:
1) It leaks memory if it can't allocate a path.
2) It defers allocation of aic->path until the call to scan the
bus. This means the path may be NULL when an interrupt occurs
prior to the call to scan the bus (stray bus reset for instance),
which will lead to a panic.
3) The driver in current doesn't recover from the failure to allocate
aic->path. The driver doesn't check during normal operation if
the path is NULL, so again a panic will result.
4) aic_cam_rescan calls malloc with M_WAITOK. aic_cam_rescan is called
from attach where it isn't necessarily safe to sleep.
5) And most importantly, it co-opts the xpt_periph from the driver level.
This was never part of the design (xpt_periph used to be static). Making
a call of this type may completely confuse the XPT if other XPT operations
are ongoing.
In the long term, Justin and Warner agreed to implement solution where
CAM itself will initiate the bus rescan if a new bus is added. For
the time being (and in particular in light of the upcoming 4.5
release), we now have camcontrol available on the boot floppy, and can
have pccardd initiate the rescan through it.
previous commit, it should always print due to lack of {} around the
second line in the if statement. The message should likely say
something more like "There's no hardware responding at this IRQ.
Device not present (or disbaled)," but that is too long. We generally
don't give elementary advise in device driver messages anyway. Be
that as it may, the problem with it printing all the time should be
corrected.
which caused incomplete snapshots to be taken. When background
fsck would run on these snapshots, the result would be files
being incorrectly released which would subsequently panic the
kernel with ``handle_workitem_freefile: inodedep survived'',
``handle_written_inodeblock: live inodedep'', and
``handle_workitem_remove: lost inodedep'' errors.
and the reference to db_regs is *extern* from alpha/include/db_machdep.h
(put it in alpha/alpha/machdep.c)- this avoids the problems we've had
about different 'common' sizes prohibiting the kernel from linking.
One to notify the system that the MTU for VLAN can be 1500 so the vlan
will automatically be configured with a 1500 MTU the other is to ignore
the error case if the received frame is to long.
The frame size notification came from code in the SIS driver, and
the support for long frames derived from the NetBSD Tulip driver.
Tested on: 4 port D-Link adapter DFE-570TX 4 Intel 21143
Netgear card with 82c169 PNIC 10/100BaseTX
Reviewed by: ru (manpage), wpaul (not objected to), archie
Approved by: imp
Obtained from: NetBSD
cpuid with %eax=1 will return a logical cpu count in bits 16-23 of %ebx.
Bit 29 is actually 'TM' according to AP-485. This signifies the presence
of the thermal control circuit (which I believe can slow the clock down
to reduce core temperature).
they make it through to userland. This should fix the p5-smp problem
without affecting the other cpus (eg: cyrix, see initcpu.c and the special
cache handling for these cpu types).
o Remove bogus flags that aren't used (if we need them in the future, we can
add them back).
o Add support for the TI-1031. This is the only YENTA compatible PCI-PCMCIA
bridge that I'm aware of (all the others are PCIC on a PCI bus, which is
different).
seem to be too short for the 500 Mhz DS20 I'm testing on. The rather
arbitrary numbers are rather bogus anyways. We should probably have
variables for these limits that are calibrated in the MD startup code
somehow.
NULL rather than curproc. Without this, if we trap early before
curthread is set, we recursively panic.
- In an SMP kernel, if we trap before curthread is set, then trap is going
to recursively panic trying to bump td->td_md.md_kernnest. The trap is
fatal anyways, so to make debugging easier just call printtrap() to
dump the trap info to the console and then halt.
involving file removal or file update were not always being fully
committed to disk. The result was lost files or corrupted file data.
This change ensures that the filesystem is properly synced to disk
before the filesystem is down-graded.
This delta also fixes a long standing bug in which a file open for
reading has been unlinked. When the last open reference to the file
is closed, the inode is reclaimed by the filesystem. Previously,
if the filesystem had been down-graded to read-only, the inode could
not be reclaimed, and thus was lost and had to be later recovered
by fsck. With this change, such files are found at the time of the
down-grade. Normally they will result in the filesystem down-grade
failing with `device busy'. If a forcible down-grade is done, then
the affected files will be revoked causing the inode to be released
and the open file descriptors to begin failing on attempts to read.
Submitted by: "Sam Leffler" <sam@errno.com>
itself, it's used outside the Linuxulator. Reimplement the
function so that its behaviour matches the current renaming
scheme. It's probably better to formalize these interdependencies.
Backout revision 1.56 and 1.57 of fifo_vnops.c.
Introduce a new poll op "POLLINIGNEOF" that can be used to ignore
EOF on a fifo, POLLIN/POLLRDNORM is converted to POLLINIGNEOF within
the FIFO implementation to effect the correct behavior.
This should allow one to view a fifo pretty much as a data source
rather than worry about connections coming and going.
Reviewed by: bde
done with boot1 on the alpha. We use 4k buffers regardless of the
actual filesystem block size.
Remove the simple malloc() implementation, as it is no longer used.
server side. This can lead to a system deadlock.
Reviewed by: iedowse
Tested by: Alexey G Misurenko <mag@caravan.ru>, iedowse
Bug found with help by: Alexey G Misurenko <mag@caravan.ru>
MFC at: earliest convenience
detect 3.3V cards for the 6710 and another method for the 6722. This
latter method is also how the 6729/6730 is supposed to detect 3.3V
cards. This method works great on my Fujitsu Stylistic 500. Sadly,
it appears that not all laptop makers are as detail oriented as the
folks that made the Stylistic. IBM Thinkpad 701C and AST Asentia 810N
both hang hard when the 6729 method is used, but at least the thinkpad
works when the 6710 method is used. The failure mode appears to be any
access to the memory that we've mapped the CIS in causes the machine to
hang until you eject the card. The Thinkpad, at least, works with this
change, and it doesn't break my Stylistic.
MFC after: 4 days
than necessary.
o Move a rarely-used goto label inside a critical section so that we don't
perform an splnet() for which there is no corresponding splx().
o Remove unnecessary splnet()/splx() around accesses to kaioinfo::kaio_jobdone
in aio_return().
o Use TAILQ_FOREACH for simple cases of iteration over kaioinfo::kaio_jobdone.
functions just grab f_data and don't muck with anything else so this
should be ok.
this fixes a panic with invariants where it thinks we've doubly initialized
the filetmp mutex even though all we've done is neglect to bzero it.
vfs.nfs.iodmaxidle (idle time before nfsiod's exit). Make it adaptive
so that we create nfsiod's on demand and they go away after not being
used for a while. The upper limit is NFS_MAXASYNCDAEMON (currently 20).
More will be done here, but this is a useful checkpoint.
Submitted by: Maxime Henrion <mux@qualys.com>
which was causing the link of the kernel to fail. Since layer4/i4b_l4mgmt.c
is always required by i4b and layer3/i4b_q931.c is only needed when a
passive card is present it makes sense to have the declaration in the
former file only.
No MFC required since the problem only became apparent after a change to
the compile options in -current which AFAIK wasn't made in -stable.
Seigo Tanimura (tanimura) posted the initial delta.
I've polished it quite a bit reducing the need for locking and
adapting it for KSE.
Locks:
1 mutex in each filedesc
protects all the fields.
protects "struct file" initialization, while a struct file
is being changed from &badfileops -> &pipeops or something
the filedesc should be locked.
1 mutex in each struct file
protects the refcount fields.
doesn't protect anything else.
the flags used for garbage collection have been moved to
f_gcflag which was the FILLER short, this doesn't need
locking because the garbage collection is a single threaded
container.
could likely be made to use a pool mutex.
1 sx lock for the global filelist.
struct file * fhold(struct file *fp);
/* increments reference count on a file */
struct file * fhold_locked(struct file *fp);
/* like fhold but expects file to locked */
struct file * ffind_hold(struct thread *, int fd);
/* finds the struct file in thread, adds one reference and
returns it unlocked */
struct file * ffind_lock(struct thread *, int fd);
/* ffind_hold, but returns file locked */
I still have to smp-safe the fget cruft, I'll get to that asap.
that va_mode of the supplied attributes is filled in with a valid
file mode (i.e not VNOVAL, and only ALLPERM bits set). However,
some NFS server op functions didn't guarantee this for all possible
request messages:
If a V3 client chose not include to a mode specification, we could
end up creating an ffs inode with mode 0177777, requiring a manual
fsck on the next reboot. Fix this by setting va_mode to 0 before
calling the VOP if a mode hasn't been supplied by the client.
In nfsrv_symlink(), S_IFMT bits supplied by a V2 client could end
up in the va_mode passed to VOP_SYMLINK with similar effects. We
now use the macro nfstov_mode() to correctly mask the bits.
motherboard chipsets. We need to force the chip to reload its MAC address
into the receive filter, and enable software access mode for the PHY.
PR: kern/33294
lost if some other process uses the lock while we are sleeping. We
restore it after we have slept. This functionality is provided by
a new routine interlocked_sleep() that wraps the interlocking with
functions that sleep. This function is then used in place of the
old ACQUIRE_LOCK_INTERLOCKED() and FREE_LOCK_INTERLOCKED() macros.
Submitted by: Debbie Chu <dchu@juniper.net>
semantics of the nfsm_reply() macro were changed so that the caller
has to explicitly handle the V2 error case, whereas before,
nfsm_reply() did a `goto nfsmout' then. A few server ops (setattr,
readlink, create, mkdir) weren't updated to match, so errors in the
V2 case could cause protocol hangs and leaked mbufs.
Correct some comments that describe the old nfsm_reply behaviour.
[older, harmless nit] Remove the unnecessary `nfsmreply0' label in
nfsrv_create(), since for its users, the main `ereply' label does
the same thing.
but since the nfs cleanup, it hasn't done so in the case where
`error' is EBADRPC. Callers of this macro expect it to initialise
*mrq, and the `nfsmout' exit point expects a reply to be allocated
if error == 0. When nfsm_reply() was called with error = EBADRPC,
whatever junk was in *mrq (often a stale pointer to an old reply
mbuf) would be assumed to be a valid reply and passed to pru_sosend(),
causing a crash sooner or later.
Fix this by allocating a reply even in the EBADRPC case like we
used to do. This bug was specific to -current.
intermodule communication is done via kobj calls. If anything
currently depends on them, let it break so that we can fix it. Maybe
we'll need to export some of the card_if.c or power_if.c symbols, but
I think those should be in the base kernel (since all *_if.c should be
in the base kernel for just these reasons).
in softdep_sync_metadata(). Otherwise we may miss dependencies
that need to be flushed which will result in a later panic
with the message ``vinvalbuf: dirty bufs''.
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
MFC after: 1 week
larger than 8k. We now use 4k buffers regardless of the filesystem
block size, so there is no longer a static limit.
Simply increasing the buffer size from 8k to 16k as done on the
i386 doesn't work on the alpha, probably because it causes us
to overshoot boot1's 48k runtime memory limit.
Tested by: naddy
are checked on the way in even if they were not calculated on the
way out.
This fixes rwhod
PR: 31954
Submitted by: fenner
Approved by: fenner
MFC after: 1 week
(We should be able to handle locally originated IP packets, and
these do not have m_pkthdr.rcvif set.)
PR: kern/32806, kern/33766
Reviewed by: luigi
Fix tested by: Maxim Konovalov <maxim@macomnet.ru>,
Erwin Lansing <erwin@lansing.dk>
defined, no symbols are exported from the module. This is
the typical configuration for most device drivers and
standalone modules; only infrastructure modules or those with
special requirements typically need to export symbols.
Don't print the objcopy commands as they are run when converting
symbols; they're bulky and annoying in many cases.
All the alpha loaders should use the same version file. Also, we might
should merge the various loaders (cdboot, loader, netboot) into one loader
that can boot off of disks, CD's, and network devices. The version bump
is needed so the FICL scripts won't bomb out thinking that the netboot
binary is too old.
backing out the 1024 sector boot0, but revision 1.12 had nothing to do with
that. Instead, it documented various compile time options for boot0 and
allowed them to be overridden via make.conf or options on the make
command line.
We calculate a trigger point that both guarentees we will find a
sufficient number of vnodes to recycle and prevents us from recycling
vnodes with lots of resident pages. This particular section of
code is designed to recycle vnodes, not do unnecessary frees of
cached VM pages.
been removed from the cache-list as part of a previous unmount.
This would result in panics (page fault in dqflush()) during subsequent
umounts provided that enough distinct UID's to actually make the
hash do something are active.
This can probably explain a number of weird quota related behaviours.
PR: 32331 maybe more.
Reproduced by: Søren Schrørder <sch@cybercity.dk>
traps on the first instruction of signal handlers.
In trap.c:syscall(), fake a trace trap if the single-step flag was set
on entry to the kernel, not if it will be set on exit from the kernel.
This fixes bogus trace traps after the last instruction of signal handlers.
gdb-4.18 (the version in FreeBSD) still has problems with the program in
the PR. These seem to be due to bugs in gdb and not in FreeBSD, and are
fixed in gdb-5.1 (the distribution version).
PR: 33262
Tested by: k Macy <kip_macy@yahoo.com>
MFC after: 1 day
properly translate the interface name passed to us, make sure
we also translate correctly before we return the list of
interfaces with the SIOCGIFCONF ioctl. It is common to use
the interface names returned by that ioctl in further ioctls,
such as SIOCGIFFLAGS.
Remove linux_ifname as it is no longer used. Also remove
ifname_bsd_to_linux as it cannot be used anymore now that
linux_ifname is removed (was deadcode anyway).
Reported and tested by: Andrew Atrens <atrens@nortelnetworks.com>
simplifying the module linking process and eliminating the risks
associated with doubly-defined variables.
Cases where commons were legitimately used (detection of
compiled-in subsystems) have been converted to use sysinits, and
any new code should use this or an equivalent practice as a
matter of course.
Modules can override this behaviour by substituting -fno-common
out of ${CFLAGS} in cases where commons are necessary
(eg. third-party object modules). Commons will be resolved and
allocated space when the kld is linked as part of the module
build process, so they will not pose a risk to the kernel or
other modules.
Provide a mechanism for controlling the export of symbols from
the module namespace. The EXPORT_SYMS variable may be set in the
Makefile to NO (export no symbols), a list of symbols to export,
or the name of a file containing a newline-seperated list of
symbols to be exported. Non-exported symbols are converted to
local symbols. If EXPORT_SYMS is not set, all global symbols are
currently exported. This behaviour is expected to change (to
exporting no symbols) once modules have been converted.
Reviewed by: peter (in principle)
Obtained from: green (kmod_syms.awk)
and to inherently verify its validity. Alpha signal frames and trap
frames are different; this field identifies which format the context
is
Set the machine context format (signal frame) before copying it out
when sending a signal.
Approved by: -arch
whether the machine context is valid and whether the FPU state is
valid (saved).
Mark the machine context valid before copying it out when sending a
signal.
Approved by: -arch
process of being unmounted. This allows forced NFS unmounts to
complete even if there are processes stuck holding the mnt_lock
while the server is down. The mechanism is not ideal in that there
is a small chance we might accidentally cancel requests during a
failed non-forced unmount attempt on that filesystem, but this
is not really a big problem.
Also, move the tsleep() in nfs_nmcancelreqs() so that we do not
sleep in the case where there are no requests to be cancelled.
can't acquire the mnt_lock without blocking. Normally non-forced
unmount attempts return EBUSY quickly if any vnodes are active, so
this just extends that behaviour to cover the per-mount mnt_lock
too.
libmchain.
KMODDEPS seems to be a no-op in HEAD, but is required in RELENG_4,
where MODULE_DEPEND seems to be a no-op.
Therefore, this change is harmless in -CURRENT, but will fix the
dependencies when merged to RELENG_4, where they are currently not
registered!
PR: kern/33625
Submitted by: Joe Marcus Clarke <marcus@marcuscom.com>
cpu(s) into the kernel, and sync-ing them up to "kernel" mode so we can
send them ipis, which also work.
Thanks to John Baldwin for providing me with access to the hardware
that made this possible.
Parts obtained from: bsd/os
Call critical_enter/critical_exit around (fast) interrupt handlers. All
non-threaded interrupts are fast, and the threaded interrupt scheduler is
itself a fast interrupt.
Assert that an interrupt handler we are about to call is non-zero.
Be paranoid about restoring the users global registers. Do it as the
last thing before switching to alternate globals (when we magically get
our preloaded registers back), and do it with interrupts disabled. Any
kind of kernel trap when the globals are not setup properly is bad news.
Don't save and restore the kernel g6, it invariably points to the current
pcb now.
data word in an interrupt packet is non-zero, it points to code to execute
to handle the ipi, so jump to it instead of enqueueing the packet. It
is unclear if we will need queued ipis.
Interrupt g7 now points to pcpu, instead of to the per-cpu interrupt queue
itself, so use that instead. Interrupt g6 is no longer reserved.
parameters needed for smp support.
If we are not the boot processor, jump to the smp startup code instead.
Implement a per-cpu panic stack, which is used for bootstrapping both
primary and secondary processors and during faults on the kernel stack.
Arrange the per-cpu page like the pcb, with the struct pcpu at the end
of the page and the panic stack before it.
Use the boot processor's panic stack for calling sparc64_init.
Split the code to set preloaded global registers and to map the kernel
tsb out into functions, which non-boot processors can call.
Allocate the kstack for thread0 dynamically in pmap_bootstrap, and give
it a guard page too.
to the current pcb.
Remove interrupt global defines; they use PCPU_REG now.
Move ATOMIC_INC_INT here from exception.s, add ATOMIC_DEC_INT.
Add a KASSERT macro for use in assembler.
instead of relying on the previous filters to be present.
Back out r1.125, as a reset is needed to unload any existing microcode,
(which clears the multicast addresses), as it is superceded by this change.
automatically extended to prevent overflow.
* Added sbuf_vprintf(); sbuf_printf() is now just a wrapper around
sbuf_vprintf().
* Include <stdio.h> and <string.h> when building libsbuf to silence
WARNS=4 warnings.
Reviewed by: des
macro. As a result, mandatory signal delivery policies will be
applied consistently across the kernel.
- Note that this subtly changes the protection semantics, and we should
watch out for any resulting breakage. Previously, delivery of SIGIO
in this circumstance was limited to situations where the subject was
privileged, or where one of the subject's (ruid, euid) matched one
of the object's (ruid, euid). In the new scenario, subject (ruid, euid)
are matched against the object's (ruid, svuid), and the object uid's
must be a subset of the subject uid's. Likewise, jail now affects
delivery, and special handling for P_SUGID of the object is present.
This change can always be reversed or tweaked if it proves to disrupt
application behavior substantially.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
authorized based on a subject credential rather than a subject process.
This will permit the same logic to be reused in situations where only
the credential generating the signal is available, such as in the
delivery of SIGIO.
- Because of two clauses, the automatic success against curproc,
and the session semantics for SIGCONT, not all logic can be pushed
into cr_cansignal(), but those cases should not apply for most other
consumers of cr_cansignal().
- This brings the base system inter-process authorization code more
into line with the MAC implementation.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
fifesystem problems could prevent the release from completing and
this could result in init being blocked indefinitely.
This was looked over by Matt ages ago.
Approved by: dillon
SMTX in utils such as ps and top. The KI_CTTY flag was assigned to
kinfo_proc->ki_kiflag rather than or'd into the flag, thus clobbering
any flags set earlier, including KI_MTXBLOCK.
Prodding by: peter
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
firmware to delay completion of commands so that it can attempt to batch
a bunch of completions at once- either returning 16 bit handles in mailbox
registers, or in a resposne queue entry that has a whole wad of 16 bit handles.
Distinguish between 2300 and 2312 chipsets- if only because the revisions
on the chips have different meanings.
Add more instrumentation plus ISP_GET_STATS and ISP_CLR_STATS ioctls.
Run up the maximum number of response queue entities we'll look at
per interrupt.
If we haven't set HBA role yet, always return success from isp_fc_runstate.
MFC after: 2 weeks
(There has been some discussion, whether ENOENT or EBADF is more
appropriate. I choose the latter, since the operation is not supported
on the file descriptor at that time, even if it was, immediately before.)
PR: 32681
Reviewed by: dillon, iedowse, ...
Approved by: nectar
MFC after: 3 days
(pending RE approval)
substantial fraction of the number of entries of tte's in the tsb
would need to be looked up, traverse the tsb instead. This is crucial
in some places, e.g. when swapping out a process, where a certain
pmap_remove() call would take very long time to complete without this.
2. Implement pmap_qenter_flags(), which will become used later
3. Reactivate the instruction cache flush done when mapping as executable.
This is required e.g. when executing files via NFS, but is known to
cause problems on UltraSPARC-IIe CPU's. If you have such a CPU, you
will need to comment this call out for now.
Submitted by: jake (3)
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
struct ofw_nexus_reg. Implement UPA device memory management in the
nexus driver.
Adapt the psycho driver to these changes, and do some minor cleanup work
while being there.
form L0IFPI2UNIT. This could result in a panic if the user tried to
trace using isdntrace(8). I fixed this locally but forgot to commit it.
Reminded by: "Wittig, Christoph" <wc@medianet-world.de>
down, even if there are hung processes and the mount is non-
interruptible.
This works by having nfs_unmount call a new function nfs_nmcancelreqs()
in the FORCECLOSE case. It scans the list of outstanding requests
and marks as interrupted any requests belonging to the specified
mount. Then it waits up to 30 seconds for all requests to terminate.
A few other changes are necessary to support this:
- Unconditionally set a socket timeout so that even hard mounts
are guaranteed to occasionally check the R_SOFTTERM flag on
requests. For hard mounts this flag can only be set by
nfs_nmcancelreqs().
- Reject requests on a mount that is currently being unmounted.
- Never grant the receive lock to a request that has been cancelled.
This should also avoid an old problem where a forced NFS unmount
could cause a crash; it occurred when a VOP on an unlocked vnode
(usually VOP_GETATTR) was in progress at the time of the forced
unmount.
This gives a bit of a sluggish console, but it prevents the console from
getting stuck if we poll too fast, as well as other badness on certain
machines.
2. Fix a test for != 0 that should have been > 0.
Noticed by: Jamey Wood <Jamey.Wood@Sun.COM> and myself
Submitted by: tmm (2)
for certain user pages, stores to kernel pages would not update the
affected cache lines, which would sometimes cause the wrong data to be
returned for loads from kernel pages. This was especially fatal when
the addresses affected held the kernel stack pointer, and a random
value was loaded into it.
Fix a harmless off by one error in a dcache_inval_phys call.
Fix a potential race in setting up the per-cpu pointer if the special
restore fails on return to user mode fails and we need to trap back
into the kernel to fault in more stack.
Remove debug code.
an efficient way for the kernel to bounce certain mundane traps back to
userland for handling there. A user trap handler returns directly to the
trapping user code, rather than going through the kernel again. Only a
handful of instructions are actually executed in kernel mode.
Implement sysarch(SPARC_UTRAP_INSTALL).
Add code to handle sharing of the user trap table across forks and unsharing
at exec.
This can be used to implement efficient tracking of floating point register
usage in userland, fe by a thread library, and to handle alignment fault
fixups and instruction emulation in userland, for which the code may need
to be different for 32bit and 64bit binaries.
something wrong with the kernel stack.
Add code to check the kernel stack pointer in various important places
and try hard not to go down in flames if its wrong.
- Move from msleep/wakeup to condvar.
- Return either zero or a positive errno value from a function.
Return additional result via references.
- Unify the typedef of callback functions.
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
a packed array so sizeof work. This broke RFMON mode and passing
up 802.11 packets.
The Linux emulation code was derived from the open source Linux driver to
maintain compatibility.
LEAP support is added, hints from Richard Johnson. I've verified this
locally with PC350v42510.img firmware. More bug fixing from Marco to
fix long passwords.
Change DELAYs in flash part of driver to FLASH_DELAY which uses tsleep
so it doesn't look like your system died during a flash update.
Install header files in /usr/include/dev/an
Cleanup some ifmedia bugs add "Home" key mode to ifmedia and ancontrol.
This way you can manage 2 keys a little easier. Map the home mode into
key 5. Enhance ifconfig to dump the various configured SSIDs. I use
a bunch of different ones and roam between them. Use the syntax similar
to the WEP keys to deal with setting difference SSIDs.
Bump up up the Card capabilities RID since they added 2 bytes to it
in the latest firmware. Thankfully we changed it from a terminal
failure so the card still worked but the driver whined.
Some cleanup patches from Marco Molteni.
Submitted by: Richard Johnson <raj@cisco.com>
Marco Molteni <molter@tin.it>
and myself
Various checks: David Wolfskill <david@catwhisker.org>
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Obtained from: Linux emulation API's from Aironet driver.
they were right. Fix both kenter() and kremove() for SMP by ensuring that
the tlb is flushed on other cpu's. This will directly solve random-corruption
panic issues in -stable when it is MFC'd. Better to be safe then sorry, we
can optimize this later.
Original Suspicion by: peter
Maybe MFC: immediately on re's permission
socreate(), rather than getting it implicitly from the thread
argument.
o Make NFS cache the credential provided at mount-time, and use
the cached credential (nfsmount->nm_cred) when making calls to
socreate() on initially connecting, or reconnecting the socket.
This fixes bugs involving NFS over TCP and ipfw uid/gid rules, as well
as bugs involving NFS and mandatory access control implementations.
Reviewed by: freebsd-arch
must have been inadvertently changed to '>'. This broke nfsm_adv()
in the case where the advancement count is equal to the amount of
data remaining in the current mbuf. Instead of moving the current
position N bytes forward, nfs_adv() could end up moving it back to
N bytes from the start of the mbuf data.
This should fix the client-side readdirplus problems that have been
reported since September.
In order of importance:
* Make ugen use updated frlengths.
* More tests for NULL pipes.
* Generate better error codes on bulk write.
* Error messages in general.
IPv6 on an sppp interface. In an IPv6-enabled kernel, every IPv6
interface automatically gets an IPv6 address assigned (and IPv6
multicast packets sent at initialization time). For sppp links where
we know our remote peer wouldn't support IPv6 at all, there's no point
in attempting to negotiate IPV6CP (or to even dial out for an IPv6
packet at all for dial-on-demand interfaces).
I wish there were a more generic way to administratively disable IPv6
on an interface instead. ume told me there isn't.
While i was at it, converted both, enable_vj and enable_ipv6 into flag
bits in struct sppp (enable_vj used to be an int of its own).
MFC after: 1 month
