prime objectives are:
o Implement a syscall path based on the epc inststruction (see
sys/ia64/ia64/syscall.s).
o Revisit the places were we need to save and restore registers
and define those contexts in terms of the register sets (see
sys/ia64/include/_regset.h).
Secundairy objectives:
o Remove the requirement to use contigmalloc for kernel stacks.
o Better handling of the high FP registers for SMP systems.
o Switch to the new cpu_switch() and cpu_throw() semantics.
o Add a good unwinder to reconstruct contexts for the rare
cases we need to (see sys/contrib/ia64/libuwx)
Many files are affected by this change. Functionally it boils
down to:
o The EPC syscall doesn't preserve registers it does not need
to preserve and places the arguments differently on the stack.
This affects libc and truss.
o The address of the kernel page directory (kptdir) had to
be unstaticized for use by the nested TLB fault handler.
The name has been changed to ia64_kptdir to avoid conflicts.
The renaming affects libkvm.
o The trapframe only contains the special registers and the
scratch registers. For syscalls using the EPC syscall path
no scratch registers are saved. This affects all places where
the trapframe is accessed. Most notably the unaligned access
handler, the signal delivery code and the debugger.
o Context switching only partly saves the special registers
and the preserved registers. This affects cpu_switch() and
triggered the move to the new semantics, which additionally
affects cpu_throw().
o The high FP registers are either in the PCB or on some
CPU. context switching for them is done lazily. This affects
trap().
o The mcontext has room for all registers, but not all of them
have to be defined in all cases. This mostly affects signal
delivery code now. The *context syscalls are as of yet still
unimplemented.
Many details went into the removal of the requirement to use
contigmalloc for kernel stacks. The details are mostly CPU
specific and limited to exception_save() and exception_restore().
The few places where we create, destroy or switch stacks were
mostly simplified by not having to construct physical addresses
and additionally saving the virtual addresses for later use.
Besides more efficient context saving and restoring, which of
course yields a noticable speedup, this also fixes the dreaded
SMP bootup problem as a side-effect. The details of which are
still not fully understood.
This change includes all the necessary backward compatibility
code to have it handle older userland binaries that use the
break instruction for syscalls. Support for break-based syscalls
has been pessimized in favor of a clean implementation. Due to
the overall better performance of the kernel, this will still
be notived as an improvement if it's noticed at all.
Approved by: re@ (jhb)
ia64 only uses relocations with addend, remove the sections specific to
non-addend relocations (.rel.*). Also remove C++ specific sections.
Approved by: re@ (blanket)
stolen from the ia64/ia32 code (indeed there was a repocopy), but I've
redone the MD parts and added and fixed a few essential syscalls. It
is sufficient to run i386 binaries like /bin/ls, /usr/bin/id (dynamic)
and p4. The ia64 code has not implemented signal delivery, so I had
to do that.
Before you say it, yes, this does need to go in a common place. But
we're in a freeze at the moment and I didn't want to risk breaking ia64.
I will sort this out after the freeze so that the common code is in a
common place.
On the AMD64 side, this required adding segment selector context switch
support and some other support infrastructure. The %fs/%gs etc code
is hairy because loading %gs will clobber the kernel's current MSR_GSBASE
setting. The segment selectors are not used by the kernel, so they're only
changed at context switch time or when changing modes. This still needs
to be optimized.
Approved by: re (amd64/* blanket)
of the infrastructure for the gamma driver which was removed a while back.
The DRM_LINUX option is removed because the handler is now provided by the
linux compat code itself.
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
to force the allocation of MAC labels for all mbufs regardless of
whether a configured policy requires labeling when the mbuf is
allocated. This can be useful it you anticipate loading a fully
labeled policy after boot and don't want mbufs to exist without
label storage, for performance measurement purposes, etc. It also
slightly lowers the overhead of m_tag labeling due to removing the
decision logic.
While here, improve commenting of other MAC options.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
kernel opition 'options PAE'. This will only work with device drivers which
either use busdma, or are able to handle 64 bit physical addresses.
Thanks to Lanny Baron from FreeBSD Systems for the loan of a test machine
with 6 gigs of ram.
Sponsored by: DARPA, Network Associates Laboratories, FreeBSD Systems
