Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The ACPI global lock acquire takes a timeout value. I'm not sure what
we should do about timeouts on it; a deadlock against this lock is
catastrophic.
- Temporary fix a bug of Intel ACPI CA core code.
- Add OS layer ACPI mutex support. This can be disabled by
specifying option ACPI_NO_SEMAPHORES.
- Add ACPI threading support. Now that we have a dedicate taskqueue for
ACPI tasks and more ACPI task threads can be created by specifying option
ACPI_MAX_THREADS.
- Change acpi_EvaluateIntoBuffer() behavior slightly to reuse given
caller's buffer unless AE_BUFFER_OVERFLOW occurs. Also CM battery's
evaluations were changed to use acpi_EvaluateIntoBuffer().
- Add new utility function acpi_ConvertBufferToInteger().
- Add simple locking for CM battery and temperature updating.
- Fix a minor problem on EC locking.
- Make the thermal zone polling rate to be changeable.
- Change minor things on AcpiOsSignal(); in ACPI_SIGNAL_FATAL case,
entering Debugger is easier to investigate the problem rather than panic.
disabled unless verbose flag is set. Also fix some messages in terms
of English.
The critical messages and error messages in probe/attach routine are
unchanged by this commit.
Fix acpi_DeviceIsPresent to check for valid _STA data and to check
the "present" and "functioning" bits.
Use acpi_DeviceIsPresent in acpi_pcib rather than rolling our own
(also broken) version.
- Use __func__ instead of __FUNCTION.
- Support power-off to S3 or S5 (takawata)
- Enable ACPI debugging earlier (with a sysinit)
- Fix a deadlock in the EC code (takawata)
- Improve arithmetic and reduce the risk of spurious wakeup in
AcpiOsSleep.
- Add AcpiOsGetThreadId.
- Simplify mutex code (still disabled).
handle read and write requests for widths of multiple bytes. This
can be used to read 16-bit battery status registers for example.
- Remove some unused variables and #if 0'd debugging cruft.
- Don't complain about a GPE query that fails due to AE_NOT_FOUND if the
query method was _Q00.
Use acpi_EvaluateInteger where possible.
Use FuncName rather than &FuncName when passing function addresses.
Don't evaluate the _REG method when we attach to an address space -
AcpiInstallAddressSpaceHandler does it for us.
infrastructure. It's not perfect, but it's a lot better than what
we've been using so far. The following rules apply to this:
o BSD component names should be capitalised
o Layer names should be taken from the non-CA set for now. We
may elect to add some new BSD-specific layers later.
- Make it possible to turn off selective debugging flags or layers
by listing them in debug.acpi.layer or debug.acpi.level prefixed
with !.
- Fully implement support for avoiding nodes in the ACPI namespace.
Nodes may be listed in the debug.acpi.avoid environment variable;
these nodes and all their children will be ignored (although still
scanned over) by ACPI functions which scan the namespace. Multiple
nodes can be specified, separated by whitespace.
- Implement support for selectively disabling ACPI subsystem components
via the debug.acpi.disable environment variable. The following
components can be disabled:
o bus creation/scanning of the ACPI 'bus'
o children attachment of children to the ACPI 'bus'
o button the acpi_button control-method button driver
o ec the acpi_ec embedded-controller driver
o isa acpi replacement of PnP BIOS for ISA device discovery
o lid the control-method lid switch driver
o pci pci root-bus discovery
o processor CPU power/speed management
o thermal system temperature detection and control
o timer ACPI timecounter
Multiple components may be disabled by specifying their name(s)
separated by whitespace.
- Add support for ioctl registration. ACPI subsystem components may
register ioctl handlers with the /dev/acpi generic ioctl handler,
allowing us to avoid the need for a multitude of /dev/acpi* control
devices, etc.
- Use ACPI_PHYSICAL_ADDRESS
- RSDT -> XSDT
- FACP -> FADT
- No APIC table support
- Don't install a global EC handler; this has bad side-effects
(it invokes _REG in *all* EC spaces in the namespace!)
- Check for PCI bus instances already existing before adding them
ACPICA. Most of these are still works in progress. Support exists for:
- Fixed feature and control method power, lid and sleep buttons.
- Detection of ISA PnP devices using ACPI namespace.
- Detection of PCI root busses using ACPI namespace.
- CPU throttling and sleep states (incomplete)
- Thermal monitoring and cooling control (incomplete)
- Interface to platform embedded controllers (mostly complete)
- ACPI timer (incomplete)
- Simple userland control of sleep states.
- Shutdown and poweroff.
