This is Infineon ADM6996FC/M/MX driver code on etherswitch framework.
Support PORT and DOT1Q VLAN.
This code suppose ADM6996FC SDC/SDIO connect to SOC network interface
MDC/MDIO.
This code tested on Netgear WGR614Cv7.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: adrian, mizhka
Approved by: adrian(mentor)
Differential Revision: https://reviews.freebsd.org/D8495
The feature enables us to pass through physical PCIe devices to FreeBSD VM
running on Hyper-V (Windows Server 2016) to get near-native performance with
low CPU utilization.
The patch implements a PCI bridge driver to support the feature:
1) The pcib driver talks to the host to discover device(s) and presents
the device(s) to FreeBSD's pci driver via PCI configuration space (note:
to access the configuration space, we don't use the standard I/O port
0xCF8/CFC method; instead, we use an MMIO-based method supplied by Hyper-V,
which is very similar to the 0xCF8/CFC method).
2) The pcib driver allocates resources for the device(s) and initialize
the related BARs, when the device driver's attach method is invoked;
3) The pcib driver talks to the host to create MSI/MSI-X interrupt
remapping between the guest and the host;
4) The pcib driver supports device hot add/remove.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8332
The new methods will be used by the coming pcib driver.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8409
vcpu_id is host's representation of guest CPU.
We get the mapping between vcpu_id and FreeBSD kernel's cpu id when VMBus
driver is loaded. Later, when a driver, like the coming pcib driver, talks
to the host and needs to refer to a guest CPU, the driver must use the
vcpu_id.
Reviewed by: jhb, sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8410
Drop the tracking down to the pmap layer, with optimizations to only track
necessary pages. This should give a (slight) performance improvement, as well
as a stability improvement, as the tracking is already mostly handled by the
pmap layer.
Summary:
This implements part of the gpio-poweroff and gpio-restart device tree
bindings. Optional properties are not handled currently. It also currently
only supports level-triggered reset.
Reviewed By: gonzo
Differential Revision: https://reviews.freebsd.org/D8521
If MII1 interface is disabled, then enable phy4/mac4.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka, adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6832
This commit is part of D6920 review. One of macro had wrong prefix:
BMCA => BCMA
Reviewed by: landonf, adrian (mentor)
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6920
To enable event sourcing from kbdmux(4) kern.evdev.rcpt_mask value
should have bit 1 set (this is default)
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8437
VSS stands for "Volume Shadow Copy Service". Unlike virtual machine
snapshot, it only takes snapshot for the virtual disks, so both
filesystem and applications have to aware of it, and cooperate the
whole VSS process.
This driver exposes two device files to the userland:
/dev/hv_fsvss_dev
Normally userland programs should _not_ mess with this device file.
It is currently used by the hv_vss_daemon(8), which freezes and
thaws the filesystem. NOTE: currently only UFS is supported, if
the system mounts _any_ other filesystems, the hv_vss_daemon(8)
will veto the VSS process.
If hv_vss_daemon(8) was disabled, then this device file must be
opened, and proper ioctls must be issued to keep the VSS working.
/dev/hv_appvss_dev
Userland application can opened this device file to receive the
VSS freeze notification, hold the VSS for a while (mainly to flush
application data to filesystem), release the VSS process, and
receive the VSS thaw notification i.e. applications can run again.
The VSS will still work, even if this device file is not opened.
However, only filesystem consistency is promised, if this device
file is not opened or is not operated properly.
hv_vss_daemon(8) is started by devd(8) by default. It can be disabled
by editting /etc/devd/hyperv.conf.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reviewed by: kib, mckusick
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8224
Do not overwrite the contents of the WUC register, add E1000_WUC_PME_EN
to the register contents, leaving the default contents intact.
PR: 208343
Submitted by: Kaho Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>
Reviewed by: jeffrey piper <jeffrey.e.pieper@intel.com>
Approved by: erj@
MFC after: 2 weeks
Linux has a slightly different device tree definition for DPAA than originally
done in the FreeBSD driver. This changes the driver to be mostly compatible
with the Linux device tree definitions. Currently the differences are:
bman-portals: compatible = "fsl,bman-portals" (Linux is "simple-bus")
qman-portals: compatible = "fsl,qman-portals" (Linux is "simple-bus")
fman: compatible = "fsl,fman" (Linux is "simple-bus")
The Linux device tree doesn't specify anything for rgmii in the mdio. This
change still requires the device tree to specify the phy-handle, and doesn't yet
support tbi.
before calling ieee80211_ifattach() so the taskqueue hasn't been
initialized. Don't try to drain it, we'll panic.
Looks like this issue was introduced in r303326.
Reviewed by: avos, sbruno, adrian
Differential Revision: https://reviews.freebsd.org/D8499
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
- Attach only to WMI devices that provide supported GUIDs. HP Spectre x360
has two WMI devices, only one of which provides the GUIDs.
- Pass proper device to ACPI_WMI_REMOVE_EVENT_HANDLER() on detach.
- Improve error WMI handling separating status and data paths. This allows
to hide sysctls not supported by specific hardware/BIOS.
- Improve CMI block parser to make it work on HP Spectre x360 laptop.
- In verbose mode log all unknown events to help futher improvements.
In the case where a hardware error is detected during
ioat_process_events, hardware may advance (by one descriptor, probably)
and a subsequent ioat_process_events may race the intended ioat_reset_hw
followup. In that case, the second process_events would observe a
completion update that does not match the software "last_seen" status,
and attempt to successfully complete already-failed descriptors.
Guard against this race with the resetting_cleanup flag.
Reviewed by: bdrewery, markj
Sponsored by: Dell EMC Isilon
Newer CPUs (SkyLakes) have updates of 100K size, which is bigger than
current limit 32K. Increase it to 4M but leave the check around to
prevent kernel memory allocator abuse. Some time ago, the memory for
update was allocated by contigmalloc(9), and it was reasonable to be
conservative as much as possible. Since all uses of contigmalloc(9)
appear to be either misunderstanding or too cautious, and were
removed, provide more slack than strictly neccessary.
Submitted by: Oliver Pinter
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D8486
The constant was set to the correct value in r308242.
While there, fix iicsmb_bread() to not use a value of an out parameter
'count'.
MFC after: 3 weeks
X-MFC after: r308242
The hardware does not implement SMBus Process Call command, so remove
ifdef-ed out code from intsmb_pcall. The code used exactly the same
start sequence as for Write Word command.
intsmb_bread code used to access an in value of the count parameter,
but that parameter is supposed to be an out only parameter.
For example, smb(4) does not initialize it before calling smbus_bread.
MFC after: 3 weeks
Previously, those ioctls were defined as 'in' only, so rdata.byte and
rdata.word were never updated in the userland. The read data went only
to rbuf if it was provided. Thus, consumers were forced to always use it.
Now the ioctls are marked as in-out.
Compatibility handlers are provided for old ioctls.
PR: 213481
Reported by: Lewis Donzis <lew@perftech.com>
MFC after: 2 weeks
Relnotes: maybe
Differential Revision: https://reviews.freebsd.org/D8430
I see the fllowing panic on AMD when exiting pmcstat:
panic: [pmc,1473] pp_pmcval outside of expected range cpu=2 ri=17
pp_pmcval=fffffffffa529f5b pm_reloadcount=10000
It seems that at least on AMD a performance counter keeps counting after
overflowing. When pmcstat exits it sets counters that it used to
PMC_STATE_DELETED and waits until their use count goes to zero.
amd_intr() wouldn't reload a counter in that state and, thus, a counter
would be allowed to overflow. That means that the counter's value would
be allowed to go outside the expected range.
MFC after: 2 weeks
The expected deviation should not be more than 1Hz per second. The USB
v2.0 specification also mandates this requirement. Refer to chapter
5.12.4.2 about feedback.
PR: 208791
MFC after: 3 days
address, but the associated PF is giving the VF an all zeros MAC address
when one is not administratively assigned. The driver should check for
this case and generate a random address, similar to how the linux igbvf
driver does.
Submitted by: skoumjian@juniper.net (Scott Koumjian)
MFH: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8399
- Split driver in two parts: FDT and non-FDT
- Instead of reattach gpioled nodes to GPIO bus use
gpio_pin_get_by_ofw_idx and add ofwbus and simplebus as parrent buses
Reviewed by: loos
Differential Revision: https://reviews.freebsd.org/D8233
The firmware/hardware does not generate additional completion
events unless we post new buffers. Use a timer to try to post
more buffers in case we are temporarily out of mbufs. Else
the receive schedule completely stops.
Sponsored by: Mellanox Technologies
MFC after: 1 week
