Install the biosboot as /usr/mdec/boot[12]
Make the traditional links from [swf]dboot and boot[swf]d to boot[12] files.
Install dosboot as /usr/mdec/boot/fbsdboot.exe
1) Preserve old buffer contents when input buffer overflows.
Old code clear buffer and rewrite it again, if !MAXBEL
(for MAXBEL it does right thing :-).
F.e. if you type too long string, last chars passed,
not first ones as expected.
Moreover, it flush output queue too in this case without any needs.
2) Don't do IXOFF, if IGNCR and c==\r, ignore completely.
3) If PARMRK is active and !ISTRIP and char == 0377
put yet one 0377 to distinguish it from parity mark sequence.
POSIX standard (thanx Bruce).
Reviewed by:
Submitted by:
Obtained from:
CVS:
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
merged cache changes, and figure it out based on the B_VMIO buffer flag.
Fixes a problem where delayed write VMIO buffers would sometimes get
recopied into kernel-alloced memory.
Submitted by: John Dyson
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
- ignore the partition table if it is identical with the bogus one in
/usr/src/sys/i386/boot/biosboot/start.S. Honoring the bogus size
field was fatal. The error is detected but other compatibilty
cruft weakens the error handling too much for this case.
- weaken the partition entry checking to allow the following treatments
of C/H/S addresses when C should be >= 1024:
(1) allow C = 1023, H = max, S = max.
(2) allow C to be correct modulo 1024.
Other compatibilty cruft weakens the error handling to allow all
C/H/S addresses, but there too many errors were reported.
Improve error messages:
- print C/H/S addresses if relevant.
- distinguish primary partition table from extended partition tables.
- don't use diskerr() except for i/o errors.
to accurately track this. It isn't an indicator of resource consumption
anyway.
Removed cnt.v_kernel_pages: We don't implement this and doing so accurately
would be very difficult (and ambiguous - since process pages are often
double mapped in the kernel and the process address spaces).
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
in.c: when an interface address is deleted, keep its multicast membership
. records (attached to a struct multi_kludge) for attachment to the
. next address on the same interface. Also, in_multi structures now
. gain a reference to the ifaddr so that they won't point off into
. freed memory if an interface goes away and doesn't come back before
. the last socket reference drops. This is analogous to how it is
. done for routes, and seems to make the most sense.
function calls. Broken tracking of open partitions gets fixed as a side
effect. Races in sdopen() and sdioctl() become more numerous than before.
Close the device in sdsize(). Media removal could not have worked right
when unused swap devices were held open. There may now be a problem
with used swap devices not being held open.
Fix ancient operator precedence bug in sddump(). It may have been
possible to attempt dumping to unloaded media.
Remove NetBSD ifdefs. We're too different now, and the NetBSD driver was
already too different for them to be relevant.
Remove support for soft write protection. There are no ioctls to set it,
and this driver never set it either. It was used in the wd driver to
disable writing to unlabelled disk, but we want to support writing to
foreign partitions on unlabeled disks.
Clean up some formatting and restore some old-style function headers.
happen normally when there is heavy write activity to a file since the
vnode isn't locked (NFS plays fast and loose with vnode locks). This change
"fixes" PR#267.
ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
VTEXT not always getting cleared when it is supposed to. Added check to
make sure that vm_object_remove() isn't called with a NULL pager or for
a pager for an OBJ_INTERNAL object (neither of which will be on the hash
list). Clear OBJ_CANPERSIST if we decide to terminate it because of no
resident pages.
Fixed the I/O statistics
Allow WD1007 type controllers to work
Support MULTI-BLOCK I/O
Correct delay to use port 0x84, reading the status register
might not be a long enough delay.
Changed probe message to match SCSI type devices.
was the wrong size. This is the likely cause of panics reported by
Lars Fredriksen and Paul Richards related to a -1 blkno when paging
via the swap_pager.
Submitted by: John Dyson
1) Supports PCI to PCI bridge devices (and tries to initialise them,
even if the BIOS is brain dead).
2) Supports shared PCI interrupts. Interrupt handlers now MUST return
'0' if they found nothing to do, '1' otherwise.
New features tested with i486 systems based on the Intel Saturn and
a DEC 4channel Ethernet card only, but expected to work on most systems.
The option PCI_REMAP has been removed !
Submitted by: Wolfgang Stanglmeier <wolf@kintaro.cologne.de>
sd.c: Julian's removal of subdriver requests
st.c, scsi_tape.h: Julian's suport of compressed tape drives
Note: compressed tape drives are still not working fully.
scsiconf.h, scsi_base.c, scsi_driver.c: address problems in probes
and error console logs
to the user address space unless pcb_onfault is set. The code is currently
commented out because iBCS2 and process debugging parts of the kernel
need to be changed/fixed first.
fix Dennis Fortin's problem for good, if I've got it figured out right.
(The problem was that a `struct ifaddr' could get deleted out from under
the current requester, thus leaving him with an invalid interface pointer
and causing even more bogus accesses.)
routines (and merged local changes). The changed vnode_pager_uncache
gets rids of the bogosity that you can call the routine without
having the vnode locked. The changed vnode_pager_umount properly locks
the vnode before calling vnode_pager_uncache.
It was previously after the VOP_RENAME and the reference and lock on
the vnode had already been lost, allowing interesting internel
inconsistencies. This is one of the two reasons why freefall was crashing
every hour or two (the other being nullfs bugs).
Don't call vnode_pager_uncache in revoke(). revoke() is only allowed on
VCHR and VBLK vnodes.
during the FS sync. The system would appear to hang momentarily
if there was a large backlog of I/O. This is because the vnode
remains locked during the output - preventing normal character
I/O. The problem was exacerbated by the FFS contiguous block
allocation fixes and a semi-broken disksort(). The inode/date
will still be synced during a normal FS dismount and whenever
the inode is changed for other reasons.
probe of the device and shouldn't affect normal operation. It seems that
some version of the aic7870 are extreamly slow in clearing their interrupt
register so the added delay is required to ensure we don't poll a stale
interrupt value.
Clean up debugging printfs and stuff superflous output into #ifdef AHC_DEBUG.
Ensure that sdtrpending and wdtrpending are cleared in all cases after
we recieve an SDTR or WDTR message.
With this commit, the 294x should work or at least be much closer to
working properly.
a device specific shutdown routine for devconf. Assign the value of this
to the kern_devconf struct. Implement a device shutdown routine for if_de
that disables the device. This will stop the device from corrupting memory
after a reboot.
VFCF_NETWORK (this FS goes over the net)
VFCF_READONLY (read-write mounts do not make any sense)
VFCF_SYNTHETIC (data in this FS is not real)
VFCF_LOOPBACK (this FS aliases something else)
cd9660 is readonly; nullfs, umapfs, and union are loopback; NFS is netowkr;
procfs, kernfs, and fdesc are synthetic.
submitting them as context diffs for the following files:
sys/netinet/ip_mroute.c
sys/netinet/ip_var.h
sys/netinet/raw_ip.c
usr.sbin/mrouted/igmp.c
usr.sbin/mrouted/prune.c
The routine rip_ip_input in raw_ip.c is suggested by Mark Tinguely
(tinguely@plains.nodak.edu). I have been running mrouted with these patches
for over a week and nothing has seemed seriously wrong. It is being run in
two places on our network as a tunnel on one and a subnet querier on the
other. The only problem I have run into is that mrouted on the tunnel must
start up last or the pruning isn't done correctly and multicast packets
flood your subnets.
Submitted by: Soochon Radee <slr@mitre.org>
