ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
This is a seriously beefed up chroot kind of thing. The process
is jailed along the same lines as a chroot does it, but with
additional tough restrictions imposed on what the superuser can do.
For all I know, it is safe to hand over the root bit inside a
prison to the customer living in that prison, this is what
it was developed for in fact: "real virtual servers".
Each prison has an ip number associated with it, which all IP
communications will be coerced to use and each prison has its own
hostname.
Needless to say, you need more RAM this way, but the advantage is
that each customer can run their own particular version of apache
and not stomp on the toes of their neighbors.
It generally does what one would expect, but setting up a jail
still takes a little knowledge.
A few notes:
I have no scripts for setting up a jail, don't ask me for them.
The IP number should be an alias on one of the interfaces.
mount a /proc in each jail, it will make ps more useable.
/proc/<pid>/status tells the hostname of the prison for
jailed processes.
Quotas are only sensible if you have a mountpoint per prison.
There are no privisions for stopping resource-hogging.
Some "#ifdef INET" and similar may be missing (send patches!)
If somebody wants to take it from here and develop it into
more of a "virtual machine" they should be most welcome!
Tools, comments, patches & documentation most welcome.
Have fun...
Sponsored by: http://www.rndassociates.com/
Run for almost a year by: http://www.servetheweb.com/
transceiver. Note in the manual page that autoselection doesn't
work on the 82c168 because the built-in NWAY support is horribly
broken. Manual mode selection works fine, but autoneg is broken for
everything except maybe 10Mbps half-duplex. There's no simple way
to fix this at the moment, so I have to settle for documenting the
bug for now. Fortunately, there aren't anywhere near as many 82c168
boards around as there are 82c169s.
I changed to "Christopher G. Demetriou" since the page appears to be a
revision of lkm(4).
PR: docs/8611
Submitted by: Rajesh Vaidheeswarran <rv@fore.com>
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
kernel and userland modules.
Describe the superdevice method of ensuring that people at least
recognize the problem if they run into a debug synchronization problem.
Describe /dev/vinum/control*
Describe drive "referenced" state.
Remove warning about kldunload; it seems to work now.
Still more descriptions of how to debug things.
AX88140A with power management and magic packet support. Correct the
addresses of the PCI power management registers and add some code to
detect the revision ID of the AX88141 and identify it in the probe
messages.
No other changes are needed since the AX88141 is functionally
identical to the AX88140A.
- Add syscons.4.
If there still are errors, whether technical or grammatical, they are
entirely mine, not the reviewers'.
Reviewed by: sos, jkh, archie, Nick Hilliard <nick@iol.ie>
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
and Racore 8148 adapters are now supported by the ThunderLAN driver.
The 8165 is just a plain vanilla 10/100 card; the 8148 is a 'multi-
personality' adapter which can support 10baseT, 100baseTX and 100baseFX
if you include the proper modules.
Also update the tl man page to mention the Racore cards.
+ ECP parallel port chipset FIFO detection
+ DMA+FIFO parallel I/O handled as chipset specific
+ nlpt updated in order to use the above enhanced parallel I/O.
Use 'lptcontrol -e' to use enhanced I/O
+ Various options documented in LINT
+ Full IEEE1284 NIBBLE and BYTE modes support. See ppbus(4) for
an overview of the IEEE1284 standard
+ Detection of PnP parallel devices at boot
+ Read capability added to nlpt driver to get IEEE1284 compliant
printer status with a simple 'cat /dev/lpt0'
+ IEEE1284 peripheral emulation added to BYTE mode. Two computers
may dialog according to IEEE1284 signaling method.
See PERIPH_1284 option and /sys/dev/ppbus/ppi.c
All this code is supposed to provide basic functions for IEEE1284 programming.
ppi.c and nlpt.c may act as examples.
on the ASIX AX88140A chip. Update /sys/conf/files, RELNOTES.TXT,
/sys/i388/i386/userconfig.c, sysinstall/devices.c, GENERIC and LINT
accordingly.
For now, the only board that I know of that uses this chip is the
Alfa Inc. GFC2204. (Its predecessor, the GFC2202, was a DEC tulip card.)
Thanks again to Ulf for obtaining the board for me. If anyone runs
across another, please feel free to update the man page and/or the
release notes. (The same applies for the other drivers.)
FreeBSD should now have support for all of the DEC tulip workalike
chipsets currently on the market (Macronix, Lite-On, Winbond, ASIX).
And unless I'm mistaken, it should also have support for all PCI fast
ethernet chipsets in general (except maybe the SMC FEAST chip, which
nobody seems to ever use, including SMC). Now if only we could convince
3Com, Intel or whoever to cough up some documentation for gigabit
ethernet hardware.
Also updated RELNOTEX.TXT to mention that the SVEC PN102TX is supported
by the Macronix driver (assuming you actually have an SVEC PN102TX with
a Macronix chip on it; I tried to order a PN102TX once and got a box
labeled 'Hawking Technology PN102TX' that had a VIA Rhine board inside
it).
-add "depends" to list of recursive targets
-consistent capitilization of FreeBSD.ORG
-remove description of PATCH_DEBUG
-add .Xr to portcheckout(1) and pib(1)
- Get the (tm) signal correct in nroff versions
- Correct highlighting (docs/9196)
Sigh. This is still a long way from being correct. In particular,
the states are both incorrect, and they don't format properly in
troff. But it will have to wait until I stop changing the meanings of
the states.
hacker -> intruder (couldn't desired between this and 'cracker')
config -> configuration
sorted crossreferences
spell checked
Overall very good content, but we need one of our wordsmiths to change the
tone to match the CSRG manpages.
ethernet driver.
The BUGS section is still impressive, but the driver seems to work for
me now. Disclaimer: i haven't been able to test this under -current
so far (but it compiles, and the notebook it's intended for can now be
updated to -current more easy than before). Don't be afraid of the
many #ifdefs on __FreeBSD_version in the imported file; i want them in
the repository on the vendor-branch so other people can also manually
integrate it into older systems. I'll clean it up on the -current
branch in a followup commit. The vendor-banch version right now
supports systems back to 2.2R.
This driver should be layered upon ppc(4), but i currently have no
idea how to do this.
Eventually i'll further develop the driver to also support the more
modern RTL 8012 success, which seems to be present in a number of
cheap pocket ethernet adapters these days. Right now, i doubt it will
run with the 8012 without any changes.
Finally a big Thanks! to RealTek for promptly providing me with
documentation and with the source code for the 8012 pocket driver upon
request. I wish all vendors were that cooperative!.
mechanisms. It is a little light on detail but still a pretty good
overview. I suggest that for specific detail (such as, for example,
how to setup kerberos), that additional security-DETAILNAME man pages
be written and refered to.
as a RealTek 8139
if_rlreg.h: use bus_space_read_X() in CSR_READ_X() macros instead of
directly calling inb()/outb() etc...
rl.4 + RELNOTES.TXT: mention that SMC EtherEZ PCI 1211-TX is supported
by the RealTek driver
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
configured in drivers.
Quote the last few args to form 1 arg. Quoting them in pairs almost
defeated the point of quoting them, which is to reduce the arg count
to <= 9.
SCSI controllers, respectively.
Once these drivers are tested on the alpha, these man pages can probably be
moved up a directory to reflect the fact that they're architecture
independent.
An mdoc guru should probably look at the AUTHORS sections in both of these
pages -- the .An macro seems to cause strange spacing problems.
Reviewed by: ken
Submitted by: gibbs
as cam(4) as well.
This includes a description of all the generic CAM kernel options, as
well as a description of some of the CAM debugging printf options.
st(4) man page.
Take out most of the sd(4) and st(4) man pages and point to the new
da(4) and sa(4) man pages.
Add sa.4 to the makefile.
Reviewed by: ken
Submitted by: gibbs
driver, and point users in the right direction for similar functionality.
The functionality that used to be provided there is now provided by the
cd(4) driver and cdrecord.
Fix cross-references in a few other man pages. (i.e. delete references to
things I haven't written yet)
update of the quirk entry descriptions to reflect the current state of
things.
Once I find out where such things belong, I'll document things like
the changer scheduling mechanism, actions taken at probe, etc.
This includes a description of the changer timeout kernel options and
sysctl variables. I didn't check to make sure the ioctl descriptions are
up to date; that will come sometime later. (The ioctls haven't changed in
the CAM driver, but I'm not sure if the man page was in sync with even the
old driver.)
though I'm afraid there's a lot more that needs fixing in this file,
judging by 'find /usr/src -name "*.8" -print'.
Spotted-by: glimpse -H /usr/src tickadj
Disable building tickadj(8) by removing util from SUBDIR in the xntpd
Makefile. Note that the sources are still there and tickadj can still
be built and installed by doing:
# cd /usr/src/usr.sbin/xntpd/util
# make all install
There are enough references to tickadj in e.g. the xntpd documentation
(not to mention the sysctl variables it uses etc.) that I don't feel
up to implementing the final solution right now.
Kinda-approved-by: phk
