One common method of EOI'ing an interrupt at the IO-APIC level is to
switch the pin to edge triggering mode and then back into level mode.
That would cause the IRR bit to be cleared and thus further interrupts
to be injected. FreeBSD does indeed use that method if the IO-APIC EOI
register is not supported.
The bhyve IO-APIC emulation code didn't clear the IRR bit when doing
that switch, and was also missing acknowledging the IRR state when
trying to inject an interrupt in vioapic_send_intr.
Reviewed by: grehan
Differential revision: https://reviews.freebsd.org/D28238
After modifying a redirection entry only try to inject an interrupt if
the pin is in level mode, pins in edge mode shouldn't take into
account the line assert status as they are triggered by edge changes,
not the line status itself.
Reviewed by: grehan
Differential revision: https://reviews.freebsd.org/D28237
vioapic_send_intr does already check whether the pin is masked before
injecting the interrupt, there's no need to do it in vioapic_write
also.
No functional change intended.
Reviewed by: grehan
Differential revision: https://reviews.freebsd.org/D28236
This is a tradeoff which saves jumps for smaller sizes while making
the 8-16 range slower (roughly in line with the other cases).
Tested with glibc test suite.
For example size 3 (most common with vfs namecache) (ops/s):
before: 407086026
after: 461391995
The regressed range of 8-16 (with 8 as example):
before: 540850489
after: 461671032
All page zeroing is using temporal stores with rep movs*, the routine is
unused for several years.
Should a need arise for zeroing using non-temporal stores, a more
optimized variant can be implemented with a more descriptive name.
The ptrace(2) Linux man page claims the syscall returns ESRCH,
if the tracee is not stopped; the native ptrace(2) returns EBUSY.
Sponsored by: The FreeBSD Foundation
Based on discussions on freebsd-arch@, enable KERN_TLS in
GENERIC on amd64, but leave it disabled via the
sysctl kern.ipc.tls.enable. Users wishing to enable
ktls must set kern.ipc.tls.enable=1
While here, fix wording in NOTES to mention that KERN_TLS
also does receive now.
Sponsored by: Netflix
Reviewed by: allanjude
Differential Revision: https://reviews.freebsd.org/D28163
usbhid(4) is disabled by default to avoid conflicts with existing USB HID
drivers. To enable it place following lines to /boot/loader.conf:
hw.usb.usbhid.enable=1
usbhid_load="YES"
Suggested by: jhb
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D28124
This is the superset of the nooptions found in the -DEBUG kernels.
Reviewed by: emaste, manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D28152
In particular, using GELI on a root filesystem will only use
accelerated software crypto drivers if they are available before the
root filesystem is mounted. While these modules can be loaded from
the loader, including them in GENERIC provides a better out-of-the-box
experience for users.
Both aesni(4) and armv8crypto(4) provide accelerated implementations
of the default cipher used by GELI (AES-XTS) in addition to other
ciphers.
Reviewed by: mhorne, allanjude, markj
Differential Revision: https://reviews.freebsd.org/D28100
Right now the routine leaves the current CPU in the map, later tripping
on an assert when filling in the scoreboard: panic: IPI scoreboard is
zero, initiator 1 target 1
Instead pre-check if all CPUs are present in the map and remember that
outcome for later.
Fixes: 7eaea04a5b ("amd64: compare TLB shootdown target to all_cpus")
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D28111
On amd64, the pmap code passes all_cpus to
smp_targeted_tlb_shootdown() when unmapping from the
kernel pmap. This function has an optimized path to send IPIs
to all but itself, which it intends to do when the target
is all cpus. However, we need to compare the target cpu mask
with all_cpus, rather than using CPU_ISFULLSET(). Comparing with
CPU_ISFULLSET() will only work when we have MAXCPU cpus active in
the system, otherwise, we'll be sending repeated IPIs, rather than
a single IPI to all CPUs but ourself.
Fixing this should reduce the time spent in native_lapic_ipi_wait()
as we will be sending ipis in parallel, rather than one-by-one.
This is confirmed by dtrace.
Reviewed by: alc, jhb, kib, markj
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D28102
Otherwise parallel pmap_allocpte_alloc() for nearby va might also fail
allocating page table page and free the page under us. The end result is
that we could dereference unmapped pte when doing cleanup after sleep.
Instead, on allocation failure, first free everything, only then we can
drop pmap mutex and sleep safely, right before returning to caller.
Split inner non-sleepable part of the pmap_allocpte_alloc() into a new
helper pmap_allocpte_nosleep().
Reviewed by: markj
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27956
The function performs actual allocation of pte, as opposed to
pmap_allocpte() that uses existing free pte if pt page is already
there. This also moves function out of namespace similar to a language
reserved.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27956
pmap_pdpe() might return NULL, check for it.
Reviewed by: markj
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27956
Use an interface compatible with the Linux one so that the user-space
libraries already using the Linux interface can be used without much
modifications.
This allows user-space to make use of the dm_op family of hypercalls,
which are used by device models.
Sponsored by: Citrix Systems R&D
When we already have the vm page in hand, use vm_page_domain() instead
of vm_phys_domain(). The former has a trivial constant-time
implementation whereas the latter iterates over the mem_affinity array.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D28005
Remove wi(4). pccard is going away, and wi only supports PC Card
devices, though it has a minor amount of glue to also support
PCI cards. However, removing the one without removing the other
is hard, so the whole driver is being removed.
Relnotes: Yes
This change implements hid_if.m methods for HID-over-USB protocol [1].
Also, this change adds USBHID_ENABLED kernel option which changes
device_probe() priority and adds/removes PnP records to prefer usbhid
over ums, ukbd, wmt and other USB HID device drivers and vice-versa.
The module is based on uhid(4) driver. It is disabled by default for
now due to conflicts with existing USB HID drivers.
[1] https://www.usb.org/sites/default/files/hid1_11.pdf
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27893
This does an import of quirk stubs, debugging macros from USB code and
numerous usage constants used by dependent drivers.
Besides, this change renames some functions to get a better matching
with userland library and NetBSD/OpenBSD HID code. Namely:
- Old hid_report_size() renamed to hid_report_size_max()
- New hid_report_size() calculates size of given report rather than
maximum size of all reports.
- hid_get_data_unsigned() renamed to hid_get_udata()
- hid_put_data_unsigned() renamed to hid_put_udata()
Compat shim functions are provided in usbhid.h to make possible compile
of legacy code unmodified after this change.
Reviewed by: manu, hselasky
Differential revision: https://reviews.freebsd.org/D27887
It will be used by the upcoming HID-over-i2C implementation. Should be
no-op, except hid.ko module dependency is to be added to affected drivers.
Reviewed by: hselasky, manu
Differential revision: https://reviews.freebsd.org/D27867
These handlers could interrupt code which has interrupts disabled,
and if a spurious page fault occurs during exception handler run,
we get clobbered %cr2 in higher level stack.
This is mostly a speculation, but it is based on hints from good sources.
MFC after: 1 week
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27772
The existing values correspond to x86 exception vector numbers, but the
trap numbers used in the kernel do not match these 1-to-1. Prefer the
definitions from x86/trap.h, as they are what actually get passed to
kdb_trap(). This is of little consequence, as gdb_cpu_signal() only
reports the trap reason (signal number) to the gdb client.
This is limited to the subset of trap values for which kdb_trap() is
reachable.
Reviewed by: kib
Discussed with: jhb
MFC after: 1 week
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D27645
This sysctl node can generate very verbose output, so don't trigger it
for sysctl -a or sysctl vm.pmap.
Reviewed by: markj, kib
Differential Revision: https://reviews.freebsd.org/D27504
Similar to the recent patch to arm's gdb stub in r368414, allow GDB to
update the contents of most general purpose registers.
Reviewed by: cem, jhb, markj
MFC after: 2 weeks
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
NetApp PR: 44
Differential Revision: https://reviews.freebsd.org/D27642
When r362031 moved local TLB invalidation after shootdown IPI send, it
moved too much. In particular, PCID-mode clearing of the pm_gen
generation counters must occur before IPIs are send, which is in fact
described by the comment before seq_cst fence in the invalidation
functions.
Fix it by extracting pm_gen clearing into new helper
pmap_invalidate_preipi(), which is executed before a call to
smp_masked_tlb_shootdown().
Rest of the local invalidation callbacks is simplified as result, and
become very similar to the remote shootdown handlers (to be merged in
some future).
Move pin of the thread to pmap_invalidate_preipi(), and do unpin in
smp_masked_tlb_shootdown().
Reported and tested by: mjg (previous version)
Reviewed by: alc, cem (previous version), markj
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D227588
Ability to load-balance traffic over multiple path is a must-have thing for routers.
It may be used by the servers to balance outgoing traffic over multiple default gateways.
The previous implementation, RADIX_MPATH stayed in the shadow for too long.
It was not well maintained, which lead us to a vicious circle - people were using
non-contiguous mask or firewalls to achieve similar goals. As a result, some routing
daemons implementation still don't have multipath support enabled for FreeBSD.
Turning on ROUTE_MPATH by default would fix it. It will allow to reduce networking
feature gap to other operating systems. Linux and OpenBSD enabled similar support
at least 5 years ago.
ROUTE_MPATH does not consume memory unless actually used. It enables around ~1k LOC.
It does not bring any behaviour changes for userland.
Additionally, feature is (temporarily) turned off by the net.route.multipath sysctl
defaulting to 0.
Differential Revision: https://reviews.freebsd.org/D27428
The hme (Happy Meal Ethernet) driver was the onboard NIC in most
supported sparc64 platforms. A few PCI NICs do exist, but we have seen
no evidence of use on non-sparc systems.
Reviewed by: imp, emaste, bcr
Sponsored by: DARPA
In r367395 parts of machine dependent linux_dummy.c were moved to a new
machine independent file sys/compat/linux/linux_dummy.c and the existing
linux_dummy.c was renamed to linux_dummy_machdep.c.
Add linux_dummy_machdep.c to the linux module for i386.
Rename sys/amd64/linux32/linux_dummy.c for consistency.
Add the new linux_dummy.c to the linux module for i386.
Implement vt_vbefb to support Vesa Bios Extensions (VBE) framebuffer with VT.
vt_vbefb is built based on vt_efifb and is assuming similar data for
initialization, use MODINFOMD_VBE_FB to identify the structure vbe_fb
in kernel metadata.
struct vbe_fb, is populated by boot loader, and is passed to kernel via
metadata payload.
Differential Revision: https://reviews.freebsd.org/D27373
We use 4-level EPT pages, correct the upper bound.
Reviewed by: grehan
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D27402
There is no need for these to be function pointers since they are
never modified post-module load.
Rename AMD/Intel ops to be more consistent.
Submitted by: adam_fenn.io
Reviewed by: markj, grehan
Approved by: grehan (bhyve)
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D27375
where it originally was. The bug introduced in r366267.
o Remove options IOMMU from i386/MINIMAL as we don't have it in
i386/GENERIC.
Reported by: Harry Schmalzbauer <freebsd@omnilan.de>
Reviewed by: kib
Sponsored by: Innovate DSbD
Differential Revision: https://reviews.freebsd.org/D27399
This is a relic from when these instructions weren't supported by the toolchain.
No functional change.
Submitted by: adam_fenn.io
Reviewed by: grehan
Approved by: grehan (bhyve)
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D27130
i386 and the rest of supported architectures by defining KERNLOAD in the
vmparam.h and getting rid of magic constant in the linker script, which albeit
documented via comment but isn't programmatically accessible at a compile time.
Use KERNLOAD to eliminate another (matching) magic constant 100 lines down
inside unremarkable TU "copy.c" 3 levels deep in the EFI loader tree.
Reviewed by: markj
Approved by: markj
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D27355