d_mediasize
CD_FLAG_VALID_TOC is not required for setting those media properties.
PR: kern/145385
Submitted by: Juergen Lock <nox@jelal.kn-bremen.de>
a slightly different version
Tested by: Pavel Sukhoy <sukhoy@ripn.net>,
Markus Wild <m.wild@cybernet.ch>,
Juergen Lock <nox@jelal.kn-bremen.de>,
uqs
MFC after: 1 week
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
When trying to read scratched or damaged CDs and DVDs, the default
mechanism is sub-optimal. Programs like ddrescue do much better if
you turn off retries entirely, since their algorithms are designed
scan big areas fast, then winnow the areas down. Turning off retries
speeds these programs up by as much as 20x, since the drive is able to
'stream past' many small errors...
The sysctl/tunable kern.cam.cd.retry_count controls this. That
defaults to '4' (for a total of 5 attempts). Setting to 0 turns off
all retry attempts.
Reviewed by: scottl@
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
the underlying drive had been hot-unplugged from the system. Here
is a specific example. Filesystem code had opened /dev/da1s1e.
Subsequently, the drive was hot-unplugged. This (correctly) caused
all of the associated /dev/da1* entries to be deleted. When the
filesystem later realized that the drive was gone it closed the
device, reducing the write-access counts to 0 on the geom providers
for da1s1e, da1s1, and da1. This caused geom to re-taste the
providers, resulting in the devices being created again. When the
drive was hot-plugged back in, it resulted in duplicate /dev entries
for da1s1e, da1s1, and da1.
This fix adds a new disk_gone() function which is called by CAM when a
drive goes away. It orphans all of the providers associated with the
drive, setting an error condition of ENXIO in each one. In addition,
we prevent a re-taste on last close for writing if an error condition
has been set in the provider.
Sponsored by: Isilon Systems
Reviewed by: phk
MFC after: 1 week
succeed if there was no media in the drive.
This was broken in rev 1.72 when the media check was added to cdioctl().
For now, check the ioctl group to decide whether to check for media or not.
(We only need to check for media on CD-specific ioctls.)
Reported by: bland
MFC after: 3 days
providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that
result has to be placed into kernel space not user space. In the long run
more generic solution has to be designed WRT emulating various ioctl()s
that operate on userspace buffers, but right now there is only one such
ioctl() is emulated, so that it makes little sense.
MFC after: 2 weeks
sectorsize in order to avoid a lot of checks around various divisions etc.
Enforce the sectorsize being > 0 with a KASSERT on successful open.
Fix scsi_cd.c to return 2k sectors when no media inserted.
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
instead of retrying them blindly.
This should fix some of the problems people have been having with cdrom
drives taking a long time to probe. This should also eliminate the need
for the initial TUR in cdsize().
cam_periph.c: Don't keep retrying if the error we get back is a fatal
error. This should help us detect the transition from
"Logical unit not ready, cause not reportable" to "Medium
not present" in the "TUR many" handler. (The TUR many
handler gets triggered for Logical unit not ready, cause
not reportable errors.)
scsi_cd.c: Remove the initial test unit ready in cdsize(). Hopefully
it isn't necessary after the above change.
Submitted by: gibbs (mostly)
Tested by: peter
MFC After: 2 weeks
has been initialized.
(cdsysctlinit): Set flag CD_FLAG_SCTX_INIT after sysctl_ctx has been
initialized.
This resolves a panic encountered when a cd drive is sucessfully probed
but fails to attach.
Reviewed by: ken
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
For the floppy driver, use fdcontrol to manipulate density selection.
For the CD drivers, the 'a' and 'c' suffix is without actual effect and
any applications insisting on it can be satisfied with a symlink:
ln -s /dev/cd0 /dev/cd0a
Ongoing discussion may result in these pieces of code being removed before
the 5-stable branch as opposed to after.
out of cdregister() and daregister(), which are run from interrupt context.
The sysctl code does blocking mallocs (M_WAITOK), which causes problems
if malloc(9) actually needs to sleep.
The eventual fix for this issue will involve moving the CAM probe process
inside a kernel thread. For now, though, I have fixed the issue by moving
dynamic sysctl variable creation for these two drivers to a task queue
running in a kernel thread.
The existing task queues (taskqueue_swi and taskqueue_swi_giant) run in
software interrupt handlers, which wouldn't fix the problem at hand. So I
have created a new task queue, taskqueue_thread, that runs inside a kernel
thread. (It also runs outside of Giant -- clients must explicitly acquire
and release Giant in their taskqueue functions.)
scsi_cd.c: Remove sysctl variable creation code from cdregister(), and
move it to a new function, cdsysctlinit(). Queue
cdsysctlinit() to the taskqueue_thread taskqueue once we
have fully registered the cd(4) driver instance.
scsi_da.c: Remove sysctl variable creation code from daregister(), and
move it to move it to a new function, dasysctlinit().
Queue dasysctlinit() to the taskqueue_thread taskqueue once
we have fully registered the da(4) instance.
taskqueue.h: Declare the new taskqueue_thread taskqueue, update some
comments.
subr_taskqueue.c:
Create the new kernel thread taskqueue. This taskqueue
runs outside of Giant, so any functions queued to it would
need to explicitly acquire/release Giant if they need it.
cd.4: Update the cd(4) man page to talk about the minimum command
size sysctl/loader tunable. Also note that the changer
variables are available as loader tunables as well.
da.4: Update the da(4) man page to cover the retry_count,
default_timeout and minimum_cmd_size sysctl variables/loader
tunables. Remove references to /dev/r???, they aren't used
any longer.
cd.9: Update the cd(9) man page to describe the CD_Q_10_BYTE_ONLY
quirk.
taskqueue.9: Update the taskqueue(9) man page to describe the new thread
task queue, and the taskqueue_swi_giant queue.
MFC after: 3 days
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
cdcleanup(). This fixes sysctl problems ("can't re-use a leaf") when
someone adds another peripheral at the same unit number. (e.g. rescan da0,
it goes away, then rescan again and da0 comes back, but since we haven't
cleaned up the sysctl variables from the last da0 instance, we can't
register the variables for the new instance under the same name.)
Reported by: njl
Tested by: njl
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
