same way it was enabled for Linux binares in linuxulator.
This allows binaries built with -pie. Many ports auto-detect -fPIE support
in GCC 4.2 and build binaries FreeBSD was unable to run.
vmcnts. This can be used to abstract away pcpu details but also changes
to use atomics for all counters now. This means sched lock is no longer
responsible for protecting counts in the switch routines.
Contributed by: Attilio Rao <attilio@FreeBSD.org>
passed zero as exit signal.
GCC 4.2 changes the kernel data segment layout not to have 0
in that memory location. This code ran by luck before and now
the luck has run out.
an APIC ID of 38 for its second CPU):
- Add a new MAX_APIC_ID constant for the highest valid APIC ID for modern
systems.
- Size the various arrays in the MADT, MP Table, and SMP code that are
indexed by APIC IDs to allow for up to MAX_APIC_ID.
- Explicitly go through and assign logical cpu ids to local APICs before
starting any of the APs up rather than doing it while starting up the
APs. This step is now where we honor MAXCPU.
MFC after: 1 week
- Split the intr_table_lock into an sx lock used for most things, and a
spin lock to protect intrcnt_index. Originally I had this as a spin lock
so interrupt code could use it to lookup sources. However, we don't
actually do that because it would add a lot of overhead to interrupts,
and if we ever do support removing interrupt sources, we can use other
means to safely do so w/o locking in the interrupt handling code.
- Replace is_enabled (boolean) with is_handlers (a count of handlers) to
determine if a source is enabled or not. This allows us to notice when
a source is no longer in use. When that happens, we now invoke a new
PIC method (pic_disable_intr()) to inform the PIC driver that the
source is no longer in use. The I/O APIC driver frees the APIC IDT
vector when this happens. The MSI driver no longer needs to have a
hack to clear is_enabled during msi_alloc() and msix_alloc() as a result
of this change as well.
- Add an apic_disable_vector() to reset an IDT vector back to Xrsvd to
complement apic_enable_vector() and use it in the I/O APIC and MSI code
when freeing an IDT vector.
- Add a new nexus hook: nexus_add_irq() to ask the nexus driver to add an
IRQ to its irq_rman. The MSI code uses this when it creates new
interrupt sources to let the nexus know about newly valid IRQs.
Previously the msi_alloc() and msix_alloc() passed some extra stuff
back to the nexus methods which then added the IRQs. This approach is
a bit cleaner.
- Change the MSI sx lock to a mutex. If we need to create new sources,
drop the lock, create the required number of sources, then get the lock
and try the allocation again.
o push much of the i386 and amd64 MD interrupt handling code
(intr_machdep.c::intr_execute_handlers()) into MI code
(kern_intr.c::ithread_loop())
o move filter handling to kern_intr.c::intr_filter_loop()
o factor out the code necessary to mask and ack an interrupt event
(intr_machdep.c::intr_eoi_src() and intr_machdep.c::intr_disab_eoi_src()),
and make them part of 'struct intr_event', passing them as arguments to
kern_intr.c::intr_event_create().
o spawn a private ithread per handler (struct intr_handler::ih_thread)
with filter and ithread functions.
Approved by: re (implicit?)
VM_PHYSSEG_SPARSE depending on whether the physical address space is
densely or sparsely populated with memory. The effect of this
definition is to determine which of two implementations of
vm_page_array and PHYS_TO_VM_PAGE() is used. The legacy
implementation is obtained by defining VM_PHYSSEG_DENSE, and a new
implementation that trades off time for space is obtained by defining
VM_PHYSSEG_SPARSE. For now, all architectures except for ia64 and
sparc64 define VM_PHYSSEG_DENSE. Defining VM_PHYSSEG_SPARSE on ia64
allows the entirety of my Itanium 2's memory to be used. Previously,
only the first 1 GB could be used. Defining VM_PHYSSEG_SPARSE on
sparc64 allows USIIIi-based systems to boot without crashing.
This change is a combination of Nathan Whitehorn's patch and my own
work in perforce.
Discussed with: kmacy, marius, Nathan Whitehorn
PR: 112194
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.
The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.
MFC after: 1 month
fault. The previous method zero'd out the page tables, invalidated the
TLB, and then entered a spin loop. The idea was that the instruction after
the TLB invalidate would result in a page fault and the page fault and
subsequent double fault wouldn't be able to determine the physical page
for their fault handlers' first instruction. This stopped working when
PGE (PG_G PTE/PDE bit) support was added as a TLB invalidate via %cr3
reload doesn't clear TLB entries with PG_G set. Thus, the CPU was still
able to map the virtual address for the spin loop and happily performed
its infinite loop.
The triple fault now uses a much more deterministic sledge-hammer approach
to generate a triple fault. First, the IDT descriptor is set to point to
an empty IDT, so any interrupts (including a double fault) will instantly
fault. Second, we trigger a int 3 breakpoint to force an interrupt and
kick off a triple fault.
MFC after: 3 days
the introduction of priv(9) and MAC Framework entry points for privilege
checking/granting. These entry points exactly aligned with privileges and
provided no additional security context:
- mac_check_sysarch_ioperm()
- mac_check_kld_unload()
- mac_check_settime()
- mac_check_system_nfsd()
Add mpo_priv_check() implementations to Biba and LOMAC policies, which,
for each privilege, determine if they can be granted to processes
considered unprivileged by those two policies. These mostly, but not
entirely, align with the set of privileges granted in jails.
Obtained from: TrustedBSD Project
vm.kmem_size_min. Useful when using ZFS to make sure that vm.kmem size will
be at least 256mb (for example) without forcing a particular value via vm.kmem_size.
Approved by: njl (mentor)
Reviewed by: alc
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
watchdog might hide the succesful arming of an earlier one. Accept that on
failing to arm any watchdog (because of non-supported timeouts) EOPNOTSUPP is
returned instead of the more appropriate EINVAL.
MFC after: 3 days
code.
# There is some question about whether this code is even relevant any
# longer (it dates back to prehistoric times, i.e. present in r1.1),
# especially on amd64.
Reviewed by: jhb
cpufreq_pre_change is called before the change, giving each driver a chance
to revoke the change. cpufreq_post_change provides the results of the
change (success or failure). cpufreq_levels_changed gives the unit number
of the cpufreq device whose number of available levels has changed. Hook
in all the drivers I could find that needed it.
* TSC: update TSC frequency value. When the available levels change, take the
highest possible level and notify the timecounter set_cputicker() of that
freq. This gets rid of the "calcru: runtime went backwards" messages.
* identcpu: updates the sysctl hw.clockrate value
* Profiling: if profiling is active when the clock changes, let the user
know the results may be inaccurate.
Reviewed by: bde, phk
MFC after: 1 month
temporary mapping created by locore so that the lowest two to four
megabytes can become a permanent identity mapping. This implementation
avoids any use of a large page mapping.
handles when activating a resource via bus_activate_resource() rather than
doing some of the work in bus_alloc_resource() and some of it in
bus_activate_resource().
One note is that when using isa_alloc_resourcev() on PC-98, drivers now
need to just use bus_release_resource() without explicitly calling
bus_deactivate_resource() first. nyan@ has already fixed all of the PC-98
drivers.
address ranges used by local and I/O APICs in the system. Some systems
also reserve these ranges as system resources via either PnPBIOS or
ACPI, so this device currently attaches after acpi0 and legacy0 so that
the system resources are given precedence.
