Omit unused rates while initializing / dumping Tx power values.
They were not accessed anywhere (except for debugging), so this is
(mostly) no-op.
Tested with
* RTL8188EU, STA mode.
* RTL8812AU, STA mode.
Found by: PVS-Studio
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
Use device-specific Rx buffer size to ensure that data will not be
truncated + add a warning if truncation was detected (the driver
cannot handle this case correctly yet).
Tested with:
- RTL8188CUS, RTL8188EU and RTL8821AU, STA / AP modes.
(disabled by default).
To enable it, dev.rtwn.%d.radar_detection tunable need to be set
to a nonzero value.
Tested with RTL8821AU, AP mode (no radar events were seen - so,
I have no idea if it is really correct / working)
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8903
use r92c_init_rf() rather than r92c_init_rf_common() when sc_init_rf()
callback is invoked.
While here, constantly use RF chain instead of RF path in comment.
Reviewed by: avos
- The Tx power (diff) values should be signed
- Fix an off by one error when reading Tx power (diff) values
Reviewed by: avos, adrian
Differential Revision: https://reviews.freebsd.org/D8571
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
NOTE: some multi-vap configurations (e.g., STA+IBSS) are not stable;
that will be fixed later.
Tested with:
- RTL8188CE, STA + AP mode;
- RTL8188CE, IBSS mode;
- RTL8188CUS, IBSS mode;
- RTL8188EU, IBSS mode.
Relnotes: yes
rtwn_usb: drain USB transfers during device shutdown; this fixes possible
panic with 'options IEEE80211_SUPPORT_SUPERG' during device detach.
Tested with RTL8188CE, STA mode.
Do not try to clear stale Tx descriptor entries when there are some
running vaps; just free node references - rtwn_pci_tx_done() will free
mbufs without creating holes in the Tx descriptor space.
Also, reset only 2 first entries in the beacon ring - other will not be
used anyway.
Tested with RTL8188CE, STA + STA mode.
- Correctly refresh Rx filter when AP (IBSS) vap is created after STA vap.
- Block any RCR updates during TSF correction (IBSS mode).
- Set CBSSID* bits during vap creation, not when it was started / stopped.
- Cache current state to prevent unnecessary register reads.
Tested with RTL8188CE, STA + AP mode.
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
1) Unload mbuf instead of descriptor in rtwn_tx_done().
2) Add more synchronization for device visible mappings before
touching the memory.
3) Improve watchdog timer logic.
Reported and tested by: mva
Approved by: re (gjb)
- Use macros to define rate indices; don't hardcode them in code.
- Add method for 'rate' -> 'rate index' conversion
(and array for the opposite).
- Determine if rate is CCK / OFDM via appropriate macro.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D4837
le*dec / le*enc functions.
Replace net80211 specific macros with system-wide bytestream
encoding/decoding functions:
- LE_READ_2 -> le16dec
- LE_READ_4 -> le32dec
- LE_WRITE_2 -> le16enc
- LE_WRITE_4 -> le32enc
+ drop ieee80211_input.h include, where it was included for these
operations only.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6030
- Start vap(s) (via ieee80211_start_all()) only when initialization
succeeds; stop the first vap otherwise (via ieee80211_stop());
- Do not try to stop a device multiple times
(move (sc->sc_flags & RTWN_RUNNING) check to urtwn_stop_locked()).
Tested by: kevlo
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5058
