- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
has been yanked, this works around a cam recounting bug when
CAM_DEV_UNCONFIGURED is set late in the detach. In certain conditions the
reference to the XPT device would not be released which would cause the usb
explore thread to sleep forever on "simfree", preventing any new usb devices to
be found/ejected on the bus.
This is intended to be a quick workaround to the problem without touching CAM
so it can be merged to 8.0.
Suggested by: mav
MFC after: 3 days
direction even if the actual device is opened for read and
write. Fix fflags check so that the UFM and URIO drivers work.
Reported by: Krassimir Slavchev
Submitted by: hps
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
Note that I also added the usbdev to the list, because the 8813 version
is not yet known there. I might have twisted the sorting there but because
8813 comes before 8818, I added it before that (with _8813 to differentiate)
the item.
PR: 135628
Submitted by: Yoshikazu GOTO <goto at on-link dot jp>
Approved by: imp (mentor, implicit)
part identified as Sunplus Technology Inc. This
happens to sit in a Rosewill RX81U-ES-25A 2.5" SATA
to USB 2.0 external enclosure.
Reviewed by: Hans Petter Selasky
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
it is right for only a tiny fraction of these devices and this
wild-card entry is too broad.
# I run a kernel without this entry at all without ill effects...
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
