are successfully returned by the card (usually due to an abort being issued
as part of timeout recovery). Remove what amounts to an insufficient
KASSERT, and don't overwrite the state value. State should probably be
re-designed, and that will be done with a future commit.
Reported by: phk, bei.io
Reviewed by: imp, mav
Differential Revision: D19677
TPM has a built-in RNG, with its own entropy source.
The driver was extended to harvest 16 random bytes from TPM every 10 seconds.
A new build option "TPM_HARVEST" was introduced - for now, however, it
is not enabled by default in the GENERIC config.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: markm, delphij
Approved by: secteam
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D19620
In the latest Linux kernel revisions the DSA (Distributed
Switch Architecture) device tree binding was changed.
Instead of the top level dsa@ node, the switch and its
ports is represented as a child node of the mdio bus.
With that other modifications were added, such as
relation with the ethernet port of the SoC. Adjust
e6000sw etherswitch and mvneta drivers to that.
Tested on Armada 3720 EspressoBin and Armada 388 Clearfog Pro boards.
Submitted by: Bert JW Regeer <xistence@0x58.com>
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D19036
PIIX4_SMBHSTSTAT_ERR can be set for several reasons that, unfortunately,
cannot be distinguished, but the most typical case is a missing or hung
slave (SMB_ENOACK).
PIIX4_SMBHSTSTAT_FAIL means failed or killed / aborted transaction, so
it's previous mapping to SMB_ENOACK was not ideal.
After this change an smb(4) access to a missing slave results in ENXIO
rather than EIO. To me, that seems to be more appropriate.
MFC after: 3 weeks
This value was being used uninitialized, resulting in predictable issues
on systems with memory-mapped UART registers.
A case could be made that memmap_bus should be declared in a header
rather than being declared in each .c file which needs to refer to it,
but that's a broader style question.
This commit unbreaks hw.uart.console="mm:..." on ARM64.
Submitted by: Greg V
The "access width" value was hard-coded as 2, indicating 32-bit accesses;
instead, use the value specified in the SPCR table.
This unbreaks the console on EC2 "A1" family instances.
Submitted by: Greg V
No functional changes. Replace whitespace by tabs, indent with 4 spaces,
coalesce multi-line shorter than 80 characters,
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
The resource is already being activated in the bus_alloc_resource(),
because the flag RF_ACTIVE is being passed.
Double activation on arm64 is causing kernel panic.
Version of the driver was upgraded to 0.8.4.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Reported-by: Greg V <greg@unrelenting.technology>
Tested-by: cperciva, Greg V <greg@unrelenting.technology>
Obtained from: Semihalf
MFC after: 2 weeks
Sponsored by: Amazon, Inc.
Differential revision: https://reviews.freebsd.org/D19655
as an NS8250 UART.
This is the same as the UART found in EC2 "bare metal" instances,
except that the card vendor shows up as 0x0000 rather than 0x1d0f.
This seems like a bug in the EC2 firmware; but we might as well support
it anyway.
Reported by: Greg V
Recent firmwares prefer to use a different format for viid internally
and this change allows them to do so.
MFC after: 1 week
Sponsored by: Chelsio Communications
From Krzysztof:
The driver built as KLD cannot be unloaded, if this flag is not set.
Submitted by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Reviewed by: shurd@, erj@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D19402
From Jake:
iflib_fl_setup calculates a suitable buffer size for the Rx mbufs based
on the isc_max_frame_size value that drivers setup. This calculation is
repeated by drivers when programming their hardware with the size of
each Rx buffer.
This can lead to a mismatch where the iflib mbuf size is different from
the expected size of the buffer as programmed by the hardware. This can
lead to unexpected results.
If iflib ever wants to support mbuf sizes larger than one page, every
driver must be updated to account for the new possible buffer sizes.
Fix this by calculating the mbuf size prior to calling IFDI_INIT, and
adding the iflib_get_rx_mbuf_sz function which will expose this value to
drivers, so that they do not repeat the same calculation.
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: shurd@, erj@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D19489
Minimalistic PSCI implementation in U-Boot doesn't implement get_version()
method for some SoC. In this case, use PSCI version declared by 'psci' node
in DT as fallback.
MFC after: 2 weeks
- older DT can use 'cpu0-supply' property for power supply binding.
- don't expect that actual CPU frequency is contained in CPU
operational point table, but read current CPU voltage directly from
reguator. Typically, u-boot can set starting CPU frequency to any
value.
MFC after: 2 weeks
Some applications forward from/to host rings most or all the
traffic received or sent on a physical interface. In this
cases it is desirable to have more than a pair of RX/TX host
rings, and use multiple threads to speed up forwarding.
This change adds support for multiple host rings. On registering
a netmap port, the user can specify the number of desired receive
and transmit host rings in the nr_host_tx_rings and nr_host_rx_rings
fields of the nmreq_register structure.
MFC after: 2 weeks
Without this dependency relationship, the linker doesn't find the
flash_register_slicer() function, so kldload fails to load fdt_slicer.ko.
Discussed with: ian@
The forthcoming microcode update will fix a TSX bug by clobbering PMC3
when TSX instructions are executed (even speculatively). There is an
alternate mode where CPU executes all TSX instructions by aborting
them, in which case PMC3 is still available to OS. Any code that
correctly uses TSX must be ready to handle abort anyway.
Since it is believed that FreeBSD population of hwpmc(4) users is
significantly larger than the population of TSX users, switch the
microcode into TSX abort mode whenever a pmc is allocated, and back to
bug avoidance mode when the last pmc is deallocated.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
isci(4) uses deferred loading. Typically on amd64 and i386 non-PAE
the tag does not create any restrictions, but on i386 PAE-tables but
non-PAE configs callbacks might be used.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
writes are running. Some of the cases which are not handled properly in driver are:
1. With R1 fastpath supported, single write from CAM layer can consume 2 MPT frames
at driver/firmware level for fastpath qualification(if fw_outstanding < controller Queue Depth).
Due to this driver has to throttle IOs coming from CAM layer as well as second fastpath
write(of R1 write) against Adapter Queue Depth.
If "fw_outstanding" reaches to adapter queue depth, driver should return IOs from CAM layer with
device busy status.While allocating second MPT frame(corresponding to R1 FP write) also, driver
should ensure fw_outstanding should not exceed adapter QD.
2. For R1 fastpath writes completion, driver decrements "fw_oustanding" counter without
really returning MPT frame to free pool. It may cause IOs(with heavy IOs running, consuming whole
adapter Queue Depth) consuming MPT frames reserved for DCMDs(management commands) and
DCMDs(internal and sent by application) not getting MPT frame will start failing.
Below is one test case to hit the issue described above-
1. Run heavy IOs (outstanding IOs should hit adapter Queue Depth).
2. Run management tool (Broadcom's storcli tool) querying adapter in loop (run command- "storcli64 /c0 show" in loop).
3. Management tool's requests would start failing due to non-availability of free MPT frames as all frames would be consumed by IOs.
Fix: Increment/decrement of "fw_outstanding" counter should be in sync with MPT frame get/return.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: Ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Make sure the enter and leave polling routines can be called multiple times
with same setting. Ignore setting polling or event mode twice. This fixes a
deadlock during shutdown if polling mode was already selected.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The ESGL bit was left uninitialized when executing the REPORT LUNS
ioctl. This could allow a zeroed data buffer to be treated as a
scatter/gather list. The firmware would eventually walk past the end
of the data buffer, potentially find what looked like a valid
address/length pair, and write the result to semi-random memory.
Obtained from: Dell EMC Isilon
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19398
The Command Reference Number (CRN) is part of the FC-Tape features
that we enable when talking to tape drives. It starts at 1, and
goes to 255 and wraps around to 1. There are a number of reset
type conditions that result in the CRN getting reset to 1. These
are detailed in section 4.10 (table 8) of the FCP-4r02b specification.
One of the conditions is when a PRLI (Process Login) is sent by
the initiator, and the Establish Image Pair bit is set in Word 0
of the PRLI.
Previously, the isp(4) driver core sent a notification via
isp_async() that the target had changed or stayed in place, but
there was no indication of whether a PRLI was sent and whether the
Establish Image Pair bit was set.
The result of this was that in some situations, notably
switching back and forth between a direct connection and a switch
connection to a tape drive, the isp(4) driver would fail to reset
the CRN in situations that require it according to the spec. When
the CRN isn't reset in a situation that requires it, the tape drive
then rejects every subsequent command that is sent to the drive.
It is assuming that the commands are being sent out of order.
So, modify the isp(4) driver to include Word 0 of the PRLI command
when it sends isp_async() notifications of target changes. Look at
the Establish Image Pair bit, and reset the CRN if that bit is set.
With this change, I am able to switch a tape drive back and forth
between a direct connection and a switch connection, and the isp(4)
driver resets the CRN when it should.
sys/dev/isp_stds.h:
Add bit definitions for PRLI Word 0.
sys/dev/ispmbox.h:
Add PRLI Word 0 to the port database type, isp_pdb_t.
sys/dev/ispvar.h
Add PRLI Word 0 to fcportdb_t.
sys/dev/isp.c:
Populate the new prli_word0 parameter in the port database.
In isp_pdb_add_update(), add a check to see if the
Establish Image Pair bit is set in PRLI Word 0. If it is,
then that is an additional reason to create a change
notification.
sys/dev/isp_freebsd.c:
In isp_async(), if the device changed or stayed, look at
PRLI Word 0 to see if the Establish Image Pair bit is set.
If it is, reset the CRN if we haven't already.
MFC after: 1 week
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D19472
Intel 3168 uses another EEPROM section to store channel flags;
port missing bits from iwlwifi to make it work.
PR: 230750, 236235
Tested by: Bert JW Regeer <xistence@0x58.com>
MFC after: 3 days
Also, pass control frames to the host while in MONITOR mode and / or
when promiscuous mode is enabled.
Tested with Netgear WG111 v3 (RTL8187B), STA / MONITOR modes.
MFC after: 2 weeks
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
like this:
pqisrc_build_sgl() at pqisrc_build_sgl+0x8d/frame 0xfffffe009e8b7a00
pqisrc_build_raid_io() at pqisrc_build_raid_io+0x231/frame 0xfffffe009e8b7a40
pqisrc_build_send_io() at pqisrc_build_send_io+0x375/frame 0xfffffe009e8b7b00
pqi_request_map_helper() at pqi_request_map_helper+0x282/frame 0xfffffe009e8b7ba0
bus_dmamap_load_ccb() at bus_dmamap_load_ccb+0xd7/frame 0xfffffe009e8b7c00
pqi_map_request() at pqi_map_request+0x9b/frame 0xfffffe009e8b7c70
pqisrc_io_start() at pqisrc_io_start+0x55c/frame 0xfffffe009e8b7d50
smartpqi_cam_action() at smartpqi_cam_action+0xb8/frame 0xfffffe009e8b7de0
xpt_run_devq() at xpt_run_devq+0x30a/frame 0xfffffe009e8b7e40
xpt_action_default() at xpt_action_default+0x94b/frame 0xfffffe009e8b7e90
dastart() at dastart+0x33b/frame 0xfffffe009e8b7ee0
xpt_run_allocq() at xpt_run_allocq+0x1a2/frame 0xfffffe009e8b7f30
dastrategy() at dastrategy+0x71/frame 0xfffffe009e8b7f60
g_disk_start() at g_disk_start+0x351/frame 0xfffffe009e8b7fc0
g_io_request() at g_io_request+0x3cf/frame 0xfffffe009e8b8010
g_part_start() at g_part_start+0x120/frame 0xfffffe009e8b8090
g_io_request() at g_io_request+0x3cf/frame 0xfffffe009e8b80e0
zio_vdev_io_start() at zio_vdev_io_start+0x4b2/frame 0xfffffe009e8b8140
zio_execute() at zio_execute+0x17c/frame 0xfffffe009e8b8180
zio_nowait() at zio_nowait+0xc4/frame 0xfffffe009e8b81b0
vdev_queue_io_done() at vdev_queue_io_done+0x138/frame 0xfffffe009e8b81f0
zio_vdev_io_done() at zio_vdev_io_done+0x151/frame 0xfffffe009e8b8220
zio_execute() at zio_execute+0x17c/frame 0xfffffe009e8b8260
taskqueue_run_locked() at taskqueue_run_locked+0x10c/frame 0xfffffe009e8b82c0
taskqueue_thread_loop() at taskqueue_thread_loop+0x88/frame 0xfffffe009e8b82f0
fork_exit() at fork_exit+0x84/frame 0xfffffe009e8b8330
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe009e8b8330
Reviewed by: deepak.ukey_microsemi.com, sbruno
MFC after: 2 weeks
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D19470
trying to use disk_add_alias() to make spi* an alias for mx25l*. It turns
out disk_add_alias() works for partitions, but not slices, and that's hard
to fix.
This change is, in effect, a partial revert of r344526.
The mips world relies on the existence of flashmap names formatted as
/dev/flash/spi0s.name, whereas pretty much nothing relies on at45d devices
using the /dev/spi* names (because until recently the at45d driver didn't
even work reliably). So this change makes mx25l devices the sole owner of
the /dev/flash/spi* namespace, which actually makes some sense because it is
a SpiFlash(tm) device, so flash/spi isn't a horrible name.
Reported by: Mori Hiroki <yamori813@yahoo.co.jp>
retries.
When resetting the controller, we abort I/O. Prior to this fix, we
printed a ton of abort messages for I/O that we're going to
retry. This imparts no useful information. Stop printing them unless
our retry count is exhausted. Clarify code for when we don't retry,
and remove useless arg to a routine that's always called with it
as 'true'. All the other debug is still printed (including multiple
reset messages if we have multiple timeouts before the taskqueue
runs the actual reset) so that we know when we reset.
Reviewed by: jimharris@, chuck@
Differential Revision: https://reviews.freebsd.org/D19431
mlx4_en_stop_port() calls mlx4_en_put_qp() which can refer the link level
address of the network interface, which in turn will be freed by the
network interface detach function. Make sure the port is stopped
before detaching the network interface.
MFC after: 1 week
Sponsored by: Mellanox Technologies
It can happen during shutdown that the lock will recurse when the mlx4en(4)
instance is part of a lagg interface. Call ether_ifdetach() unlocked.
Backtrace:
panic(): _sx_xlock_hard: recursed on non-recursive sx &mdev->state_lock
_sx_xlock_hard()
_sx_xlock()
mlx4_en_ioctl()
if_setlladdr()
lagg_port_destroy()
lagg_port_ifdetach()
if_detach()
mlx4_en_destroy_netdev()
mlx4_en_remove()
mlx4_remove_device()
mlx4_unregister_device()
mlx4_unload_one()
mlx4_shutdown()
linux_pci_shutdown()
bus_generic_shutdown()
MFC after: 1 week
Sponsored by: Mellanox Technologies
Chacha20 with a 256 bit key and 128 bit counter size is a good match for an
AES256-ICM replacement.
In userspace, Chacha20 is typically marginally slower than AES-ICM on
machines with AESNI intrinsics, but typically much faster than AES on
machines without special intrinsics. ChaCha20 does well on typical modern
architectures with SIMD instructions, which includes most types of machines
FreeBSD runs on.
In the kernel, we can't (or don't) make use of AESNI intrinsics for
random(4) anyway. So even on amd64, using Chacha provides a modest
performance improvement in random device throughput today.
This change makes the stream cipher used by random(4) configurable at boot
time with the 'kern.random.use_chacha20_cipher' tunable.
Very rough, non-scientific measurements at the /dev/random device, on a
GENERIC-NODEBUG amd64 VM with 'pv', show a factor of 2.2x higher throughput
for Chacha20 over the existing AES-ICM mode.
Reviewed by: delphij, markm
Approved by: secteam (delphij)
Differential Revision: https://reviews.freebsd.org/D19475
