lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
Add back in a scheme to emulate old type major/minor numbers via hooks into
stat, linprocfs to return major/minors that Linux app's expect. Currently
only /dev/null is always registered. Drivers can register via the Linux
type shim similar to the ioctl shim but by using
linux_device_register_handler/linux_device_unregister_handler functions.
The structure is:
struct linux_device_handler {
char *bsd_driver_name;
char *linux_driver_name;
char *bsd_device_name;
char *linux_device_name;
int linux_major;
int linux_minor;
int linux_char_device;
};
Linprocfs uses this to display the major number of the driver. The
soon to be available linsysfs will use it to fill in the driver name.
Linux_stat uses it to translate the major/minor into Linux type values.
Note major numbers are dynamically assigned via passing in a -1 for
the major number so we don't need to keep track of them.
This is somewhat needed due to us switching to our devfs. MegaCli
will not run until I add in the linsysfs and mfi Linux compat changes.
Sponsored by: IronPort Systems
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
o Add the scc(4) manpage to the build.
o Update the uart(4) manpage to account for scc(4).
o Update the uart(4) module build to include support for scc(4).
controllers typically have multiple channels and support a number
of serial communications protocols. The scc(4) driver is itself
an umbrella driver that delegates the control over each channel
and mode to a subordinate driver (like uart(4)).
The scc(4) driver supports the Siemens SAB 82532 and the Zilog
Z8530 and replaces puc(4) for these devices.
is derived from the phrase 'MegaRAID Firmware Interface' used by LSI. This
driver provides a block interface to logical disks on the card and a minimal
management device. It is MPSAFE, INTR_FAST, and 64-bit capable.
Thanks to Dell for providing hardware to test with and IronPort for
sponsoring the work.
Sponsored by: Dell, Ironport
MFC After: 3 days
- <netipx> headers [1]
- IPX library (libipx)
- IPX support in ifconfig(8)
- IPXrouted(8)
- new MK_NCP option
New MK_NCP build option controls:
- <netncp> and <fs/nwfs> headers
- NCP library (libncp)
- ncplist(1) and ncplogin(1)
- mount_nwfs(8)
- ncp and nwfs kernel modules
User knobs: WITHOUT_IPX, WITHOUT_IPX_SUPPORT, WITHOUT_NCP.
[1] <netsmb/netbios.h> unconditionally uses <netipx> headers
so they are still installed. This needs to be dealt with.
which is normal for own files of a device driver.
DEV_FOO should be used if an unrelated kernel file needs to know of
the `foo' driver's static presence. Obviously, module source files
should never use DEV_*.
enabled by default in NETSMB and smbfs.ko.
With the most of modern SMB providers requiring encryption by
default, there is little sense left in keeping the crypto part
of NETSMB optional at the build time.
This will also return smbfs.ko to its former properties users
are rather accustomed to.
Discussed with: freebsd-stable, re (scottl)
Not objected by: bp, tjr (silence)
MFC after: 5 days
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
and want to have crypto support loaded as KLD. By moving zlib to separate
module and adding MODULE_DEPEND directives, it is possible to use such
configuration without complication. Otherwise, since IPSEC is linked with
zlib (just like crypto.ko) you'll get following error:
interface zlib.1 already present in the KLD 'kernel'!
Approved by: cognet (mentor)
Otherwise a kernel build would break in the coda5 module if the main
kernel conf file enabled CODA_COMPAT_5, too. Redefined symbols are
strictly disallowed by -Werror.
To overcome this issue, introduce a different symbol indicating coda5
build, CODA5_MODULE, and translate it to CODA_COMPAT_5 appropriately
in /sys/coda/coda.h.
MFC after: 3 days
inside !if defined(KERNBUILDDIR).
Utilize the fact the module will support all frames by default --
it needs no ETHER_* options unless some frames need to be disabled.
Fix the comment respectively.
Don't forget to create fake opt_ef.h if no ETHER_* are set.
MFC after: 3 days
