is running on other cpu, the CALLOUT_PENDING flag is temporarily
cleared. Then, callout_stop() on this, in fact active, callout fails
because CALLOUT_PENDING is not set, and callout_stop() returns 0.
Now, in sleepq_check_timeout(), the failed callout_stop() causes the
sleepq code to execute mi_switch() without even setting the wmesg,
since the switch-out is supposed to be transient. In fact, the thread
is put off the CPU for full timeout interval, instead of being put on
runq immediately. Until timeout fires, the process is unkillable for
obvious reasons.
Fix this by marking the migrating callouts with CALLOUT_DFRMIGRATION
flag. The flag is cleared by callout_stop_safe() when the function
detects a migration, besides returning the success. The softclock()
rechecks the flag for migrating callout and cancels its execution if
the flag was cleared meantime.
PR: misc/166340
Reported, debugging traces provided and tested by:
Christian Esken <christian.esken trivago com>
Reviewed by: avg, jhb
MFC after: 1 week
Enqueue thread in LIFO, this can cause starvation, but it gives better
performance. Use _thr_queuefifo to control the frequency of FIFO vs LIFO,
you can use environment string LIBPTHREAD_QUEUE_FIFO to configure the
variable.
Cleaner solution (e.g. adding another header) should be done here.
Original log:
Move several enums and structures required for L2 filtering from ip_fw_private.h to ip_fw.h.
Remove ipfw/ip_fw_private.h header from non-ipfw code.
Requested by: luigi
Approved by: kib(mentor)
Lagg(4) restricts the type of packet that may be sent directly to a child
port, to avoid undesired output from accidental misconfiguration.
Previously only ETHERTYPE_PAE was permitted.
BPF writes to a lagg(4) child port are presumably intentional, so just
allow them, while still blocking other packets that should take the
aggregation path.
PR: kern/138620
Approved by: thompsa@
another process is in open() or stat() for the device node, then
close() from the owning process does not result in cdevsw close
method call. This fixes the pemanent "Device busy" seen.
Changed the sndstat_lock from mutex to sx. This allows to extend
the region covered by the lock, to include the uiomove() call in
sndstat_read() and bufptr increment. This fixes the "panic:
sbuf_put_byte called with finished or corrupt sbuf" seen.
In collaboration with: kib
MFC after: 1 week
code and which had only stub implementations or no implementation on all
platforms. Makes gxemul compile.
Hinted by: rwatson
MFC after: 3 weeks
X-MFC by: rwatson:
if the accounting log file is atomically replaced with a new file
(such as during log rotation).
- Simplify accounting log rotation a bit. There is no need to re-run
accton(8) after renaming the new log file to it's real name.
PR: kern/167321
Tested by: Jeremy Chadwick
1) Always implement missing bus space methods using a panic() stub rather
than a NULL pointer. This appeared not to trip up any existing device
drivers, but due to the nature of the devices I'm supporting locally,
I'm making use of some of the more obscure busspace methods, and
panic() is a preferred failure mode. For example, do this for the
setregion methods.
2) Hook up several existing busspace method implementations that were
provided in the file, but not actually present in the methods
structure. Especially, single-byte bus I/O routines. This should
allow bugs to be fixed in the Atheros 802.11 driver.
There are still some remaining unimplemented methods that would be
desirable to implement -- especially, 64-bit I/O calls that would
observably accelerate device performance on FPGA-based soft CPU cores
that are typically clocked an order of magnitude slower than
conventional hard core CPUs, but that remains for another day.
MFC after: 3 weeks
Discussed with: jmallett, scottl
Sponsored by: DARPA, AFRL
entirely of one machdep file lifted from the MALTA port, as well as
a low-level console and tty driver for the gxemul debugging console
device (the emulators stdio). As with many low-level embedded and
hypervisor console devices, it is polled only, so we drive TTY I/O
from a callout; we are perhaps a bit too aware of the MIPS physical
maps in order to attach the console before newbus comes to life.
The sample kernel configuration depends on an MD-based root file
system, which is not provided. However, any 64-bit, big-endian
userspace image (such as one generated for MALTA) should work.
This will hopefully be supplemented by additional device drivers for
gxemul-specific hardware simulations from Juli Mallett. We have
found oldtestmips quite useful for testing and improving aspects of
the MIPS port, so it's worth supporting better in FreeBSD.
Requested by: theraven, jmallett
Sponsored by: DARPA, AFRL
MFC after: 3 weeks
* Flesh out the PLL configuration fetch function, which will return the PLL
configuration based on the unit number and speed.
* Remove the PLL speed config logic from the AR71xx/AR91xx chip PLL config
function - pass in a 'pll' value instead.
* Modify arge_set_pll() to:
+ fetch the PLL configuration
+ write the PLL configuration
+ update the MII speed configuration.
This will allow if_arge to override the PLL configuration as required.
Obtained from: Linux/Atheros/OpenWRT
* Add a new method to set the MII mode - GMII, RGMII, RMII, MII.
+ arge0 supports all four (two for non-Gige interfaces.)
+ arge1 only supports two (one for non-gige interfaces.)
* Set the MII clock speed when changing the MAC PLL speed.
+ Needed for AR91xx and AR71xx; not needed for AR724x.
Tested:
* AR71xx only, I'll do AR913x testing tonight and fix whichever issues
creep up.
TODO:
* Implement the missing AR7242 arge0 PLL configuration, but don't
adjust the MII speed accordingly.
* .. the AR7240/AR7241 don't require this, so make sure it's not set
accidentally.
Bugs (not fixed here):
* Statically configured arge speeds are still broken - investigate why
that is on the AP96 board. Autonegotiate is working fine, but there
still seems to be an occasionally heavy packet loss issue.
Obtained from: Linux/Atheros/OpenWRT
- Align the RX buffers on the cache line size, otherwise the requirement
of partial cache line flushes on every are pretty much guaranteed. [1]
- Make the code setting the RX timeout match its comment (apparently,
start and stop bits were missed in the previous calculation). [1]
- Cover the busdma operations in at91_usart_bus_{ipend,transmit}() with
the hardware mutex, too, so these don't race against each other.
- In at91_usart_bus_ipend(), reduce duplication in the code dealing with
TX interrupts.
- In at91_usart_bus_ipend(), turn the code dealing with RX interrupts
into an else-if cascade in order reduce its complexity and to improve
its run-time behavior.
- In at91_usart_bus_ipend(), add missing BUS_DMASYNC_PREREAD calls on
the RX buffer map before handing things over to the hardware again. [1]
- In at91_usart_bus_getsig(), used a variable of sufficient width for
storing the contents of USART_CSR.
- Use KOBJMETHOD_END.
- Remove an unused header.
Submitted by: Ian Lepore [1]
Reviewed by: Ian Lepore
MFC after: 1 week
V100, the firmware is known to be broken and not allowing to simultaneously
open disk devices, causing attempts to boot from a mirror or RAIDZ to cause
a crash. This will be worked around later. The firmwares of newer sun4u models
don't seem to exhibit this problem though.
Steps for ZFS booting:
1. create VTOC8 label
# gpart create -s vtoc8 da0
2. add partitions, f.e.:
# gpart add -t freebsd-zfs -s 60g da0
# gpart add -t freebsd-swap da0
resulting in something like:
# gpart show
=> 0 143331930 da0 VTOC8 (68G)
0 125821080 1 freebsd-zfs (60G)
125821080 17510850 2 freebsd-swap (8.4G)
3. create zpool
# zpool create bunker da0a
or for mirror/RAIDZ (after preparing additional disks as in steps 1. + 2.):
# zpool create bunker mirror da0a da1a
# zpool create bunker raidz da0a da1a da2a ...
4. set bootfs
# zpool set bootfs=bunker bunker
5. install zfsboot
# zpool export bunker
# gpart bootcode -p /boot/zfsboot da0
6. write zfsloader to the ZFS Boot Block (so far, there's no dedicated tool
for this, so dd(1) has to be used for this purpose)
When using mirror/RAIDZ, step 4. and the dd(1) invocation should be repeated
for the additional disks in order to be able to boot from another disk in
case of failure.
# sysctl kern.geom.debugflags=0x10
# dd if=/boot/zfsloader of=/dev/da0a bs=512 oseek=1024 conv=notrunc
# zpool import bunker
7. install system on ZFS filesystem
Don't forget to set 'zfs_load="YES"' and vfs.root.mountfrom="zfs:bunker" in
loader.conf as well as 'zfs_enable="YES"'in rc.conf.
8. copy zpool.cache to the ZFS filesystem
cp -p /boot/zfs/zpool.cache /bunker/boot/zfs/zpool.cache
9. set mountpoint
# zfs set mountpoint=/ bunker
10. Now, given that aliases for all disks in the zpool exists (check with
the `devalias` command on the boot monitor prompt) and disk0 corresponds
to da0 (likewise for additional disks), the system can be booted from the
ZFS with:
{1} ok boot disk0
PR: 165025
Submitted by: Gavin Mu
* Modified hwmp_recv_preq:
o cleaned up code, removed rootmac variable because preq->origaddr
is the root when we recevie a Proactive PREQ;
o Modified so that a PREP in response of a Proactive PREQ is unicast,
a PREP is ALWAYS unicast;
* Modified hwmp_recv_prep:
o Before we mark a route to be valid we should remove the discovery
flag and then mark it valid in such a way we wont lose the isgate flag;
Approved by: adrian
* Added a new discovery flag IEEE80211_MESHRT_FLAGS_DISCOVER;
* Modified ieee80211_ioctl.h to include IEEE80211_MESHRT_FLAGS_DISCOVER;
* Added hwmp_rediscover_cb, which will be called by a timeout to do
rediscovery if we have not reach max number of preq discovery;
* Modified hwmp_discover to setup a callout for path rediscovery;
* Added to ieee80211req_mesh_route to have a back pointer to ieee80211vap
for the discovery callout context;
* Modified mesh_rt_add_locked arguemnt from ieee80211_mesh_state to
ieee80211vap, this because we have to initialize the above back pointer;
Approved by: adrian
* Renamed IEEE80211_ELEMID_MESHPANN to IEEE80211_ELEMID_MESHGANN according to
amendment;
* Added IEEE80211_IOC_MESH_GATE that controls whether Mesh Gate Announcement
is activated or not;
* Renamed all flags from Portal to Gate in HWMP frames;
* Removed IEEE80211_ACTION_MESHPANN enum cause its part of the Mesh Action
category now as per amendment;
* Renamed IEEE80211_MESHFLAGS_PORTAL to IEEE80211_MESHFLAGS_GATE in
ieee80211_mesh_state flags;
* Modified ieee80211_hwmp.c/ieee80211_mesh.c to use new GATE flags;
Approved by: adrian
* Introduced a new HWMP sysctl, Root Confirmation Interval;
* Added hr_lastrootconf to hwmp_route, is for ratecheck for a specific ROOT;
* We missed reading RANN.interval subfield from a RANN frame before;
* Updated hwmp_recv_rann according to amendment, see comments;
Approved by: adrian
* Added mpp_senderror for Mesh Path Selection protocol;
* Added hwmp_senderror that will send an HWMP PERR according to the
supplied reason code;
* Call mpp_senderror when deleting a route with correct reason code
for whether the route is marked proxy or not;
* Call mpp_senderror when trying to forward an individually addressed
frame and there is no forwarding information;
Approved by: adrian
* When receiving a Proactive PREQ dont return after processing it but propagate;
* When we propagate we should not enforce ratechecking;
* Added checking for multiple pred ID detection;
* Storing proxy orig address when PREQ is not for us;
Approved by: adrian
