for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
2) s/MODLOAD/KMODLOAD/ to be consistent with the rest of the variables
(KMOD, KMODOWN, KMODGRP, etc) and definition of MODLOAD/UNLOAD in the
Makefile of the ATAPI module
3) textual fixups
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
due to the fact that there are non-MII cards supported by the same
driver and I don't have all of the cards available for testing. There's
also the 3c905B-COMBO which has MII, AUI and BNC media ports all in one
package. Supporting the COMBO is difficult because we have to add the
10base5 and 10base2 media types to the same ifmedia struct as the
MII-attached types, however there is no way to force the miibus and
child PHYs into existence before xl_attach() completes, so there is
no ifmedia struct available in xl_attach(). What we do inistead is
use the mediainit method as a callback: when a child PHY is attached,
it calls the miibus mediainit routine which selects a default media.
This routing also calls the NIC driver's mediainit method (if it
implements one) at which point we can safely add the other media
types.
discussed on current.
The following variables are defined (for now):
osname (defaults to "Linux")
Allow users to change the name of the OS as returned by uname(2),
specially added for all those Linux Netscape users and statistics
maniacs :-) We now have what we all wanted!
osrelease (defaults to "2.2.5")
Allow users to change the version of the OS as returned by uname(2).
Since -current supports glibc2.1 now, change the default to 2.2.5
(was 2.0.36).
oss_version (defaults to 198144 [0x030600])
This one will be used by the OSS_GETVERSION ioctl (PR 12917) which I
can commit now that we have the MIB. The default version number is the
lowest version possible with the current 'encoding'.
A note about imprisoned processes (see jail(2)):
These variables are copy-on-write (as suggested by phk). This means that
imprisoned processes will use the system wide value unless it is written/set
by the process. From that moment on, a copy local to the prison will be
used.
A note about the implementation:
I choose to add a single pointer to struct prison, because I didn't like the
idea of changing struct prison every time I come up with a new variable. As
a side effect, the extra storage is only needed when a variable is set from
within the prison. This also minimizes kernel bloat when the Linuxulator is
not used; both compiled in or as a module.
Reviewed by: bde (first version only) and phk
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
that doesn't have it. This is achieved by having minimal do-nothing stubs
enabled when there are no bpfilter devices configured.
Driver modules should be built with BPF enabled for maximum
convenience (but can be built without it for maximum performance).
.gdbinit.crash contains a top-level .gdbinit suitable for debugging
crash dumps
.gdbinit.serial contains a top-level .gdbinit suitable for serial
debugging
Each of these two files reads the following files:
.gdbinit.kernel: This file contains general macros suitable for kernel
debugging. It is not related to vinum
.gdbinit.vinum: This file contains macros specific to debugging
vinum.
.gdbinit.paths: Contains information about the location of the source
and object files on the system.
.gdbinit.crash contains a top-level .gdbinit suitable for debugging
crash dumps
.gdbinit.serial contains a top-level .gdbinit suitable for serial
debugging
Each of these two files reads the following files:
.gdbinit.kernel: This file contains general macros suitable for kernel
debugging. It is not related to vinum
.gdbinit.vinum: This file contains macros specific to debugging
vinum.
.gdbinit.paths: Contains information about the location of the source
and object files on the system.
The old VN device broke in -4.x when the definition of B_PAGING
changed. This patch fixes this plus implements additional capabilities.
The new VN device can be backed by a file ( as per normal ), or it can
be directly backed by swap.
Due to dependencies in VM include files (on opt_xxx options) the new
vn device cannot be a module yet. This will be fixed in a later commit.
This commit delimitted by tags {PRE,POST}_MATT_VNDEV
world breakage (mainly for cross-world cases). The world Makefile
attempts to build tools static so that nonexistent or wrong shared
libraries and interpreters don't get used. This is broken anyway
since the world Makefile doesn't know about svr4_genassym.
Force building svr4_genassym static. This is part of "fixing"
aout-to-elf-build breakage. aout-to-elf-build abuses NOTOOLS to
avoid rebuilding all the aout tools. This saves time and avoids
some complications. However, it breaks all the internal tools --
they get linked to target libraries which might not work. Cases
where the host can run the target's static libraries are "fixed"
by encrufting all Makefiles that build internal tools to build the
tools static.
Don't add .depend to CLEANFILES -- it just breaks the separation of
`make cleandepend' from `make clean'.
Removed some superflous explicit dependencies.
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
XXX It probably makes sense to have a flag for bsd.kern.mk to avoid these
rules.
XXX IO_NDELAY seems to be the main reason for it, when used in a cdevsw
read or write "flag" context. Perhaps a redundant declaration
somewhere like sys/conf.h might help remove the need for vnode.h in
these device drivers in the first place.
capabilities, but should be a good start... Well, sort of.
It can handle W*ndows 256 color BMP file. (Other color depth probably
won't work.) The size of the image must be 320x200 or less. *sigh*
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
Change the ELF registration/unregistration scheme to be less error prone.
Adding a new brand requires a single addition to linux_brandlist instead of
modifying linux_load(), linux_unload(), and linux_elf_init().
Approved by: jkh
Reviewed by: msmith
Kazu writes:
The VESA support code requires vm86 support. Make sure your kernel
configuration file has the following line.
options "VM86"
If you want to statically link the VESA support code to the kernel,
add the following option to the kernel configuration file.
options "VESA"
The vidcontrol command now accepts the following video mode names:
VESA_132x25, VESA_132x43, VESA_132x50, VESA_132x60, VESA_800x600
The VESA_800x600 mode is a raster display mode. The 80x25 text will
be displayed on the 800x600 screen. Useful for some laptop computers.
vidcontrol accepts the new `-i <info>' option, where <info> must be
either `adapter' or `mode'. When the `-i adapter' option is given,
vidcontrol will print basic information (not much) on the video
adapter. When the `-i mode' option is specified, vidcontrol will
list video modes which are actually supported by the video adapter.
Submitted by: Kazutaka YOKOTA yokota@FreeBSD.ORG
leftover files in /tmp. Script slightly modified from PR version
to use fewer processes.
PR: i386/7725
Submitted by: Stefan Eggers seggers@semyam.dinoco.de
not actually work for cross compiling, but that is another problem.)
Honor LDFLAGS for building internal tools. (Tools should normally
be built static to avoid problems with picking up target shared
libraries. bsd.kmod doesn't set -static yet, and has some problems
with `LDFLAGS=-static ...' in the environment.)
NFS_*TIMO should possibly be converted to sysctl vars (jkh's suggestion),
but in some cases it looks like nfs keeps a copy of the value in a struct
hash sizes are already ifdef'd KERNEL, so there aren't userland inpact
from them...
not quite correct, because the Makefiles in lkm/syscons don't set up the
`machine' symlink, but other, more volatile headers in <machine> are
already used.
screen size was changed while the screen saver was inactive. Adjust
the positions of the daemon and the text and clip them accordingly
each time.
- Don't call set_border() too often. Some video chip may produce
flicker.
Pointed out by tony@dell.com
- Don't fill the entire screen with blank char every time the saver is
called. Blank only the part of the screen where the daemon and the
text was previously printed.
PPP_DEFLATE options... The code uses #if defined(PPP_DEFLATE) etc, so the
original method of "#define PPP_DEFLATE 0" did not actually disable
anything. It was not possible to configure out bsdcomp or zlib
compression. Also, join the settings for PPP_FILTER and NBPFILTER together
since they are related here (can't have PPP_FILTER without NBPFILTER).
savers are also modified so that they behave in the same way as the
blank saver on MDA and CGA, although it's not the way these screen
savers are supposed to work, but fading monitor and tickling green
monitor cannot be done on MDA and CGA, AFAIK. So, this is the second
best solution.
As of this change, the current state of support of screen savers is
summarized in the following table.
MDA CGA EGA VGA
blank OK OK NA OK
daemon OK OK OK OK
fade * * NA OK
green * * NA OK
snake OK OK OK OK
star OK OK OK OK
OK: works
NA: doesn't work, the module cannot be loaded for this adapter.
*: behave the same way as the blank saver.
As you can see, EGA is left out for now. But, we can do no better, as
EGA registers cannot be read...
Reviewed by: sos
facilitate the new saver loading/unloading notification interface
in syscons.
daemon_saver:
- M_NOWAIT was wrong, since NULL returns are not handled. Just use
M_WAITOK.
- use `ostype' instead of hard-coded "FreeBSD". Now there is no more
hard-coded string! (But, who will run this screen saver on other
OS?!)
- put macros and data declarations in a consistent order.
- -DDEAMON_ONLY and -DSHOW_HOSTNAME options added in the previous commit
are removed. Options of this kind can go stale and no one notices
because no one uses them. DEAMON_ONLY is just removed. SHOW_HOSTNAME
is made default.
snake_saver:
- use `ostype' and `osrelease' as in the daemon saver. The string changes
slightly - there was a hyphen after "FreeBSD"; now there is a space.
(It is consistent with uname -a, like the daemon server already is.)
all screen savers:
- Use the new add_scrn_saver()/remove_scrn_saver() in syscons.c
to declare loading/unloading of a screen saver. Removed reference
to `current_saver' and the variable `old_saver' as they are not
necessary anymore.
- The blank, fade and green screen savers manipulate VGA registers.
Module loading should fail for non-VGA cards.
- `scrn_blanked' is consistently treated as a number/counter rather
than boolean.
- Some savers touch `scp->start' and `scp->end' to force entire screen
update when stopping themselves. This is unnecessary now because
syscons.c takes care of that.
- cleared up many unused or unnecessary #include statements.
- Removed -DLKM from Makefiles.
YOU NEED TO RECOMPILE BOTH SCREEN SAVERS AND KERNEL AS OF THIS CHANGE.
rather than hard-code it in the message text. Optinally include
the host name in the message if SHOW_HOSTNAME is defined.
The origianl idea and sample code submitted by Angelo Turetta
<ATuretta@stylo.it>.
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
were declared as non-const. This is backwards (_lkm_exec() changes the
pointers but all the target `struct execsw's are const). Fixed this
and poisoned related declarations to match and removed the bogus casts
that hid the bug.
too late to be used in all cases. It should probably be created (early)
in bsd.kmod.mk for all LKMs.
Use cc instead of cpp | as for the same reasons as in the kernel makefile.
CFLAGS isn't split up as well as in the kernel makefile, but cc doesn't
pass compiler warning flags to cpp, so there is no need to split it.
LKM'ness. ACTUALLY_LKM_NOT_KERNEL is supposed to be so ugly that it
only gets used until <machine/conf.h> goes away. bsd.kmod.mk should
define a better-named general macro for this. Some places use
PSEUDO_LKM. This is another bad name.
Makefile:
Added IPFIREWALL_VERBOSE_LIMIT option (commented out).
Compile and link a new kernel, that will give native ELF support, and
provide the hooks for other ELF interpreters as well.
To make native ELF binaries use John Polstras elf-kit-1.0.1..
For the time being also use his ld-elf.so.1 and put it in
/usr/libexec.
The Linux emulator has been enhanced to also run ELF binaries, it
is however in its very first incarnation.
Just get some Linux ELF libs (Slackware-3.0) and put them in the
prober place (/compat/linux/...).
I've ben able to run all the Slackware-3.0 binaries I've tried
so far.
(No it won't run quake yet :)
from a string to an identifier so that it can be used to generate
declarations and strings. It's much easier to stringize an identifier
than to identifize a string. A uniform naming scheme must be used
for the automatically generated things to apply. This is a feature.
Used the module identifer to generate prototypes for the module load,
unload and stat functions. Removed the few prototypes for these that
already existed.
Used the module identifier to generate a unique struct tag in MOD_DEV().
This should probably be done for all the MOD_*() macros.
Moved the trailing semicolon from the MOD_*() macro definitions to the
macro invocations that didn't already (bogusly) have it.
Staticized the module load and unload functions.
Added function return types for the module load, unload and stat functions.
lkm/ibcs2/ibcs2.c:
Included <sys/sysproto.h> to get everything prototyped.
Cleaned up #includes.
lkm/ibcs2/ipfw.c:
Cleaned up #includes.
lkm/linux/linux.c:
The module name had to change from "linux_emulator" to "linux_mod" to
be automatically generated.
Cleaned up #includes.
lkm/syscons/*/*_saver.c:
Completed delcarations of function pointers.
sys/i386/isa/atapi.c:
The module name had to change from "atapi" to "atapi_mod" to be
automatically generated.
sys/i386/isa/wcd.c:
Used the fixed MOD_DEV(). This module has two devices and expanded the
macro in the source instead of fixing it.
The module names had to change from "wcd" and "rwcd" to "wcd_mod" and
"rwcd_mod" to be automatically generated.
sys/pccard/pcic.c:
The module name had to change from "pcic" to "pcic_mod" to be
automatically generated.
convention of having their entry point named "<modname>_mod"".
Symorder is enforcing this when the current bsd.kmod.mk is installed.
I've not tested all these, but at least they all compile now.
Reattach them to the makefile.
Note that the change that I made to symorder needs to be compiled and
installed before any LKM's will work - the last version was corrupting
the relocation tables. A "make world" will to this, but if you
manually run a make on the lkm's you'll need to take care of it by
hand.
