Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
mark crypto requests with ``callback immediately'' to avoid doing a context
switch to return crypto results. This completes the work to eliminate
context switches for using software crypto via the crypto subsystem (with
symmetric crypto ops).
software crypto device:
o record crypto device capabilities in each session id
o add a capability that indicates if the crypto driver operates synchronously
o tag the software crypto driver as operating synchronously
This commit also introduces crypto session id macros that cleanup their
construction and querying.
an MSDOSFS file system either failed, silently corrupted the file, or
sometimes corrupted the neighboring file.
PR: 53695
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my> (original version)
MFC: 3 days
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
bus_dma async callback scheme. Note that sparc64 does not seem to do
async callbacks. Note that ia64 callbacks might not be MPSAFE at the
moment. Note that powerpc doesn't seem to do async callbacks due to
the implementation being incomplete.
Reviewed by: mostly silence on arch@
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
o add back rx monitor support
o make WI_RID_SCAN_RES DTRT
o fix a bug handling zero-length RID requests (used by dstumbler to set
a zero-length SSID)
o make RID_SCAN_REQ DTRT
o add back WI_RID_OWN_SSID
o fix wi_scan_ap to take a channel mask and txrate (for prism cards)
These changes fix dstumbler -o (monitor mode). A minor change to dstumbler
is needed to get normal AP scanning mode to work right; this is preferred to
modifying the driver.
PR: kern/53187
Reviewed by: Bruce M Simpson <bms@spc.org>
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
when the user specifies a maximum fragment size < 2.
This is the behavior that Linux provides and fixes the problem I've
observed in Tribes2 where sounds effects are delayed by 1/2 a second.
This commit has two pieces. One half is the watchdog kernel code which lives
primarily in hardclock() in sys/kern/kern_clock.c. The other half is a userland
daemon which, when run, will keep the watchdog from firing while the userland
is intact and functioning.
Approved by: jeff (mentor)
being requested is outside of the range of the direct map region. eg:
for pci windows. While here, increase the minimum size of the direct
map region to be 4GB instead of 1GB.
so can leave stale data in the buffer and confuse the driver.
- enable the ability to set the 'disable' hint for the driver to keep it
from attaching. i.e. 'hw.ips.0.disable=1' will prevent the driver from
attaching.
- Only detach if attach suceeded.
Submitted by: mjacob
Before, we would add/subtract the leap second when the system had been
up for an even multiple of days, rather than at the end of the day, as
a leap second is defined (at least wrt ntp). We do this by
calculating the notion of UTC earlier in the loop, and passing that to
get it adjusted. Any adjustments that ntp_update_second makes to this
time are then transferred to boot time. We can't pass it either the
boot time or the uptime because their sum is what determines when a
leap second is needed. This code adds an extra assignment and two
extra compare in the typical case, which is as cheap as I could made
it.
I have confirmed with this code the kernel time does the correct thing
for both positive and negative leap seconds. Since the ntp interface
doesn't allow for +2 or -2, those cases can't be tested (and the folks
in the know here say there will never be a +2s or -2s leap event, but
rather two +1s or -1s leap events).
There will very likely be no leap seconds for a while, given how the
earth is speeding up and slowing down, so there will be plenty of time
for this fix to propigate. UT1-UTC is currently at "about -0.4s" and
decrementing by .1s every 8 months or so. 6 * 8 is 48 months, or 4
years.
-stable has different code, but a similar bug that was introduced
about the time of the last leap second, which is why nobody has
noticed until now.
MFC After: 3 weeks
Reviewed by: phk
"Furthermore, leap seconds must die." -- Cato the Elder
incremented at the start of the leap second, not after the leap second
has been inserted. This is because at the start of the leap second,
we set the time back one second. This setting back one second is the
moment that the offset changes. The old code set it back after the
leap second, but that's one second too late. The negative leap second
case is handled correctly.
Reviewed by: phk
of pcpu locks. This makes uma_zone somewhat smaller (by (LOCKNAME_LEN *
sizeof(char) + sizeof(struct mtx) * maxcpu) bytes, to be exact).
No Objections from jeff.
