These definitions will be used by a driver to implement Hardware
P-States (autonomous control of HWP, via Intel Speed Shift technology).
Reviewed by: kib
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D18050
Just allow MSI interrupts to always start at the end of the I/O APIC
pins. Since existing machines already have more than 255 I/O APIC
pins, IRQ 255 is no longer reliably invalid, so just remove the
minimum starting value for MSI.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D17991
SDM rev. 068 was released yesterday and it contains the description of
the MSR 0x10a IA32_ARCH_CAP. This change adds symbolic definitions for
all bits present in the document, and decode them in the CPU
identification lines printed on boot.
But also, the document defines SSB_NO as bit 4, while FreeBSD used but
2 to detect the need to work-around Speculative Store Bypass
issue. Change code to use the bit from SDM.
Similarly, the document describes bit 3 as an indicator that L1TF
issue is not present, in particular, no L1D flush is needed on
VMENTRY. We used RDCL_NO to avoid flushing, and again I changed the
code to follow new spec from SDM.
In fact my Apollo Lake machine with latest ucode shows this:
IA32_ARCH_CAPS=0x19<RDCL_NO,SKIP_L1DFL_VME,SSB_NO>
Reviewed by: bwidawsk
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
Differential revision: https://reviews.freebsd.org/D18006
The number of MSI IRQs still defaults to 512, but it can now be
changed at boot time via the machdep.num_msi_irqs tunable.
Reviewed by: kib, royger (older version)
Reviewed by: markj
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D17977
The off-by-one errors in 332735 weren't actual errors and were
preventing the last MSI interrupt source from being used. Instead,
the issue is that when all MSI interrupt sources were allocated, the
loop in msix_alloc() would terminate with 'msi' still set to non-null.
The only check for 'i' overflowing was in the 'msi' == NULL case, so
msix_alloc() would try to reuse the last MSI interrupt source instead
of failing.
Fix by moving the check for all sources being in use to just after the
loop.
Reviewed by: kib, markj
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D17976
We need to know actual value for the standard extended features before
ifuncs are resolved.
Reported and tested by: madpilot
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Avoid using DELAY() since it can try to use spin locks on CPUs without
a P-state invariant TSC. For cpu_lock_delay(), always use the TSC if
it exists (even if it is not P-state invariant) to delay for a
microsecond. If the TSC does not exist, read from I/O port 0x84 to
delay instead.
PR: 228768
Reported by: Roger Hammerstein <cheeky.m@live.com>
Reviewed by: kib
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17851
This uses slightly simpler logic than the existing code by using the
full 64-bit counter and thus not having to worry about counter
overflow.
Reviewed by: kib
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17850
On some Intel devices BIOS does not properly reserve memory (called
"stolen memory") for the GPU. If the stolen memory is claimed by the
OS, functions that depend on stolen memory (like frame buffer
compression) can't be used.
A function called pci_early_quirks that is called before the virtual
memory system is started was added. In Linux, this PCI early quirks
function iterates through all PCI slots to check for any device that
require quirks. While this more generic solution is preferable I only
ported the Intel graphics specific parts because I think my
implementation would be too similar to Linux GPL'd solution after
looking at the Linux code too much.
The code regarding Intel graphics stolen memory was ported from
Linux. In the case of Intel graphics stolen memory this
pci_early_quirks will read the stolen memory base and size from north
bridge registers. The values are stored in global variables that is
later read by linuxkpi_gplv2. Linuxkpi stores these values in a
Linux-specific structure that is read by the drm driver.
Relevant linuxkpi code is here:
https://github.com/FreeBSDDesktop/kms-drm/blob/drm-v4.16/linuxkpi/gplv2/src/linux_compat.c#L37
For now, only amd64 arch is suppor ted since that is the only arch
supported by the new drm drivers. I was told that Intel GPUs are
always located on 0:2:0 so these values are hard coded for now.
Note that the structure and early execution of the detection code is
not required in its current form, but we expect that the code will be
added shortly which fixes the potential BIOS bugs by reserving the
stolen range in phys_avail[]. This must be done as early as possible
to avoid conflicts with the potential usage of the memory in kernel.
Submitted by: Johannes Lundberg <johalun0@gmail.com>
Reviewed by: bwidawsk, imp
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D16719
Differential revision: https://reviews.freebsd.org/D17775
Remove malloc_domain(9) and most other _domain KPIs added in r327900.
The new functions allow the caller to specify a general NUMA domain
selection policy, rather than specifically requesting an allocation from
a specific domain. The latter policy tends to interact poorly with
M_WAITOK, resulting in situations where a caller is blocked indefinitely
because the specified domain is depleted. Most existing consumers of
the _domain KPIs are converted to instead use a DOMAINSET_PREF() policy,
in which we fall back to other domains to satisfy the allocation
request.
This change also defines a set of DOMAINSET_FIXED() policies, which
only permit allocations from the specified domain.
Discussed with: gallatin, jeff
Reported and tested by: pho (previous version)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17418
All platforms except powerpc use the same values and powerpc shares a
majority of them.
Go ahead and declare AT_NOTELF, AT_UID, and AT_EUID in favor of the
unused AT_DCACHEBSIZE, AT_ICACHEBSIZE, and AT_UCACHEBSIZE for powerpc.
Reviewed by: jhb, imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D17397
This provides a chicken switch for anyone negatively impacted by
enabling NUMA in the amd64 GENERIC kernel configuration. With
NUMA disabled at boot-time, information about the NUMA topology
is not exposed to the rest of the kernel, and all of physical
memory is viewed as coming from a single domain.
This method still has some performance overhead relative to disabling
NUMA support at compile time.
PR: 231460
Reviewed by: alc, gallatin, kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17439
Pre-defined policies are useful when integrating the domainset(9)
policy machinery into various kernel memory allocators.
The refactoring will make it easier to add NUMA support for other
architectures.
No functional change intended.
Reviewed by: alc, gallatin, jeff, kib
Tested by: pho (part of a larger patch)
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17416
The change is a no-op for architectures which don't ifunc memset,
memcpy nor memmove.
Convert places which need them. Xen bits by royger.
Reviewed by: kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17487
This caused microcode to be updated only on the BSP if hyperthreading
was disabled, typically resulting in a hang or reset.
Approved by: re (kib)
Sponsored by: The FreeBSD Foundation
The AMD Threadripper 2990WX is basically a slightly crippled Epyc.
Rather than having 4 memory controllers, one per NUMA domain, it has
only 2 memory controllers enabled. This means that only 2 of the
4 NUMA domains can be populated with physical memory, and the
others are empty.
Add support to FreeBSD for empty NUMA domains by:
- creating empty memory domains when parsing the SRAT table,
rather than failing to parse the table
- not running the pageout deamon threads in empty domains
- adding defensive code to UMA to avoid allocating from empty domains
- adding defensive code to cpuset to avoid binding to an empty domain
Thanks to Jeff for suggesting this strategy.
Reviewed by: alc, markj
Approved by: re (gjb@)
Differential Revision: https://reviews.freebsd.org/D1683
Use these predicates instead of inline references to vm_min_domains.
Also add a global all_domains set, akin to all_cpus.
Reviewed by: alc, jeff, kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17278
This simplifies the runtime logic and reduces the number of
runtime-constant branches.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Differential revision: https://reviews.freebsd.org/D16736
The atpic_register_sources callback tries to avoid registering interrupt
sources that would collide with an I/O APIC. However, the previous
implementation was failing to register IRQs 8-15 since the slave PIC
saw valid IRQs from the master and assumed an I/O APIC was present. To
fix, go back to registering all 8259A interrupt sources in one loop when
the master's register_sources method is invoked.
PR: 231291
Approved by: re (kib)
MFC after: 1 month
Register interrupts using the PIC pic_register_sources method instead
of doing it in apic_setup_io. This is now required, since the internal
interrupt structures are not yet setup when calling apic_setup_io.
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
Instead of panicking. Legacy PVH mode doesn't provide a lapic, and
since native_lapic_intrcnt is called unconditionally this would cause
the assert to trigger. Change the assert into a continue in order to
take into account the possibility of systems without a lapic.
Reviewed by: jhb
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
Differential revision: https://reviews.freebsd.org/D17015
The recommended way to obtain the vcpu id is using the cpuid
instruction with a specific leaf value. This leaf value must be
obtained at runtime, and it's done when populating the hypercall page.
Legacy PVH however will get the hypercall page populated by the
hypervisor itself before booting, so the cpuid leaf was not actually
set, thus preventing setting the vcpu id value from cpuid.
Fix this by making sure the cpuid leaf has been probed before
attempting to set the vcpu id.
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
That's the only mode in FreeBSD that requires the usage of PIRQs, so
there's no need to attach the PIRQ PIC when running in other modes.
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
When adding support for the new PVH mode the kenv handling was
switched to use a boot time allocated scratch space, however the
legacy PVH early boot code was not modified to allocate such space.
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
The vcpu_id for legacy PVH mode can be set from the output of cpuid,
so there's no need to have a special function to set it.
Also note that xenpv_set_ids should have been executed only for PV
guests, but was executed for all guests types and vcpu_id was later
fixed up for HVM guests.
Reported by: cperciva
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
So that it's done when the vcpu_id has been set. For the BSP the
vcpu_id is set at SUB_INTR, while for the APs it's done in
init_secondary_tail that's called at SUB_SMP order FIRST.
Reported and tested by: cperciva
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
Differential revision: https://reviews.freebsd.org/D17013
When running as a specific type of Xen guest the hypervisor won't
provide any emulated IO-APICs or legacy PICs at all, thus hitting the
following assert in the MSI code:
panic: Assertion num_io_irqs > 0 failed at /usr/src/sys/x86/x86/msi.c:334
cpuid = 0
time = 1
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xffffffff826ffa70
vpanic() at vpanic+0x1a3/frame 0xffffffff826ffad0
panic() at panic+0x43/frame 0xffffffff826ffb30
msi_init() at msi_init+0xed/frame 0xffffffff826ffb40
apic_setup_io() at apic_setup_io+0x72/frame 0xffffffff826ffb50
mi_startup() at mi_startup+0x118/frame 0xffffffff826ffb70
start_kernel() at start_kernel+0x10
Fix this by removing the assert in the MSI code, since it's possible
to get to the MSI initialization without having registered any other
interrupt sources.
Reviewed by: jhb
Approved by: re (gjb)
Sponsored by: Citrix Systems R&D
Differential revision: https://reviews.freebsd.org/D17001
Previously, x86 used static ranges of IRQ values for different types
of I/O interrupts. Interrupt pins on I/O APICs and 8259A PICs used
IRQ values from 0 to 254. MSI interrupts used a compile-time-defined
range starting at 256, and Xen event channels used a
compile-time-defined range after MSI. Some recent systems have more
than 255 I/O APIC interrupt pins which resulted in those IRQ values
overflowing into the MSI range triggering an assertion failure.
Replace statically assigned ranges with dynamic ranges. Do a single
pass computing the sizes of the IRQ ranges (PICs, MSI, Xen) to
determine the total number of IRQs required. Allocate the interrupt
source and interrupt count arrays dynamically once this pass has
completed. To minimize runtime complexity these arrays are only sized
once during bootup. The PIC range is determined by the PICs present
in the system. The MSI and Xen ranges continue to use a fixed size,
though this does make it possible to turn the MSI range size into a
tunable in the future.
As a result, various places are updated to use dynamic limits instead
of constants. In addition, the vmstat(8) utility has been taught to
understand that some kernels may treat 'intrcnt' and 'intrnames' as
pointers rather than arrays when extracting interrupt stats from a
crashdump. This is determined by the presence (vs absence) of a
global 'nintrcnt' symbol.
This change reverts r189404 which worked around a buggy BIOS which
enumerated an I/O APIC twice (using the same memory mapped address for
both entries but using an IRQ base of 256 for one entry and a valid
IRQ base for the second entry). Making the "base" of MSI IRQ values
dynamic avoids the panic that r189404 worked around, and there may now
be valid I/O APICs with an IRQ base above 256 which this workaround
would incorrectly skip.
If in the future the issue reported in PR 130483 reoccurs, we will
have to add a pass over the I/O APIC entries in the MADT to detect
duplicates using the memory mapped address and use some strategy to
choose the "correct" one.
While here, reserve room in intrcnts for the Hyper-V counters.
PR: 229429, 130483
Reviewed by: kib, royger, cem
Tested by: royger (Xen), kib (DMAR)
Approved by: re (gjb)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16861
error in the function hypercall_memfree(), where the wrong arena was being
passed to kmem_free().
Introduce a per-page flag, VPO_KMEM_EXEC, to mark physical pages that are
mapped in kmem with execute permissions. Use this flag to determine which
arena the kmem virtual addresses are returned to.
Eliminate UMA_SLAB_KRWX. The introduction of VPO_KMEM_EXEC makes it
redundant.
Update the nearby comment for UMA_SLAB_KERNEL.
Reviewed by: kib, markj
Discussed with: jeff
Approved by: re (marius)
Differential Revision: https://reviews.freebsd.org/D16845
Add pmap_activate_boot() for i386, move the invocation on APs from MD
init_secondary() to x86 init_secondary_tail().
Suggested by: alc
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (marius)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D16893
In pre-SMPng, the global 'imen' was used to track mask state of the
hardware interrupts and was aligned to the masks used by spl*().
When the atpic code was converted to using the x86 interrupt source
abstraction, the global 'imen' was preserved by having each PIC
instance point to an invididual byte in the global 'imen' to hold its
8-bit interrupt mask. The global 'imen' is no longer used for
anything however, so rather than storing pointers in 'struct atpic',
just store the individual 8-bit mask for each PIC as a char.
While here, convert the ATPIC macro to using C99 initializers.
Reviewed by: kib, imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16827
became unused in FreeBSD 12.x as a side-effect of the NUMA-related
changes.)
Reviewed by: kib, markj
Discussed with: jeff, re@
Differential Revision: https://reviews.freebsd.org/D16825
The MPTable probe code was using PMAP_MAP_LOW as the PA -> VA offset
when searching for the table signature but still using KERNBASE once
it had found the table. As a result, the mpfps table pointed into a
random part of the kernel text instead of the actual MP Table.
Rather than adding more #ifdef's, use BIOS_PADDRTOVADDR from
<machine/pc/bios.h> which already uses PMAP_MAP_LOW on i386 and KERNBASE
on amd64.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D16802
The support for lazy pmap invalidations on i386 was removed in r281707.
This removes the constant for the IPI and stops accounting for it when
sizing the interrupt count arrays.
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16801
At some point memcpy() may be an ifunc, ifunc resolution cannot be done
until CPU identification has been performed, and CPU identification must
be done after loading any microcode updates.
X-MFC with: r337715
Sponsored by: The FreeBSD Foundation
Updates in the format described in section 9.11 of the Intel SDM can
now be applied as one of the first steps in booting the kernel. Updates
that are loaded this way are automatically re-applied upon exit from
ACPI sleep states, in contrast with the existing cpucontrol(8)-based
method. For the time being only Intel updates are supported.
Microcode update files are passed to the kernel via loader(8). The
file type must be "cpu_microcode" in order for the file to be recognized
as a candidate microcode update. Updates for multiple CPU types may be
concatenated together into a single file, in which case the kernel
will select and apply a matching update. Memory used to store the
update file will be freed back to the system once the update is applied,
so this approach will not consume more memory than required.
Reviewed by: kib
MFC after: 6 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D16370
Previously, this check was omitted for the first frame pointer.
Reported by: pho
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16572
The timespecadd(3) family of macros were imported from NetBSD back in
r35029. However, they were initially guarded by #ifdef _KERNEL. In the
meantime, we have grown at least 28 syscalls that use timespecs in some
way, leading many programs both inside and outside of the base system to
redefine those macros. It's better just to make the definitions public.
Our kernel currently defines two-argument versions of timespecadd and
timespecsub. NetBSD, OpenBSD, and FreeDesktop.org's libbsd, however, define
three-argument versions. Solaris also defines a three-argument version, but
only in its kernel. This revision changes our definition to match the
common three-argument version.
Bump _FreeBSD_version due to the breaking KPI change.
Discussed with: cem, jilles, ian, bde
Differential Revision: https://reviews.freebsd.org/D14725
the AMD document 55449 'Revision Guide for AMD Family 17h Models
00h-0Fh Processors' rev 1.12.
The errata numbers are mentioned near each action.
It seems that newer BIOSes already include required chicken bits
settings, so the magic MSR updates are only needed when BIOS cannot be
updated. On the other hand, MWAIT avoidance seems to be important.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
