Debugnet is a simplistic and specialized panic- or debug-time reliable
datagram transport. It can drive a single connection at a time and is
currently unidirectional (debug/panic machine transmit to remote server
only).
It is mostly a verbatim code lift from netdump(4). Netdump(4) remains
the only consumer (until the rest of this patch series lands).
The INET-specific logic has been extracted somewhat more thoroughly than
previously in netdump(4), into debugnet_inet.c. UDP-layer logic and up, as
much as possible as is protocol-independent, remains in debugnet.c. The
separation is not perfect and future improvement is welcome. Supporting
INET6 is a long-term goal.
Much of the diff is "gratuitous" renaming from 'netdump_' or 'nd_' to
'debugnet_' or 'dn_' -- sorry. I thought keeping the netdump name on the
generic module would be more confusing than the refactoring.
The only functional change here is the mbuf allocation / tracking. Instead
of initiating solely on netdump-configured interface(s) at dumpon(8)
configuration time, we watch for any debugnet-enabled NIC for link
activation and query it for mbuf parameters at that time. If they exceed
the existing high-water mark allocation, we re-allocate and track the new
high-water mark. Otherwise, we leave the pre-panic mbuf allocation alone.
In a future patch in this series, this will allow initiating netdump from
panic ddb(4) without pre-panic configuration.
No other functional change intended.
Reviewed by: markj (earlier version)
Some discussion with: emaste, jhb
Objection from: marius
Differential Revision: https://reviews.freebsd.org/D21421
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
Make sure the enter and leave polling routines can be called multiple times
with same setting. Ignore setting polling or event mode twice. This fixes a
deadlock during shutdown if polling mode was already selected.
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx4_en_stop_port() calls mlx4_en_put_qp() which can refer the link level
address of the network interface, which in turn will be freed by the
network interface detach function. Make sure the port is stopped
before detaching the network interface.
MFC after: 1 week
Sponsored by: Mellanox Technologies
It can happen during shutdown that the lock will recurse when the mlx4en(4)
instance is part of a lagg interface. Call ether_ifdetach() unlocked.
Backtrace:
panic(): _sx_xlock_hard: recursed on non-recursive sx &mdev->state_lock
_sx_xlock_hard()
_sx_xlock()
mlx4_en_ioctl()
if_setlladdr()
lagg_port_destroy()
lagg_port_ifdetach()
if_detach()
mlx4_en_destroy_netdev()
mlx4_en_remove()
mlx4_remove_device()
mlx4_unregister_device()
mlx4_unload_one()
mlx4_shutdown()
linux_pci_shutdown()
bus_generic_shutdown()
MFC after: 1 week
Sponsored by: Mellanox Technologies
Copy small packets like TCP ACKs into a new mbuf
reusing the existing mbuf to receive a new ethernet
frame. This avoids wasting buffer space for
small sized packets.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being defined.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The "priv->pkstats.rx_dropped" is written twice in a row.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Also when the MTU is greater than MCLBYTES.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware queues are deep enough currently and using the DRBR and associated
callbacks only leads to more task switching in the TX path. The is also a race
setting the queue_state which can lead to hung TX rings.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
In last mlx4 update (r325841) we lost the sysctl to show the
firmware version for mlx4 devices.
Add both board identifier and firmware version under:
sys.device.mlx4_core0.hw sysctl node.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
When acting as a VF it is required to add steering rules for all unicast
addresses. Even if promiscious mode is selected. Else incoming data packets
will be dropped.
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
When receiving a PCP change all GID entries are reloaded.
This ensures the relevant GID entries use prio tagging,
by setting VLAN present and VLAN ID to zero.
The priority for prio tagged traffic is set using the regular
rdma_set_service_type() function.
Fake the real network device to have a VLAN ID of zero
when prio tagging is enabled. This is logic is hidden inside
the rdma_vlan_dev_vlan_id() function which must always be used
to retrieve the VLAN ID throughout all of ibcore and the
infiniband network drivers.
The VLAN presence information then propagates through all
of ibcore and so incoming connections will have the VLAN
bit set. The incoming VLAN ID is then checked against the
return value of rdma_vlan_dev_vlan_id().
MFC after: 1 week
Sponsored by: Mellanox Technologies
This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
Creating a UD address handle from user-space or from the kernel-space,
when the link layer is ethernet, requires resolving the remote L3
address into a L2 address. Doing this from the kernel is easy because
the required ARP(IPv4) and ND6(IPv6) address resolving APIs are readily
available. In userspace such an interface does not exist and kernel
help is required.
It should be noted that in an IP-based GID environment, the GID itself
does not contain all the information needed to resolve the destination
IP address. For example information like VLAN ID and SCOPE ID, is not
part of the GID and must be fetched from the GID attributes. Therefore
a source GID should always be referred to as a GID index. Instead of
going through various racy steps to obtain information about the
GID attributes from user-space, this is now all done by the kernel.
This patch optimises the L3 to L2 address resolving using the existing
create address handle uverbs interface, retrieving back the L2 address
as an additional user-space information structure.
This commit combines the following Linux upstream commits:
IB/core: Let create_ah return extended response to user
IB/core: Change ib_resolve_eth_dmac to use it in create AH
IB/mlx5: Make create/destroy_ah available to userspace
IB/mlx5: Use kernel driver to help userspace create ah
IB/mlx5: Report that device has udata response in create_ah
MFC after: 1 week
Sponsored by: Mellanox Technologies
These were made redundant in r325841.
Reviewed by: hselasky
MFC after: 1 week (hselasky will MFC)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13401
Background:
The coming ibcore update forces an update of mlx4ib(4) which in turn requires
an updated mlx4 core module. This also affects the mlx4en(4) module because
commonly used APIs are updated. This commit is a middle step updating the
mlx4 modules towards the new ibcore.
This change contains no major new features.
Changes in mlx4:
a) Improved error handling when mlx4 PCI devices are
detached inside VMs.
b) Major update of codebase towards Linux 4.9.
Changes in mlx4ib(4):
a) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Changes in mlx4en(4):
a) Update flow steering code in mlx4en to use new APIs for
registering MAC addresses and IP addresses.
b) Update all statistics counters to be 64-bit.
c) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Sponsored by: Mellanox Technologies
MFC after: 1 week
iWarp and RoCE in ibcore. The selection of RDMA_PS_TCP can not be used
to indicate iWarp protocol use. Backport the proper IB device
capabilities from Linux upstream to distinguish between iWarp and
RoCE. Only allocate the additional socket required for iWarp for RDMA
IDs when at least one iWarp device present. This resolves
interopability issues between iWarp and RoCE in ibcore
Reviewed by: np @
Differential Revision: https://reviews.freebsd.org/D12563
Sponsored by: Mellanox Technologies
MFC after: 3 days
Follow up from r324201 to fix compilation with gcc, which complains
about non-ICE case expressions.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D12675
is in VF or SRIOV mode typically in a virtual machine environment.
Submitted by: Sepherosa Ziehau <sephe@dragonflybsd.org>
MFC after: 3 days
Sponsored by: Mellanox Technologies
The m_defrag() function can only defrag mbuf chains which have a valid
mbuf packet header. In r291699 when the mlx4en(4) driver was converted
into using BUSDMA(9), the call to m_defrag() was moved after the part
of the transmit routine which strips the header from the mbuf chain.
This effectivly disabled the mbuf defrag mechanism and such packets
simply got dropped.
This patch removes the stripping of mbufs from a chain and loads all
mbufs using busdma. If busdma finds there are no segments, unload
the DMA map and free the mbuf right away, because that means all
data in the mbuf has been inlined in the TX ring. Else proceed
as usual.
Add a per-ring rounter for the number of defrag attempts and
make sure the oversized_packets counter gets zeroed while at it.
The counters are per-ring to avoid excessive cache misses in the
TX path.
Submitted by: mjoras@
Differential Revision: https://reviews.freebsd.org/D11683
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add io_mapping_init_wc() and add a third (unused) parameter to
io_mapping_map_wc().
Reviewed by: hselasky
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D11286
mlx4en network interfaces. This prevents infinite unit number growth
typically when the mlx4en driver is used inside virtual machines which
support runtime PCI attach and detach.
MFC after: 3 days
Sponsored by: Mellanox Technologies
