aic7xxx_pci.c:
Enable board generation of interrupts only once our handler is
in place and all other setup has occurred.
aic7xxx.c:
More conversion of data types to ahc_* names. tmode_tstate and
tmode_lstate are the latest victims.
Clean up the check condition path by branching early rather
than indenting a giant block of code.
Add support for target mode initiated sync negotiation.
The code has been tested by forcing the feature on for
all devices, but for the moment is left inaccesible until
a decent mechanism for controlling the behavior is complete.
Implementing this feature required the removal of the
old "target message request" mechanism. The old method
required setting one of the 16 bit fields to initiate
negotiation with a particular target. This had the nice
effect of being easy to change the request and have it
effect the next command. We now set the MK_MESSAGE bit
on any new command when negotiation is required. When
the negotiation is successful, we walk through and clean
up the bit on any pending commands. Since we have to walk
the commands to reset the SCSI syncrate values so no additional
work is required. The only drawback of this approach is that
the negotiation is deferred until the next command is queued to
the controller. On the plus side, we regain two bytes of
sequencer scratch ram and 6 sequencer instructions.
When cleaning up a target mode instance, never remove the
"master" target mode state object. The master contains
all of the saved SEEPROM settings that control things like
transfer negotiations. This data will be cloned as the
defaults if a target mode instance is re-instantiated.
Correct a bug in ahc_set_width(). We neglected to update
the pending scbs to reflect the new parameters. Since
wide negotiation is almost always followed by sync
negotiation it is doubtful that this had any real
effect.
When in the target role, don't complain about
"Target Initiated" negotiation requests when an initiator
negotiates with us.
Defer enabling board interrupts until after ahc_intr_enable()
is called.
Pull all info that used to be in ahc_timeout for the FreeBSD
OSM into ahc_dump_card_state(). This info should be printed
out on all platforms.
aic7xxx.h:
Add the SCB_AUTO_NEGOITATE scb flag. This allows us to
discern the reason the MK_MESSAGE flag is set in the hscb
control byte. We only want to clear MK_MESSAGE in
ahc_update_pending_scbs() if the MK_MESSAGE was set due
to an auto transfer negotiation.
Add the auto_negotiate bitfield for each tstate so that
behavior can be controlled for each of our enabled SCSI
IDs.
Use a bus interrupt handler vector in our softc rather
than hard coding the PCI interrupt handler. This makes
it easier to build the different bus attachments to
the aic7xxx driver as modules.
aic7xxx.reg:
Remove the TARGET_MSG_REQUEST definition for sequencer ram.
aic7xxx.seq:
Fix a few target mode bugs:
o If MK_MESSAGE is set in an SCB, transition to
message in phase and notify the kernel so that
message delivery can occur. This is currently
only used for target mode initiated transfer
negotiation.
o Allow a continue target I/O to compile without
executing a status phase or disconnecting. If
we have not been granted the disconnect privledge
but this transfer is larger than MAXPHYS, it may
take several CTIOs to get the job done.
Remove the tests of the TARGET_MSG_REQUEST field in scratch ram.
aic7xxx_freebsd.c:
Add support for CTIOs that don't disconnect. We now defer
the clearing of our pending target state until we see a
CTIO for that device that has completed sucessfully.
Be sure to return early if we are in a target only role
and see an initiator only CCB type in our action routine.
If a CTIO has the CAM_DIS_DISCONNECT flag set, propogate
this flag to the SCB. This flag has no effect if we've
been asked to deliver status as well. We will complete
the command and release the bus in that case.
Handle the new auto_negotiate field in the tstate correctly.
Make sure that SCBs for "immediate" (i.e. to continue a non
disconnected transaction) CTIO requests get a proper mapping
in the SCB lookup table. Without this, we'll complain when
the transaction completes.
Update ahc_timeout() to reflect the changes to ahc_dump_card_state().
aic7xxx_inline.h:
Use ahc->bus_intr rather than ahc_pci_intr.
two subject ucreds. Unlike p_cansee(), u_cansee() doesn't have
process lock requirements, only valid ucred reference requirements,
so is prefered as process locking improves. For now, back p_cansee()
into u_cansee(), but eventually p_cansee() will go away.
Reviewed by: jhb, tmm
Obtained from: TrustedBSD Project
locks were held, we could be preempted and switch CPU's in between the time
that we set a variable to the list of spin locks on our CPU and the time
that we checked that variable to ensure no spinlocks were held while
grabbing a sleep lock. Losing the race resulted in checking some other
CPU's spin lock list and bogusly panicing.
* Initialize the "struct sockaddr_dl sdl" correctly in vlan_setmulti().
PR: kern/22181
* The driver used to call malloc(..., M_NOWAIT), but to not check the
return value. Change malloc(..., M_NOWAIT) to malloc(..., M_WAITOK)
because the corresponding part of code is called from the upper
half of the kernel only.
PR: kern/22181
* Make sure a parent interface is up and running before invoking
its if_start() routine in order to avoid system panic.
PR: kern/22179 kern/24741 i386/25478
* Do not copy all the flags from a parent mindlessly.
PR: kern/22179
* Do not call if_down() on a parent interface if it's already down.
Call if_down() at splimp because if_down() needs that.
PR: kern/22179
Reviewed by: wollman
Change code from PRC_UNREACH_ADMIN_PROHIB to PRC_UNREACH_PORT for
ICMP_UNREACH_PROTOCOL and ICMP_UNREACH_PORT
And let TCP treat PRC_UNREACH_PORT like PRC_UNREACH_ADMIN_PROHIB
This should fix the case where port unreachables for udp returned
ENETRESET instead of ECONNREFUSED
Problem found by: Bill Fenner <fenner@research.att.com>
Reviewed by: jlemon
decode the BIOS and firmware version and announce the board as HP NetRaid.
This has been tested with a NetRaid 3si controller, the BIOS/firmware
printout should also work for other NetRaid controllers but the type
detection for other NetRaids (such as the 1si) will not work due to the
lack of hardware.
Reviewed by: msmith
- Introduce lock classes and lock objects. Each lock class specifies a
name and set of flags (or properties) shared by all locks of a given
type. Currently there are three lock classes: spin mutexes, sleep
mutexes, and sx locks. A lock object specifies properties of an
additional lock along with a lock name and all of the extra stuff needed
to make witness work with a given lock. This abstract lock stuff is
defined in sys/lock.h. The lockmgr constants, types, and prototypes have
been moved to sys/lockmgr.h. For temporary backwards compatability,
sys/lock.h includes sys/lockmgr.h.
- Replace proc->p_spinlocks with a per-CPU list, PCPU(spinlocks), of spin
locks held. By making this per-cpu, we do not have to jump through
magic hoops to deal with sched_lock changing ownership during context
switches.
- Replace proc->p_heldmtx, formerly a list of held sleep mutexes, with
proc->p_sleeplocks, which is a list of held sleep locks including sleep
mutexes and sx locks.
- Add helper macros for logging lock events via the KTR_LOCK KTR logging
level so that the log messages are consistent.
- Add some new flags that can be passed to mtx_init():
- MTX_NOWITNESS - specifies that this lock should be ignored by witness.
This is used for the mutex that blocks a sx lock for example.
- MTX_QUIET - this is not new, but you can pass this to mtx_init() now
and no events will be logged for this lock, so that one doesn't have
to change all the individual mtx_lock/unlock() operations.
- All lock objects maintain an initialized flag. Use this flag to export
a mtx_initialized() macro that can be safely called from drivers. Also,
we on longer walk the all_mtx list if MUTEX_DEBUG is defined as witness
performs the corresponding checks using the initialized flag.
- The lock order reversal messages have been improved to output slightly
more accurate file and line numbers.
We really want to be able to say "auto NWAY", "limited NWAY", and
"no NWAY". Unfortunately, this does not appear to be possible with
the current mediaopt structure.
and change the u_int mtx_saveintr member of struct mtx to a critical_t
mtx_savecrit.
- On the alpha we no longer need a custom _get_spin_lock() macro to avoid
an extra PAL call, so remove it.
- Partially fix using mutexes with WITNESS in modules. Change all the
_mtx_{un,}lock_{spin,}_flags() macros to accept explicit file and line
parameters and rename them to use a prefix of two underscores. Inside
of kern_mutex.c, generate wrapper functions for
_mtx_{un,}lock_{spin,}_flags() (only using a prefix of one underscore)
that are called from modules. The macros mtx_{un,}lock_{spin,}_flags()
are mapped to the __mtx_* macros inside of the kernel to inline the
usual case of mutex operations and map to the internal _mtx_* functions
in the module case so that modules will use WITNESS and KTR logging if
the kernel is compiled with support for it.
sections.
- Add implementations of the critical_enter() and critical_exit() functions
and remove restore_intr() and save_intr().
- Remove the somewhat bogus disable_intr() and enable_intr() functions on
the alpha as the alpha actually uses a priority level and not simple bit
flag on the CPU.
- If there is no gdb device, just return without trying to return any
value since gdb_handle_exception() returns void.
- When calling prom_halt(), pass in a value telling it to actually halt
and not to randomly choose whether or not to halt or reboot depending on
whatever value happened to be in a0 when the call was made.
an AST results in a signal being delivered, we'll need to do a full register
restore so as to properly setup the signal handler. This is somewhat of
a pessimization, because ast() will be called twice in this case.
This fixes several problems that have been reported where signal intensive
userland apps (most notably dump) have been SEGV'ing for no fault of their
own.
Thanks to Peter Jeremy <peter.jeremy@alcatel.com.au> for presenting the
AST scenario which led to me fiinally figuring this out.
Reviewed by: jhb
process we're looking for. (I don't think this can currently
happen, but it depends how the function is called).
PR: 25932
Submitted by: David Xu <davidx@viasoft.com.cn>
The fixes the problem of PLAY_BIG not being implemented on
some modern drives.
The problem now is that some old drives use BSD encoding
in the MSF case, which they dont tell, and which is also
not according to spec *sigh*. Hopefully there are not
too many of those still alive, or I hereby grant
license to kill the firmware writers that wrote the mess.
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
implementation is still experimental, and while fairly broadly tested,
is not yet intended for production use. Support for POSIX.1e ACLs on
UFS will not be MFC'd to RELENG_4.
This implementation works by providing implementations of VOP_[GS]ETACL()
for FFS, as well as modifying the appropriate access control and file
creation routines. In this implementation, ACLs are backed into extended
attributes; the base ACL (owner, group, other) permissions remain in the
inode for performance and compatibility reasons, so only the extended and
default ACLs are placed in extended attributes. The logic for ACL
evaluation is provided by the fs-independent kern/kern_acl.c.
o Introduce UFS_ACL, a compile-time configuration option that enables
support for ACLs on FFS (and potentially other UFS-based file systems).
o Introduce ufs_getacl(), ufs_setacl(), ufs_aclcheck(), which
respectively get, set, and check the ACLs on the passed vnode.
o Introduce ufs_sync_acl_from_inode(), ufs_sync_inode_from_acl() to
maintain access control information between inode permissions and
extended attribute data.
o Modify ufs_access() to load a file access ACL and invoke
vaccess_acl_posix1e() if ACLs are available on the file system
o Modify ufs_mkdir() and ufs_makeinode() to associate ACLs with newly
created directories and files, inheriting from the parent directory's
default ACL.
o Enable these new vnode operations and conditionally compiled code
paths if UFS_ACL is defined.
A few notes:
o This implementation is fairly widely tested, but still should be
considered experimental.
o Currently, ACLs are not exported via NFS, instead, the summarizing
file mode/etc from the inode is. This results in conservative
protection behavior, similar to the behavior of ACL-nonaware programs
acting locally.
o It is possible that underlying binary data formats associated with
this implementation may change. Consumers of the implementation
should expect to find their local configuration obsoleted in the
next few months, resulting in possible loss of ACL data during an
upgrade.
o The extended attributes interface and implementation is still
undergoing modification to address portable interface concerns, as
well as performance.
o Many applications do not yet correctly handle ACLs. In general,
due to the POSIX.1e ACL model, behavior of ACL-unaware applications
will be conservative with respects to file protection; some caution
is recommended.
o Instructions for configuring and maintaining ACLs on UFS will be
committed in the near future; in the mean time it is possible to
reference the README included in the last UFS ACL distribution
placed in the TrustedBSD web site:
http://www.TrustedBSD.org/downloads/
Substantial debugging, hardware, travel, or connectivity support for this
project was provided by: BSDi, Safeport Network Services, and NAI Labs.
Significant coding contributions were made by Chris Faulhaber. Additional
support was provided by Brian Feldman, Thomas Moestl, and Ilmar Habibulin.
Reviewed by: jedgar, keichii, mckusick, trustedbsd-discuss, freebsd-fs
Obtained from: TrustedBSD Project
