the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
level implementation stuff out of machine/globaldata.h to avoid exposing
UPAGES to lots more places. The end result is that we can double
the kernel stack size with 'options UPAGES=4' etc.
This is mainly being done for the benefit of a MFC to RELENG_4 at some
point. -current doesn't really need this so much since each interrupt
runs on its own kstack.
then one can restart from a panic by resetting the panicstr variable to
NULL. This commit conditionalizes the previously committed functionality
on this variable. It also removes the __dead2 attribute from the panic()
function so that when one continues from a panic() the behavior will
be predictable.
information. The default limits only effect machines with > 1GB of ram
and can be overriden with two new kernel conf variables VM_SWZONE_SIZE_MAX
and VM_BCACHE_SIZE_MAX, or with loader variables kern.maxswzone and
kern.maxbcache. This has the effect of leaving more KVM available for
sizing NMBCLUSTERS and 'maxusers' and should avoid tripups where a sysad
adds memory to a machine and then sees the kernel panic on boot due to
running out of KVM.
Also change the default swap-meta auto-sizing calculation to allocate half
of what it was previously allocating. The prior defaults were way too high.
Note that we cannot afford to run out of swap-meta structures so we still
stay somewhat conservative here.
"./foo.ko". Use "/full/path/foo.ko" instead so that when the path is
reported as being an absolute path to the "shared library", at least
it's not really a relative path.
Obtained from: LOMAC/FreeBSD project
just before the memory hole to 4 megs. Special case building exception.s
like locore.s, it needs to at the beginning so the branches out from the
trap table don't overflow.
commented out in the entire life of the 2.x+ branch and given the amount
of gcc-specific code we have and the warning checks that gcc does I'm not
sure that it is going to get us much for some time.
debugging support as well. Debugging module support is handled
identically to kernel debugging support, right down to poor
choice of make variable names.
Tunables are now derived at boot time from maxusers. ie: change maxusers
via a tunable and all the derivative settings change. You can change
the other tunables individually as well. Even hz etc is tunable.
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
directory does not exist, instead of creating/overwriting a file
with the name of the (expected) directory. Yes, this deviates a bit
from nearly all other install targets in the tree, but let's face it,
removing a modules directory is not all that uncommon a mistake,
and finding a file with the contents of the last module installed
is a baaad surprise at boot time..
PR: 26317
Submitted by: "T. William Wells" <bill@twwells.com> (the PR)
Gregory Bond <gnb@itga.com.au> (the actual patch)
Reviewed by: silence on -arch and -audit for the last 10 days
MFC after: 2 weeks
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
- All sources are built in a single object, reducing namespace pollution.
- Kill the ready queue, and handle a busy response to mly_start in callers
rather than deferring the command.
- Improve our interaction with CAM:
- Don't advertise physical channels as SCSI busses by default.
- use the SIM queue freeze capability rather than queueing CDBs internally.
- force bus reprobe at module load time.
- Clean up more resources in mly_free.
- Tidy up debugging levels.
- Tidy up handling of events (mostly just code cleanliness).
- Use explanatory macros for operations on bus/target/channel numbers.
