the device is suspended or shutting down. This will need to be rethought
slightly if we implement suspend/resume support within vr(4).
This appears to fix the vr_shutdown() panic on SMP machines.
My theory here is there's a race somewhere during vr_detach() with
vr_intr() in the SMP case which was sometimes being triggered,
although quite why this was happening is unclear (vr_stop() also
explicitly disables interrupts by writing to the IMR register).
MFC-to-RELENG_5* candidate.
PR: kern/62889
Tested by: seb at struchtrup dot com
MFC after: 10 days
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
two loops in agp_generic_bind_memory(). As an intended side-effect, all
of the calls to vm_page_wakeup() are now performed with the containing
vm object lock held.
o Instead of locking and unlocking all over the place, use
lock assertions to make certain that the bfe lock is held
where necessary.
o Create locked and unlocked versions of bfe_init and bfe_start. These
functions can be called from outside the module and by functions
within the bfe module. The calls from outside the module don't
hold the bfe lock so the unlocked versions called by these functions
simple obtain the bfe lock and call the locked version.
- Fix a typo (scp) in the locking macros that only worked because in all the
instances in which it was called the softc pointer happened to be named 'sc'.
- Mark the interrupt MPSAFE
Tested by: matusita, Dario Freni <saturnero@gufi.org>
Silence from: -net, wpaul
with a weak memory model or x86 + PAE (or more specifically, your
driver is using bounce pages) and you have had problems with em(4),
this may fix it. At least this is needed to have em(4) work properly
on FreeBSD/arm.
Original version by: cognet
Reviewed by: tackerman
Tested by: cognet
Add constants for SPI protocol delays that are needed for
target mode.
aic7xxx.c:
Correct a target mode issue that caused an occassional
spurious REQ to be seen on the bus when performing manual
message processing (e.g. transfer rate negotiation).
Enforce phase change bus settle rules with explicit
delays when performing manual message processing in
target mode. The sequencer already did this for
"fast-path", target mode message processing.
as the original logic did. This fixes a race with vr_intr() which was
masked on UP systems and manifested on SMP systems.
PR: kern/62889
MFC after: 1 day
the ATA pccard locking function. This makes pccard devices like
Compact Flash cards work again.
PR: kern/72805
Submitted by: James E. Flemer <jflemer@alum.rpi.edu>
MFC in: 2 days
frames. BGE hardware with the rx alignment bug will still be handled by the
calls to m_adj() that already exist. m_adj() is probably better suited for
this task anyways. Just as with if_em, this saves a malloc + several locks
per packet and prevents unneeded data copying within busdma.
Since the e1000 DMA engines hava no constraints on the alignment of buffer
transfers, there is no reason to tell busdma that there is. This save a
minimum of 1 malloc call per packet, which translates to eliminating 4 locks.
It also means that buffers are not needlessly bounced when transfered. The
end result is a 38% improvement in pps in a 4 way bridging environment.
Obtained from: Sandvine, Inc.
(usually taking 20 seconds to transmit a packet).. no longer fall back
to only transmitting one packet (instead of the entire queue) after we
have processed the entire send queue... I have no idea why we didn't
start seeing this problem ~6 years ago when this code was introduced...
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
