Changes are to
- update board and network interface detection logic
- fix reading onboard CPLD in little-endian config
- print NAE frequency conrrectly for Bx chips
- update XAUI config to disable Rx/Tx until interface is up
Submitted by: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
The changes are:
- the microcore code loaded into the NAE has to be byteswapped
in LE
- the descriptors in memory for a P2P NAE descriptor has to be
byteswapped in LE
- the m_data pointer is already cacheline aligned, so the
unnecessary m_adj to cacheline size can be removed
- fix mask used to obtain physical address from the Tx freeback
descriptor
- fix a compile error in code under #ifdef
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
The CMS output queue credit configuration register is 64 bit, so use
a 64 bit variable while updating it.
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
Update MDIO reset code to support Broadcom XLP B1 revisions.
Update nlm_xlpge_ioctl, nlm_xlpge_port_enable need not be
called after nlm_xlpge_init.
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
Support few more versions of board firmware. In case the security
block is disabled, enable it at boot. Also increase the excluded
memory region to cover the area used by the firmware to initialize
devices.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.
Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
* Update message station (CMS) code, read queue ids from PCI header.
* Use interrupts to wakeup message handling threads on 3XX
* Update PIC code, read interrupt information from PCI header instead
of using fixed values.
* Update PCI interrupt handling for the PIC change.
* Update code for getting chip frequency, new code support XLP 3XX
* Misc style(9) fixes
In collaboration with: prabhath at netlogicmicro com (CMS/PIC)
venkatesh at netlogicmicro.com (PCI)
* Update the hardware access register definitions and functions to bring
them in line with other Netlogic software.
* Update the platform bus to use PCI even for on-chip devices. Add a dummy
PCI driver to ignore on-chip devices which do not need driver.
* Provide memory and IRQ resource allocation code for on-chip devices
which cannot get it from PCI config.
* add support for on-chip PCI and USB interfaces.
* update conf files, enable pci and retain old MAXCPU until we can support
>32 cpus.
Approved by: re(kib), jmallett
