which requires OVREF to be set to get proper playback volume, but which has
all zeroes in HDA controller subdevice IDs on PCI.
MFC after: 1 month
Sponsored by:
detailed information under the sound debug. To make it easier accessible,
export that information through the set of sysctls like dev.hdaa.X.nidY.
Also tune some output to make it both more compact and informative.
from HDMI/DisplayPort devices in form of general connection status and
sound(4)-style channel matrix. Now that information is only reported in
readable form to verbose logs, but potentially could be used by sound(4)
to correctly choose default devices and configure vchans.
Fix rear and side channels swap on analog 7.1 outputs. As soon as there is
a huge mess in industry about naming and using of these channels, duplicate
rear channels of 4 and 5.1 streams to both read and side speakers.
if unused in that configuration mixer at NID 15 is muted. Probably CODEC
incorrectly reports its internal connections. Hide that muter from the
driver to avoid muting and make built-in speaker work.
There are several different CODECs sharing this ID and I have not enough
information about them and the bug to implement more universal solution.
Tested by: Big Yuuta <init.py@gmail.com>
MFC after: 2 weeks
with the real value in regular way if sensing is supported. This fixes
minor inconsistency when playback redirection appeared in undefined state
on boot if headphones were not connected.
device drivers that used to provide this feature.
This is a subset of 241856 (which was reverted)
Reviewed by: des
Approved by: cperciva (implicit)
MFC after: 1 week
make analog input loopback and dual-stream playback work by enabling
signal mixing by nid 22, as it should be according to info returned by
the CODEC. Otherwise pin nid 28 receives only signal from DAC nid 16.
PR: kern/169124
MFC after: 1 week
at r230551.
Also while there, make sense polling use reported for each node separately
instead of reporting accumulated total status.
Submitted by: Barbara <barbara.freebsd@gmail.com> (1)
MFC after: 3 days
names to shorten them. PulseAudio reported to have problems with names
longer then 63 chars and at least in XMMS long names are inconvinient.
Reported by: hselasky
MFC after: 3 days
The cs driver requires a table with firmware values. An
alternative firmware is available in a similar Open Sound
System driver. This is actually a partial revert of
Revision 77504.
Special thanks to joel@ for patiently testing several
replacement attempts.
The csa driver and the complete sound system are now free
of the GPL.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
Remove unneeded temporary variable (data) to better match the OSS code.
Remove some unused constants and type definitions.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
- add "+HP" in case of headphones redirection;
- add device type for analog devices, if all pins have the same.
As result now it may look like "Analog 5.1+HP/2.0" or "Front Analog Mic".
I hope it will be more useful than long and confusing.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
