Rather than relying on 'cluster' existing in the context they're used in,
use the argument name.
Differential Revision: https://reviews.freebsd.org/D12931
This fixes some regulator issues with a83t/BananaPi-M3; the pin value was
getting clobbered as we reconfigured the pin when initializing the
regulator.
Discussed with: ian
Recent DTS (from Linux 4.14) specify a compatible "allwinner,sun50i-h5-ccu"
for H5 SoC. Since we get the DTB from u-boot this wasn't noticed.
Add the compatible so later version of u-boot will not fail for us.
a10_gpio previously accepted only {allwinner,}drive and {allwinner,}pull for
drive/bias setting, while newer DTS is using drive-strength and
bias-{disable,pull-up,pull-down} properties. Accept these properties as
well.
Additionally make bias and drive strength optional rather than required; not
setting them should just indicate that we do not need to configure these
properties.
Tested on: BananaPi-M3 (a83t)
Reviewed by: manu
Approved by: emaste (implicit)
Obtained from: NetBSD (partially)
Differential Revision: https://reviews.freebsd.org/D13284
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
For FreeBSD/arm64's cloudabi32 support, I'm going to need a TO_PTR() in
this place. Also use it for all of the other source files, so that the
difference remains as minimal as possible.
MFC after: 2 weeks
Originally a patch by Mark Millard, augmented with information from work
done on NetBSD by jmcneill@.
Submitted by: Mark Millard (markmi@dsl-only.net)
Reviewed by: emaste, manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13240
The r-ccu on the a83t differs from the others only by what it names the
ar100 parents. Export the _CCU macros (now converted to an enu) so that
ccu_sun8i_r can differentiate between a83t r-ccu and the others, then add
the compat string for the a83t r-ccu.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13206
plain-vanilla ETH microcode. The QOS_VLAN firmware added support in microcode
for handling IEEE 802.1q tags, but the npe(4) driver did not actually
support the relevant signalling. As a result, it was impossible to use
VLANs with npe(4). Switching to the more basic microcode (same license)
removes the on-NIC promisisng and makes vlan(4) work on both NPE interfaces.
Ref: https://lists.freebsd.org/pipermail/freebsd-arm/2012-August/003826.html
Upon successful completion, the execve() system call invokes
exec_setregs() to initialize the registers of the initial thread of the
newly executed process. What is weird is that when execve() returns, it
still goes through the normal system call return path, clobbering the
registers with the system call's return value (td->td_retval).
Though this doesn't seem to be problematic for x86 most of the times (as
the value of eax/rax doesn't matter upon startup), this can be pretty
frustrating for architectures where function argument and return
registers overlap (e.g., ARM). On these systems, exec_setregs() also
needs to initialize td_retval.
Even worse are architectures where cpu_set_syscall_retval() sets
registers to values not derived from td_retval. On these architectures,
there is no way cpu_set_syscall_retval() can set registers to the way it
wants them to be upon the start of execution.
To get rid of this madness, let sys_execve() return EJUSTRETURN. This
will cause cpu_set_syscall_retval() to leave registers intact. This
makes process execution easier to understand. It also eliminates the
difference between execution of the initial process and successive ones.
The initial call to sys_execve() is not performed through a system call
context.
Reviewed by: kib, jhibbits
Differential Revision: https://reviews.freebsd.org/D13180
A ccu driver was added for the a83t in r326114. Add compat string to
aw_ccung and register the clocks for the a83t upon attach.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13205
This value may be set by userspace so we need to check it before using it.
If this is not done correctly on exception return the kernel may continue
in kernel mode with all registers set to a userspace controlled value. Fix
this by moving the check into set_mcontext, and also add the missing
sanitisation from the arm64 set_regs.
Discussed with: security-officer@
MFC after: 3 days
Sponsored by: DARPA, AFRL
Upstream DTS has switched to using CCU rather than /clocks nodes. Add a CCU
driver for the a83t to bring us closer to upstream, but don't yet attach it
to ccu node.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12843
Add a means to specify mask/value for the prediv condition instead of
shift/width/value for clocks that have a more complex mux scenario.
Specifically, ahb1 on the a83t has the prediv applied if mux is either b10
or b11.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12851
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
We currently support the a83t's r_intc in a somewhat hack-ish way; our .dts
describes it as nmi_intc, and uses a subset of the actual register space to
make it line up with a20/a31 nmi offsets.
This breaks with the recent 4.14 update describing r_intc using the full
register space, so update aw_nmi to use the correct register offsets with
the right compat data in a way that doesn't break our current dts with
nmi_intc or upstream with r_intc described.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13122
Stale packets should not be transmitted when the interface comes up after being down.
Count the successfully transmitted ones for statistics and drop the rest.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12539
Use a spare dma map when attempting to map a new mbuf on the rx path.
If the mbuf allocation fails or the dma map loading for the new mbuf fails just reuse the old mbuf
and increase the drop counter.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12538
- use awg_encap and awg_txeof names to match iflib and other network drivers.
- handle m_collapse failure similarly by freeing the mbuf rather than reenqueuing it where it will continue to fail.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13035
TX_BUF_UA_INT is set when there are no buffers to transmit and can
happen before hw.awg.tx_interval segments have been transmitted.
To reduce load, tx cleanup should be done in hw.awg.tx_interval intervals.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13034
A packet may be built from multiple segments, don't increase the count for each segment
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13032
According to the datasheet, TX_DESC_CTL is cleared when whole frame is transmitted or all
data in the current descriptor's buffer are transmitted.
When the mbuf and mapping are stored in the first segment and in a scenario where a tx
completion interrupt arrives for a frame and only the start of the next frame was transmitted,
at the time of interrupt processing the mbuf and mapping will be freed when processing the
first segment of the next frame but the other untrasmitted segments still need to use them.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13031
In a multi segment frame, if the first tx descriptor is marked with TX_DESC_CTL
but not all tx descriptors for the other segments in the frame are set up,
the TX DMA may transmit an incomplete frame.
To prevent this, set TX_DESC_CTL for the first tx descriptor only when done
with all the other segments.
Also, don't bother cleaning transmitted tx descriptors since TX_DESC_CTL
is cleared for them by the hardware and they will be reprogrammed before
TX_DESC_CTL is reenabled for them.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13030
The hardware will not issue a completion interrupt for a descriptor
with TX_INT_CTL set if it doesn't also have TX_LAST_DESC set.
Submitted by: Guy Yur <guyyur_gmail.com>
Differential Revision: https://reviews.freebsd.org/D13029
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
Since r324184 the root node compatible for rpi2 is "brcm,bcm2836", add
it to the compatible list of bcm2835_cpufreq.
Tested On: RPI2 v1.1 RPI2 v1.2
Reported by: many on freebsd-arm@
DTS files switch from clocks under /clocks to a ccu (Clock Controller Unit)
a while ago.
Restore A13 functionality by adding a clock driver for it.
Almost every clocks are handled, the missing ones are mostly video related
clocks.
Tested On: A13 Olinuxino
The elf_trampoline.c is not connected to build for ARMv6/v7 for long time and
it uses outdated low level cpu functions.
This blocks forthcoming cleanup of ARM code.
MFC after: 3 weeks
Under certain traffic pattern awg driver does not recover from TX queue
full condition. The actual source of the problem is not identified yet
but jmcneill@ agreed that bumping TX_MAX_SEGS to 20 is OK as a workaround
for the problem (NetBSD has it set to 128).
Also add some diagnostic printfs to prevent silent failure of bus_dma
functions in the future
PR will be kept open until root cause of the issue is identified and fixed
PR: 219927
Submitted by: Tom Vijlbrief <tvijlbrief@gmail.com>
Approved by: jmcneill
MFC after: 2 weeks
emulation in fast path of data/prefetch abort common routine. Process
these bits only if related page table entries are consistent with
provided abort info. In case of inconsistency, do nothing and let
processor to signal new abort if still needed.
The mapping related to an abort may be a subject of change concurrently.
The situation is more evident on multicore machines. Mapping may be
removed on one core while being used on another one before TLB flush
happened. Memory swapping process may be an example. Or, two or more
aborts may be signaled for the same page on more cores concurrently.
While an abort on one core may cause a promotion of related mapping,
an abort on another core may be inconsistent then as related mapping
was promoted. A question is how much real the issue may be on single
core machine. However, it's better to play safe even for these machines.
This change may solve some "PT2MAP abort" panics reported rarely.
The revision of pmap_fault() was initiated thanks to stack backtrace
provided by Bob Prohaska (fbsd at www.zefox.net).
While here, INVARIANTS block was changed. The previous check had iffy
value as only one entry from many was checked from L2 page table.
Reviewed by: mmel
MFC after: 3 weeks
- allocate value for new AT_HWCAP2 auxiliary vector on all platforms.
- expand 'struct sysentvec' by new 'u_long *sv_hwcap2', in exactly
same way as for AT_HWCAP.
MFC after: 1 month
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D12699
HEAD. Enable VIMAGE in GENERIC kernels and some others (where GENERIC does
not exist) on HEAD.
Disable building LINT-VIMAGE with VIMAGE being default.
This should give it a lot more exposure in the run-up to 12 to help
us evaluate whether to keep it on by default or not.
We are also hoping to get better performance testing.
The feature can be disabled using nooptions.
Requested by: many
Reviewed by: kristof, emaste, hiren
X-MFC after: never
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D12639
All of the kernel dump implementations keep track of the current offset
("dumplo") within the dump device. However, except for textdumps, they
all write the dump sequentially, so we can reduce code duplication by
having the MI code keep track of the current offset. The new
dump_append() API can be used to write at the current offset.
This is needed to implement support for kernel dump compression in the
MI kernel dump code.
Also simplify dump_encrypted_write() somewhat: use dump_write() instead
of duplicating its bounds checks, and get rid of the redundant offset
tracking.
Reviewed by: cem
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D11722
It doesn't seems to be needed anymore and this make ehci working again
on the Pine64.
Thanks to jmcneill@ for the help.
Tested on: Pine64 (A64), OrangePi One (H3), BananapiM2 (A31s)
