because the act of doing the release kills the hints(!). A quirk of
the wrapper caused it to reset all the settings, except perhaps for the
memory address. I've tested this with a real SMC 8013EPC - which uses
shared memory addresses - it seems to work OK.
- fix cut/paste problem. :-)
- don't forget to call isa_dmacascade()
- reset the port after we release resources.
That last one is a trap to watch out for.. The isa bus driver uses the
same port/irq/mem/etc variables for the initial probe hints as it does
for allocation/deallocation tracking. Releasing a resource clears the
variable and then you loose the hint during attach.. (ouch!)
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.
Submitted by: Doug Rabson <dfr@nlsystems.com>
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
All it did was match a specific device ID and turn on a quirk for
the wdc driver.
Incidently, at line 1462 there is a return that prevents the generic
ide_pci code from trying to look at the device. I'd be interested
to know if we can take out the return and let the generic code "see" it.
I've left the return in because that's the way it worked before.
(Be sure to rerun config after cvsup or you'll get undefined files!)
perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
Reduce synth_info.name lenght for binary compatibility.
o sys/i386/isa/sound/mpu401.c
Reduce mpu device number info to avoid overflow of mpu_synth_info.name.
Submitted by: Akio Morita <amorita@meadow.scphys.kyoto-u.ac.jp>
Add Sound Card ID for the nss(NEC PC-9801-86 Sound System) driver.
Old name of this driver was pcm driver in FreeBSD 2.2.x.
Fix lack of the length of the name member of the synth_info structure.
(attach_mpu401 in sys/i386/isa/sound/mpu401.c requires 33 chars.)
o sys/i386/isa/sound/dev_table.h
Add the DMAbuf flags definition DMA_DISABLE.
Add the nss driver entry.
o sys/i386/isa/sound/dmabuf.c
Add the DMA_DISABLE flag check in DMAbuf_outputintr and DMAbuf_inputintr
to disable DMA control in FIFO only use (nss driver required).
o sys/i386/isa/sound/local.h
Add the nss driver entry.
o sys/i386/isa/sound/mpu401.c
Replace inb function in probe_mpu401 to mpu401_status macro.
Wrap macro argument for above replace.
Add I/O port maping macro for NEC PC-98x1 arch.
Add delay in NEC PC-98x1 arch.
o sys/i386/isa/sound/pcm86.c
Change driver name to avoid name space conflict to new pcm driver.
Fix NEC PC-9801-86 driver to work on RELENG_3 branch or latter.
o sys/i386/isa/sound/sound_calls.h
Fix the mpuintr definition.
Add the nss driver entry.
attach_nss, probe_nss, nssintr
o sys/i386/isa/sound/soundcard.c
Fix lack of the mpuintr registration.
Add the nss driver entry.
o sys/pc98/conf/files.pc98
Add the nss driver entry.
Reviewed by: kato
Submitted by: Akio Morita <amorita@meadow.scphys.kyoto-u.ac.jp>
- Make a copy of the information block returned in the vm86 space
by the VESA BIOS init function. Otherwise it will be overwritten
by subsequent BIOS calls in the same vm86 context.
